instrument panel FORD MUSTANG 1969 Volume One Chassis

01-01-02
Vehicle Identification
01-01-02

VEHICLE WARRANTY NUMBER

The vehicle warranty number is the first line of numbers and

letters appearing on the Warranty Plates (Fig. 1). The Warranty

Plate is riveted to the left front door lock face panel. The first

number indicates the model year. The letter following the model

year number indicates the manufacturing assembly plant. The next

two numbers designate the Body Serial Code followed by a letter

expressing the Engine Code. The group of six digits remaining on

the first line indicate the Consecutive Unit Number.

VEHICLE DATA

The vehicle data appears on the second or lower line on the

Warranty Plate. The first two numbers and a letter identify the

Body Style. A letter or a number appears next indicating the

Exterior Paint Color followed by a number-letter combination

designating the Interior Trim. To the right of this code appears the

Date Code indicating the date the car was manufactured. A two-

digit number next designates the district in which the car was

ordered and may appear in conjunction with a Domestic Special

Order or Foreign Special Order number when applicable. The final

two spaces indicate the Rear Axle Ratio (numbers for regular axles,

letters for locking-types) and the Transmission type (numbers for

manual,
letters for automatic).

OFFICIAL VEHICLE IDENTIFICATION NUMBER

The official Vehicle Identification Number (VIN) for title and

registration purposes is stamped on an aluminum tab that is riveted

to the instrument panel close to the windshield on the driver's side

of the car and is visible from outside (Fig. 2).

MODEL YEAR CODE

The number 9 designates 1969.

ASSEMBLY PLANT CODES
COUGAR

Code

Letter
Code

Letter

A

B

C

D

E

F

G

H

J

K
Atlanta
L

Oakville (Canada)
N

Ontario Truck
P

Dallas
R

.,
Mahwah
S

Dearborn
T

Chicago
U

Lorain
W

Los Angeles
X

Kansas City
Y

Z
Michigan Truck

Norfolk

Twin Cities

San Jose

.
(Pilot). ...Allen Park

Metuchen

Louisville

Wayne

St. Thomas

Wixom

St. Louis

BODY SERIAL AND STYLE CODES

The two-digit numeral which follows the assembly plant code

identifies the body series. This two-digit number is used in con-

junction with the Body Style Code, in the Vehicle Data, which

consists of a two-digit number with a letter suffix. The following

chart lists the Body Serial Codes, Body Style Codes and the model.

LINCOLN CONTINENTAL

Body Body

Serial Style

Code Code Body Type

82
53A
4-Door Sedan

80
65A
2-Door
Hardtop

CONTINENTAL MARK
III

Body Body

Serial Style

Code Code Body Type

89
65A
2-Door
Hardtop
Body

Serial

Code

91

92

93

94

91
Body

Style

Code

65A

76A

65B

76B

65C

® Bench Seat

MERCURY

Body

Serial

Code

44

46

48

45

40

41

42

54

56

58

63

66

68

65

63

66

68

60

61

72

72

74

74

76

76
Body

Style

Code

54A

65A

57A

76A

53M

65M

57M

54C

65B

57B

53F

65F

57 F

76F

53C

65C

57C

63G

63H

71B

71C

71F

71G

71E

71A

©Bench Seat
Body
Type

2-Door
Hardtop©

Convertible©

2-Door
Hardtop©

Convertible®

2-Door
Hardtop®
Model

Standard

XR-7 Luxury

Standard

©Split Bench ©Bucket Seats

Body Type

4-Door Sedan©

2-Door
Hardtop-Formal®

4-Door Hardtop®

Convertible®

CANADA ONLY

4-Door Hardtop Sedan®

2-Door
Hardtop-Formal®

4-Door Hardtop®

4-Door Sedan®

2-Door
Hardtop-Formal®

4-Door Hardtop®

4-Door Hardtop Sedan®©

2-Door
Hardtop-Formal®©

4-Door Hardtop®®

Convertible®®

4-Door Hardtop Sedan©

2-Door
Hardtop-Formal©

4-Door Hardtop©
Model

Monterey

Marquis

Monterey-Custom

Marquis

Brougham (Option)

2-Door
Hardtop (Tunnel Roof)®© Marauder

2-Door
Hardtop (Tunnel Roof)®®©

4-Door 2 Seat®

4-Door 3 Seat (Side Facing)®

4-Door
2
Seat®

4-Door 3 Seat (Side Facing)®

4-Door 2 Seat®©

4-Door 3 Seat (Side Facing)®©
Monterey Wagoi

Monterey-Custom Wagon

Marquis Colony Park

©Split Bench ©Bucket Seats

METEOR (CANADA)

Body

Serial

Code

20

21

23
Body

Style

Code

54A

54B

65B
Body Type

4-Door Sedan®

4-Door Sedan®

2-Door
Hardtop-Formal®
Model

Rideau

Rideau 500

30
54C
4-Door Sedan®

35
65C
2-Door
Hardtop-Formal®

35
65E
2-Door
Hardtop-Formal{5-33)®®

33
57C
4-Door Hardtop®

34
76C
Convertible®

34
76E
Convertible (S-33)®®
Montcalm

24
65F
2-Door
Hardtop-Formal®©

27
57F
4-Door Hardtop®®
LeMoyne

28
71B
Rideau 500-6 Passenger®

29
71C
Rideau 500-Dual Face Rear®

38
71E
Mo ntcalm-6 Passenger®

39
71A
Montcalm-Dual Face Rear®
Station Wagons.

©Bench Seat ©Splite Bench ©Bucket Seatsprocarmanuals.com

02-02-03
Brake System

02-02-03

DESCRIPTION

Disc brakes are available as option-

al equipment for the front wheels on

Ford, Mercury, Meteor, Fairlane,

Montego, Falcon, Mustang and Cou-

gar models and are standard on Thun-

derbird, Continental Mark III, and

Lincoln Continental models. The

dual-master cylinder equipped hydrau-

lic brake system employs single an-

chor, internal expanding and
self-

adjusting drum brake assemblies on

the rear wheels of vehicles with disc

brakes, and on the front and rear

wheels of all others.

A vacuum booster is used with the

power disc brake system.

DUAL MASTER CYLINDER

BRAKE SYSTEM

The dual-master cylinder brake sys-

tem has been incorporated in all mod-

els to provide increased safety. The

system consists of a dual-master cylin-

der (Fig. 1), pressure differential valve

assembly and a switch (Fig. 2). The

switch on the differential valve acti-

vates a dual-brake warning light, lo-

cated on the instrument panel.
DISC BRAKE

The disc brake consists of a venti-

lated rotor and caliper assembly. The

caliper used on all models except Lin-

coln Continental is a single piston

floating caliper (Fig. 3). The caliper

used on Lincoln Continental models is

a four piston fixed caliper (Fig. 4).

A proportioning valve in the rear

hydraulic circuit provides balanced

braking action between front and rear

brakes.

On all models except Lincoln a

pressure impulse valve located at the

primary inlet of the pressure differen-

tial valve prevents brake fluid surge

back to the master cylinder reservoir.

On Lincoln Continental models a

metering valve, in the hydraulic line

between the differential valve and the

front wheel disc brakes, prevents the

front brakes from applying until ap-

proximately 125 psi is obtained in the

system (Fig. 21). This delaying action

is required to prevent the front brakes

from performing all the braking ac-

tion on low speed stops and thereby

increasing the rate of lining wear.
FLOATING CALIPER—

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

The caliper asseml.y is made up of

a floating caliper housing assembly

and an anchor plate. The anchor plate

is bolted to .the wheel spindle arm by

two bolts. The floating caliper is at-

tached to the anchor plate by steel

stabilizers on Ford, Mercury, Meteor,

Thunderbird and Continental Mark

III models and by one stabilizer on

Fairlane, Montego, Falcon, Mustang

and Cougar models. The floating cali-

per slides on two locating pins which

also attach to the stabilizers. The

floating caliper contains the single cyl-

inder and piston assembly. The cylin-

der bore contains a piston with a

molded rubber dust boot to seal the

cylinder bore from contamination

(Fig. 5). A square section rubber pis-

ton seal is positioned in a groove in

the cylinder bore and is used to pro-

vide sealing between the cylinder and

piston (Fig. 7).

The outer brake shoe and lining as-

sembly is longer than the inner assem-

bly, and the shoe and lining

DISC BRAKES

RETURN SPRING

(SECONDARY)

RETAINER

PRIMARY SYSTEM BRAKE

FLUID RESERVOIR

BOOT

PUSH ROD

TUBE SEAT |

(SECONDARY)

BRAKE OUTLET

PORT
RESIDUAL \ ^

CHECK \

VALVE \

SECONDARY PISTON

ASSEMBLY
(PRIMARY)

BRAKE OUTLET

PORT
PRIMARY PISTON

ASSEMBLY
H 1545-A

FIG.
I
—
Dual
Master Cylinder—Typicalprocarmanuals.com

02-02-20
Brake System

02-02-20

1.
Disconnect the stoplight switch

wires at the connector. Remove the

spring retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then liftfthe switch straight upward

from the pin. Use care to avoid switch

damage during removal.

2.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

3.
Remove the brake tube from the

primary and secondary outlet ports of

the master cylinder.

4.
Remove the cap screws and lock-

washers that secure the master cylin-

der to the dirSh panel and lift the cyl-

inder forward and upward from the

vehicle.

Installation

1.
Position the boot on the push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening and position

the master cylinder on the panel.

2.
Install the cap screws at the dash

panel and torque them to specifica-

tion.

3.
Coat the nylon bushings with

SAE 10W oil. Install the nylon wash-

er and bushing on the brake pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder leaving the brake line

fittings loose.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

inch of the top of the dual reservoirs.

Use Ford Brake Fluid— Extra Heavy

Duty-Part Number C6AZ-19542-A

(ESA-M6C25-A) or equivalent for all

drum brake applications. The extra

heavy duty brake system fluid is col-

ored blue for identification. Do not

mix low temperature brake fluids with

the specified fluid for the power disc

brake system.

8. Bleed the dual-master cylinder

and the primary and secondary brake

systems. Centralize the pressure dif-

ferential valve. Refer to Hydraulic

System Bleeding and Centralizing of

the Differential Valve, Part 2-1, Sec-

tion 2 for proper procedure.

9. Operate the brakes several times,

then check for external hydraulic

leaks.
FAIRLANE, MONTEGO,

FALCON, MUSTANG AND

COUGAR

Removal

Refer to Figs. 27 and 28.

1.
Working from inside the vehicle

below the instrument panel, disconnect

the master cylinder push rod from the

brake pedal assembly. The push rod

cannot be removed from the master

cylinder.

2.
Disconnect the stoplight switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light

switch off the brake pedal pin just far

enough to clear the end of the pin,

then lift the switch straight upward

from the pin. Use care to avoid switch

damage during removal.

3.
Slide the master cylinder push

rod and the nylon washers and bush-

ings off the brake pedal pin.

4.
Remove the brake tubes from

the primary and secondary outlet

ports of the master cylinder.

5.
Remove the lock nuts or cap

screw and lockwashers that secure the

master cylinder to the dash panel and

lift the cylinder forward and upward

from the car.
Installation

Refer to Figs. 27 and 28.

1.
Position the boot on tie push

rod and secure the boot to the master

cylinder. Carefully insert the master

cylinder push rod and boot through

the dash panel opening.

2.
On Fairlane, Falcon or Montego

models, position the gasket and mas-

ter cylinder on the mounting studs on

the dash panel. Install the lock nuts

on the studs at the dash panel and

torque them to specification.

3.
On Mustang or Cougar models,

position the gasket and master cylin-

der on the dash panel. Install the re-

taining screws and torque them to

specification. Coat the nylon bushings

with SAE 10W oil. Install the nylon

washer and bushing on the brake

pedal pin.

4.
Position the stop light switch on

the brake pedal pin, install the nylon

bushing and washer and secure them

in position with the spring retainer.

5.
Connect the wires at the stop

light switch connector.

6. Connect the brake lines to the

master cylinder and tighten to speci-

fied torque.

7.
Fill the master cylinder with the

specified brake fluid to within 1/4

MASTER CYLINDER

IDENTIFICATION
UPPER STUD

SHAFT (AUTOf/lATIC

TRANSMISSION)

CLIP

BRAKE PEDAL

BUSHING SUPPORT

TUBE-2B253

TUBE-2A040
CLUTCH

PEDA_

LOWER STUD
STOP LITE

SWITCH

/ 13480

MASTER CYLINDER

PUSH ROD
BRAKE PEDAL

H 1556-C

FIG. 27—Dual Master Cylinder Installation—Non Power Brake

Fairlane, Montego, and Falconprocarmanuals.com

02-02-24
Brake
System

02-02-24

proportioning valve to the fender

apron and remove the proportioning

valve.

Installation

1.
Position the proportioning valve

to the fender apron.

2.
Connect the two brake lines at

the proportioning valve. Do not tight-

en.

3.
Install the bolt retaining the pro-

portioning valve to the fender apron.

4.
Tighten the brake line tube nuts

at the proportioning valve to specifica-

tions.

5.
Bleed the brakes and centralize

pressure differential valve.

THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 20.

1.
Disconnect the two hydraulic

brake lines at the master cylinder.

2.
Remove the two nuts retaining

the master cylinder to the booster and

remove the master cylinder for clear-

ance.

3.
Disconnect the two brake lines at

the proportioning valve.

4.
Remove the bolt and nut retain-

ing the proportioning valve to the

pressure differential valve bracket and

remove the proportioning valve assem-

bly.

Installation

1.
Transfer the bracket to the new

proportioning valve.

2.
Position the proportioning valve

assembly to the pressure differential

valve bracket.

3.
Connect the two brake lines to

the proportioning valve. Do not tight-

en.

4.
Install the bolt and nut retaining

the proportioning valve to the pressure

differential valve bracket.

5.
Tighten the two brake line tube

nuts at the proportioning valve to

specifications.

6. Position the master cylinder to

the booster and install the nuts retain-

ing the master cylinder to the booster.

7.
Connect the two brake lines at

the master cylinder and tighten the

tube nuts to specifications.

8. Bleed the brakes and centralize

the pressure differential valve.
LINCOLN CONTINENTAL

Removal

Refer to Fig. 21.

1.
Disconnect the two brake lines at

the proportioning valve.

2.
Loosen the bolt and nut on the

bracket retaining the proportioning

valve to the chassis.

3.
Remove the proportioning valve

from the bracket.

Installation

- 1. Position the proportioning valve

in the bracket and connect the two

brake lines. Do not tighten.

2.
Tighten the bolt and nut on the

bracket.

3.
Tighten the tube nuts on the

brake lines at the proportioning valve

to specifications.

4.
Bleed the brakes and centralize

the pressure differential valve.

PRESSURE METERING VALVE—

LINCOLN CONTINENTAL

REMOVAL

Refer to Fig. 21.

1.
Loosen the tube nuts connecting

the inlet and outlet tubes at the me-

tering valve, and remove the tubes.

2.
Remove the two screws retaining

the metering valve to the frame

crossmember, and remove the me-

tering valve. The metering valve is ser-

viced as an assembly only.

INSTALLATION

1.
Position the metering valve to

the frame crossmember, and install

the retaining screws.

2.
Connect the inlet and outlet

tubes to the metering valve, and tight-

en the tube nuts to specification.

BRAKE BOOSTER

REMOVAL

1.
Working from inside the\ vehicle

below the instrument panel, disconnect

the booster push rod from the brake

pedal assembly. To do this, proceed as

follows:

Disconnect the stop light switch

wires at the connector. Remove the

hairpin retainer. Slide the stop light
switch off from the brake pedal pin

just far enough for the switch outer

hole to clear the pin, and then remove

the switch from the pin and booster

push rod. Be careful not to damage

the switch during removal. Slide the

booster push rod and the nylon wash-

ers and bushing off the brake pedal

pin (Figs. 29 thru 33).

2.
Open the hood and remove the

master cylinder from the booster. Se-

cure it to one side without disturbing

the hydraulic lines. It is not necessary

to disconnect the brake lines, but care

should be taken that the brake lines

are not deformed. Permanent defor-

mation of brake lines can lead to tube

failure.

3.
Disconnect the manifold vacuum

hose or hoses from the booster unit.

4.
Remove the booster-to-dash

panel attaching nuts or bolts (Figs. 29

thru 33). Remove the booster and

bracket assembly from the dash panel,

sliding the push rod link out from the

engine side of the dash panel.

5.
On Fairlane, Montego, and Fal-

con models, remove the push rod link

boot from the dash panel.

INSTALLATION

1.
On Fairlane, Montego and Fal-

con models, install the push rod link

boot in the hole in the dash panel as

shown in Fig. 23. Install the four

spacers on the mounting studs.

2.
Mount the booster and bracket

assembly to the dash panel by insert-

ing the push rod or push rod link in

through the hole and boot in the dash

panel. Install the bracket-to-dash

panel attaching lock nuts or bolts

(Figs.
29 thru 33).

3.
Connect the manifold vacuum

hose or hoses to the booster.

4.
Before installing the master cyl-

inder, check the distance from the

outer end of the booster assembly

push rod to master cylinder surface.

Turn the screw in or out to obtain the

specified length. Refer to Part 2-1,

Section 2, Power Brake Master Cylin-

der Push Rod Adjustment. Install the

master cylinder and torque the attach-

ing nuts to specifications.

5.
Working from inside the vehicle

below the instrument panel, connect

the booster push rod link to the brake

pedal assembly. To do this, proceed as

follows:

Install the inner nylon washer, the

booster push rod, and the bushing on

the brake pedal pin. Position the

switch so that it straddles the push

rod with the switch slot on the pedal

pin and the switch outer hole justprocarmanuals.com

02-02-27
Brake System

02-02-27

4.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

5.
Torque the booster mounting

nuts to specifications.

LINCOLN CONTINENTAL

Removal

1.
Disconnect the battery ground

cable from the battery.

2.
It is necessary to obtain clear-

ance to remove vacuum hoses and the

electrical connector to the temperature

heat control box. Remove the two

screws retaining the relay to the fend-

er and push the relay aside. Discon-

nect the vacuum hoses and connector

at the heat control box.

3.
Working under the instrument

panel, disconnect the vacuum hoses,

wires and retaining clip from the tem-

perature heat control box. Remove the

two screws securing the temperature

control box to the dash panel.

4.
Remove the lower control hous-

ing retaining screws (6). Disconnect

the wire harnesses at the lower control

panel and place the panel aside. Re-

move the wire harness shield. Remove

the wire harness clip. Position the

wire harness aside. Remove the tem-

perature control box and position it

aside.

5.
Remove the hair-pin type retain-

er. Slide the stop light switch off the

brake pedal pin just far enough for

the switch outer hole to clear the pin.

Lift the switch upward from the pin.

Slide the master cylinder push rod,

nylon washers and bushing off the

brake pedal pin.

6. Remove the pivot bolt and nut

that holds the pedal to the pedal sup-

port bracket. Remove the brake pedal

assembly from the support bracket

and remove the bushings.

7.
If required, remove the brake

pedal pad retaining nuts and remove

the brake pedal pad.

Installation

1.
If the brake pedal pad was re-

moved, position the pad on the pedal.

Install the pad retaining nuts and tor-

que them to specification.

2.
Apply SAE 10 engine oil to the

bushings and locate all the bushings in

their proper places on the pedal as-

sembly.

3.
Install the brake pedal assembly

and bushings to the support bracket,

and then install the pivot bolt through
the support bracket and pedal assem-

bly. Install the pivot bolt nut and tor-

que it to specification.

4.
Install the inner nylon washer,the

master cylinder push rod link, and the

bushing on the brake pedal pin. Posi-

tion the switch so that it straddles the

push rod link with the switch slot on

the pedal and the switch outer hole

just clearing the pin. Install the outer

nylon washer as shown in Fig. 33. In-

stall the hair-pin type retainer on the

brake pedal pin.

5.
Connect the stop light switch

wires to the connector, and install the

wires in the retaining clip.

6. Position the wire harness and

clip on the temperature control box

and install the retaining screw. Posi-

tion the temperature control box to

the dash panel and install the two re-

taining bolts.

7.
Connect the vacuum lines and

the electrical connector to the control

box. Position the wire harness to the

control box and install the retaining

clip.

8. Position the wire harness shield

and install two retaining bolts.

9. Connect the wire harnesses to

the lower control panel and install the

retaining screws.

10.
Working within the engine

compartment, connect the wire con-

nector to the temperature heat control

box.

11.
Position the relay to the fender

apron and install the retaining bolts.

12.
Connect the ground cable to the

battery.

13.
Check the brakes and light

switch for proper operation. Close the

hood.

PARKING BRAKE CONTROL

ASSEMBLY

FORD, MERCURY

AND METEOR

Removal

Refer to Fig. 34.

1.
Make sure the parking brake is

fully released.

2.
Remove all tension from the rear

cables by backing off the adjusting nut

from the equalizer.

3.
Remove the roll pin that secures

the release knob to the cable and re-

move the knob.

4.
Remove the nut that secures the

release cable to the instrument panel
and remove the cable from the rear of

the instrument panel.

5.
Remove the two nuts attaching

the control assembly to the dash

panel.

6. Remove the cap screw attaching

the control assembly to the cowl side

bracket.

7.
Disconnect the hose to the park-

ing brake vacuum unit, if so equipped.

8. Remove the front cable assembly

retainer clip from the cable assembly

and disconnect the cable ball from the

control clevis.

9. Remove the control assembly

from the vehicle.

Installation

1.
Position the control assembly in

the vehicle.

2.
Fit the cable assembly through

its mounting hole and install the re-

taining clip. Connect the cable ball to

the control clevis.

3.
Connect the vacuum hose to the

parking brake unit, if so equipped.

4.
Install the attaching cap screw to

the cowl side bracket. Do not tighten.

5.
Install the two control assemb-

ly-to-dash panel nuts. Tighten the nuts

and the cap screw to specifications.

6. Insert the release cable into the

instrument panel and install the re-

taining nut.

7.
Install the release knob on the

cable with the roll pin.

8. Check the operation of the park-

ing brake. Adjust the parking brake

as required.

FAIRLANE, MONTEGO

AND FALCON

Removal

Refer to Fig. 35.

1.
Make sure the parking brake is

completely released.

2.
Remove all tension from the rear

cables by backing off the jam nut and

adjusting nut from the equalizer.

3.
Working inside the vehicle, re-

move the four bolts and one nut re-

taining the left air vent and cable as-

sembly to the dash and instrument

panels. Remove the vent assembly.

4.
Remove the parking brake front

cable ball retaining clip from the clev-

is.

5.
Disconnect the cable ball from

the notch in the brake clevis.

6. Remove the three screws that at-

tach the control assembly to the left

cowl inner side panel.procarmanuals.com

BRAKE PEDAL BRACKET

CABLE MUST BE TIGHT

ON -4 CROSSMEMBER

INSTRUMENT PANEL

VIEWZ

VACUUM RELEASE

INSTRUMENT PANEL

CONTROL CABLE
CABLE AND HOUSING R.H.
.25 INSULATOR

.00 TO CLIP

VIEWX

CABLE AND HOUSING L.H.

CLIP

CROSSMEMBER
CABLE AND HOUSING R.H.

LOWER SUSPENSION ARM

INTERMEDIATE CABLE

CONVERTIBLE ONLY

EQUALIZER

VIEWY

VIEWZ

MANUAL RELEASE
PRONGS MUST BE SECURELY

LOCKED IN PLACE WITHIN

BRAKE DRUM

L.H. SHOWN R.H. TYPICAL

H1645-A

FIG. 34—Parking Brake System—Ford, Mercury and Meteorprocarmanuals.com

02-02-30
Brake System

02-02-30

7.
Disconnect the wire lead at the

parking brake warning light switch

and remove the control assembly.

Installation

1.
Connect the wire lead to the

parking brake warning light switch.

2.
Position the control assembly to

the cowl inner side panel and install

the three attaching screws.

3.
Connect the ball-end of the park-

ing brake front cable assembly to the

control assembly, and install the hair-

pin retainer.

4.
Position the cable ball in the

notch in the brake clevis.

5.
Position the left air vent assem-

bly to the dash and instrument panels.

Install the four bolts and one nut re-

taining the air vent to the panels.

6. Check the operation of the park-

ing brake. Adjust the parking brake.

MUSTANG AND COUGAR

Removal

Refer to Fig. 36.

1.
Make sure the parking brake is

completely released,

2.
Remove all tension from the rear

cables by backing off the jam nut and

adjusting nut from the equalizer.

3.
Disconnect the wire lead at the

parking brake warning light switch (if

so equipped).

4.
Remove the parking brake front

cable ball retaining clip from the clev-

is.

5.
Remove the parking brake warn-

ing light switch and attaching screw (if

so equipped).

6. Disconnect the cable ball from

the notch in the brake clevis.

7.
Remove the three screws that at-

tach the control assembly to the left

cowl inner side panel.

8. Pull the control away from the

cowl, panel. Remove the hair-pin re-

tainer securing the front cable assem-

bly to the control assembly. Remove

the control assembly

Installation

1.
Connect the ball-end of the park-

ing brake front cable assembly to the

control assembly, and install the hair-

pin retainer.

2.
Position the control assembly to

the cowl inner side panel and install

the three attaching screws.
3.
Position the parking brake warn-

ing light switch and install the attach-

ing screw. Connect the parking brake

warning light switch wire lead (if vehi-

cle is so equipped).

4.
Position the cable ball in the

notch in the brake clevis.

5.
Check the operation of the park

ing brake. Adjust the parking brake.

THUNDERBIRD AND

CONTINENTAL MARK III

Removal

Refer to Fig. 37.

1.
Remove the two nuts retaining

the control to the dash panel.

2.
Remove two screws from the left

scuff plate.

3.
Remove one screw retaining the

left cowl trim panel and remove the

panel.

4.
Remove the two screws retaining

the left air duct and remove the air

duct.

5.
Remove the two screws retaining

the dimmer switch and position the

switch out of the way.

6. Remove the clip retaining the

cable assembly to the control.

7.
Disconnect the cable ball from

the control clevis.

8. Disconnect the vacuum hose at

the brake release.

9. Remove the bolt retaining the

control to the cowl side bracket and

remove the control.

Installation

1.
Position the parking brake con-

trol in the vehicle.

2.
Install the cable assembly in the

control and connect the cable ball to

the control clevis.

3.
Install the clip retaining the

cable to the control.

4.
Install the bolt retaining the con-

trol to the cowl side bracket.

5.
Connect the vacuum hose to the

parking brake release vacuum motor.

6. Position the dimmer switch and

install the retaining screws.

7.
Position the air duct and install

the retaining screws.

8. Position the cowl trim panel and

install the retaining screw.

9. Install the two scuff plate screws.

10.
Install the two nuts retaining

the control to the dash panel.

11.
Adjust the parking brakf
LINCOLN CONTINENTAL

Removal

Refer to Fig. 38.

1.
Raise the vehicle on a hoist.

2.
Loosen the parking brake cable

adjusting nut, remove the return

spring and remove the cable ball end

from the equalizer.

3.
Lower the vehicle.

4.
Disconnect the battery.

5.
Disconnect the wire harness con-

nector and two vacuum hoses at the

Automatic Temperature Control box.

6. Working inside the vehicle, re-

move the windshield wiper control

knob and bezel from the lower control

panel.

7.
Remove the screws retaining the

lower control panel. Lower the control

panel and disconnect wire harnesses

and vacuum hoses. Position the con-

trol panel aside.

8. Remove the screw retaining the

plastic wire cover and place 'the cover

aside.

9. Disconnect three vacuum hoses

and the wiring harness at the Auto-

matic Temperature Control box.

10.
Remove the two screws retain-

ing the Automatic Temperature Con-

trol box to the dash panel and remove

the box for clearance.

11.
Disconnect the ball end of the

cable from the control clevis.

12.
Remove the four bolts retaining

the control to the dash panel and

lower instrument panel flange.

13.
Disconnect the vacuum release

hose from the control and remove the

control assembly from the vehicle.

Installation

1.
Position the control assembly to

the dash panel and instrument panel

flange and install the four retaining

screws.

2.
Connect the vacuum release hose

to the control assembly.

3.
Connect the cable ball to the

control clevis.

4.
Position the Automatic Temper-

ature Control box to the dash panel

and install the retaining screws.

5.
Connect the wiring harness and

vacuum hoses to the Automatic Tem-

perature Control box.

6. Position the plastic wire covei

and install the retaining screw.

7.
Connect the wire harnesses and

vacuum lines to the lower control

panel and position the panel to the inprocarmanuals.com

03-05-05
Steering Columns And Linkage

03-05-05

TILT-AWAY STEERING

COLUMN REPAIRS

VACUUM RELEASE VALVE-

COUGAR AND MUSTANG

Removal

1.
Working from the underside of

the instrument panel disconnect the

hose from the valve.

2.
Disconnect the wire from the

connector on the valve and the con-

nector from the relay.

3.
Remove the bracket-

to-instrument panel attaching bolt and

let the bracket swing down.

4.
Remove the two screws that se-

cure the valve to the mounting bracket

and remove the valve.

Installation

1.
Secure the valve to the mounting

bracket with the two attaching screws.

2.
Position the bracket to the in-

strument panel and install the attach-

ing bolt.

3.
Connect the wire to the terminal

on the valve.

4.
Connect the hose from the vacu-

um motor to the horizontal connector

on the valve and the hose from the

reservoir to the vertical connector.

VACUUM RELEASE VALVE—

THUNDERBIRD

Removal

1.
Remove the lower finish panel.

2.
Disconnect the vacuum hose

from the vacuum release valve.

3.
Disconnect the vacuum release

valve electrical leads at the connector.

4.
Loosen the two attaching screws

holding the bracket to the dash. Lift

up the bracket to clear the screws and

swing it down below the panel.

5.
Remove the screws attaching the

valve to the panel and remove the

valve.

Installation

1.
Position the vacuum release

valve on the bracket.

2.
Install the two attaching screws

and swing the bracket up and over the

screws. Tighten the screws.

3.
Connect the electrical leads to

the wiring harness.
4.
Connect the hose from the vacu-

um dash panel junction block to the

connector on the vacuum release valve

that points downward and forward.

Connect the hose from the vacuum

motor to the other connector on the

release valve.

5.
Install the lower finish panel.

VACUUM MOTOR-

COUGAR AND MUSTANG

Removal

1.
Working from the underside of

the instrument panel, disconnect the

hose to the valve and the wires to the

relay and valve.

2.
Remove the bracket-

to-instrument panel attaching bolt and

swing the bracket downward.

3.
Remove the clevis pin that se-

cures the cable to the vacuum motor

rod.

4.
Disconnect the starter safety

switch wire at the connector.

5.
Remove the two motor-

to-bracket attaching screws and re-

move the motor, disconnecting the

hose to the solenoid.

Installation

1.
Position the motor on the
mounting bracket and the attaching

screws.

2.
Connect the control cable to the

vacuum motor rod with the clevis pin.

3.
Position the bracket to the in-

strument panel and install the attach-

ing bolt. Make all electrical and vacu-

um connections.

4.
Readjust the cable bracket to as-

sure full engagement of the locking

pawl when in driving position.

5.
Connect the hose to the vacuum

motor.

VACUUM MOTOR—

THUNDERBIRD

Removal

1.
Remove the lower finish panel.

2.
Disconnect the vacuum hose

from the solenoid valve. Disconnect

the electrical lead.

3.
Loosen the screws that attach

the bracket to the dash and lift the

bracket up; then, swing it down.

4.
Remove the clevis pin holding

the motor to the cable.

5.
Remove the two attaching

screws, then lift the motor from the

bracket.

C-CLAMP

PIVOT PIN

G 1462-A

FIG. 6—Installing Pivot Pinsprocarmanuals.com

03-05-06
Steering Columns And Linkage

03-05-06

Installation.

1.
Position the vacuum motor on

the bracket. Tighten the two attaching

screws.

2.
Connect the cable to the motor

with the clevis pin. Adjust the cable

bracket so the motor rod is fully ex-

tended, but not tight.

3.
Slide the vacuum motor as re-

quired to align the locking pawl rod

and vacuum motor. Retighten the two

vacuum motor attaching screws.

4.
Connect the vacuum hose to the

vacuum motor.

5.
Install the lower finish panel.

LOCKING LEVER

REPLACEMENT

Removal

1.
Remove the upper flange and

bearings from the column.

2.
Insert a 3
1/8-inch
bolt between

the lower ends of the locking levers

(Fig. 7) to relieve the tension from the

column release lever.

3.
Place the flange in a vise as

shown (Fig. 7) and remove the two re-

tainers with a screwdriver.

4.
Lift the column release lever

from the flange.

5.
Drive the locking lever retaining

pins from the flange with a small

drift.

6. Release the vise slowly to pre-

vent the levers from flying out.

LEVER RETAINING

PINS

3-1/8'
7.
Remove the levers, spring caps

and springs from the flange.

Installation

1.
Make sure that the rubber insu-

lators are in place in the upper flange.

2.
Position the springs, spring caps

and locking levers in the upper flange.

3.
Place the assembly in a vise and

compress the springs. Install new lever

retaining pins in the upper flange. The

pins should protrude from the sides of

the flange by .03 to .09 inch.

4.
Install a 3
1/8-inch
bolt between

the lower ends of the locking levers as

shown in Fig. 7.

5.
Make sure that the column re-

lease lever stop and spring is in place

in the upper flange, then position the

column release lever on the flange. In-

stall the two retainers.

6. Remove the 3
1/8-inch
bolt from

between the levers.

7.
Install the upper flange and

bearings in the steering column.

STEERING COLUMN

ALIGNMENT

THUNDERBIRD AND

CONTINENTAL MARK III

A condition of high shift or steering
efforts may be experienced caused by

improper alignment of the energy ab-

sorbing steering column. The fol-

lowing procedures outline the steps

necessary to correctly re-align either

fixed or tilt columns.

It is recommended that before at-

tempting realignment, the toe plate

(column retainer) to dash panel fas-

tener holes be inspected for a binding

or misaligned condition.

If the conditions described above

could be attributed to this area, file or

ream the dash panel holes for greater

clearance.

The column alignment procedures:

1.
Loosen the nuts retaining the toe

plate (column retainer) to the dash

panel (B in Fig. 8).

2.
Loosen to fingertight the bolt

and nut located on the toe plate re-

taining clamp (C in Fig. 8).

3.
Remove trim at instrument panel

to steering column mounting to ex-

pose retaining bolts.

4.
Loosen to fingertight {.he bolts

that support the column and bracket

against the instrument panel (D in

Fig. 8).

5.
Loosen to fingertight the bolts or

nuts which retain the column brackets

to the brake pedal support bracket

(E).

6. Loosen to fingertight the bolt

which controls lateral adjustment of

RETAINER

B

c

D

E

F
TORQUE VALUE

8-12 FT. LB.

3-5 FT. LB.

7.12 FT. LB.

7.12 FT. LB.

28-42 FT. LB.

G1536-A

FIG. 7—Removing or Installing

Locking Levers
FIG. 8—Steering Column Alignment Locations and Torque Specificationsprocarmanuals.com

03-05-08
Steering Columns And Linkage

03-05-08

tube.
In some instances the column

will shift into proper alignment when

the toe plate attaching nuts are loos-

ened. (Alignment is acceptable if a

.010 inch feeler blade can be passed

freely, completely around the area be-

tween the outer diameter of the steer-

ing shaft and the shift tube.) if the

misalignment condition can be attrib-

uted to this area, file or ream the dash

panel holes for greater clearance. If

the alignment is maintained after the

toe plate nuts and toe plate to column

clamp bolt and nut are torqued to the

8-12 ft-lb specification, no further ad-

justment is necessary.

4.
Remove instrument panel lower

trim panel. Vehicles equipped with a

combination radio stereo tape player

will require removal of the radio and

tape player assembly in order to gain

access to the upper R.H. steering col-

umn support bracket bolt.

5.
Loosen the seven bolts at the

steering column support bracket and

brake pedal support bracket.
6. Install a 3/16 inch diameter rod

spacer in the flex coupling to assure

proper clearance between upper and

lower steering shaft.

7.
Raise the vehicle, remove the

transmission splash shield, and visual-

ly align the column to center the

steering shaft in the column. Tighten

two toe plate attaching nuts sufficient-

ly to hold the column alignment (two

persons may be required for this oper-

ation).

8. Lower the vehicle.

9. Check the clearance between the

steering column support bracket and

the instrument panel bracket. It may

be necessary to add shims (Part Num-

ber MK-3054-A .060 inch thick, or

C3AZ-3054-A, .113 inch thick) be-

tween the support bracket and the in-

strument panel bracket to prevent

movement of the column when the

support bracket bolts are tightened.

10.
Loosen the two toe plate at-

taching nuts previously tightened. Re-

check steering column alignment. In
some instances it may be necessary to

enlarge the holes in the dash panel in

order to obtain proper column align-

ment.

11.
With the column properly al-

igned, torque the four toe plate at-

taching nuts to 4-9 ft-lbs.

12.
Torque the toe plate to steering

column clamp bolt to 3-5 ft-lbs.

13.
Recheck steering shaft to shift

tube alignment. A 0.10 inch feeler

blade should pass freely, completely

around the area between the outer di-

ameter of the steering shaft and shift-

er tube.

14.
Raise the vehicle.

15.
Adjust transmission shift link-

age.

16.
Install transmission splash

shield.

17.
Lower the vehicle.

18.
Install the radio stereo tape

player if so equipped.

19.
Install instrument panel lower

trim panel.

20.
Connect the battery.

REMOVAL AND INSTALLATION

STEERING COLUMN

FORD, MERCURY, METEOR

Removal

1.
Disconnect the battery cable

from the negative post.

2.
Disconnect the turn signal switch

wires at the connector.

3.
Disconnect the neutral start

switch and back-up light switch wires

from the switches.

4.
Disconnect the transmission con-

trol rod(s) from the lever(s) at the

lower end of the column.

5.
Remove the bolt that secures the

flex coupling to the steering gear.

6. Remove the nuts that secure the

column retainer and seal at the toe

plate (Fig. 11).

7.
Ford, Meteor: Remove the two

screws that secure the lower trim

shroud to the upper trim shroud. Re-

move the two shrouds.

Mercury: Remove the two screws

that secure the lower trim shroud to

the upper trim shroud. Remove the

top shroud Disconnect the ignition

switch light bulb. Remove the ignition

and light switch bezels and spring clip

and remove the lower shroud. Discon-
nect the light switch electrical connec-

tor block.

8. Remove the two screws that se-

cure the intermediate bracket to the

column lower bracket.

9. While supporting the steering

column, remove the two nuts that se-

cure the column lower bracket to the

instrument panel. Remove the brack-

ets.

10.
Lift the steering column and

wheel from the vehicle.

Installation

1.
Position the steering column in

the vehicle. Index the block tooth on

the steering gear shaft with the corre-

sponding slot on the flex coupling. In-

stall and tighten the flex coupling-

to-steering gear attaching bolt.

2.
Place the column upper bracket

and column lower bracket in position

on the column and install but do not

tighten the four attaching nuts.

3.
Install and tighten the two nuts

that secure the column lower bracket

to the instrument panel. Make certain

the column is properly positioned rela-

tive to the flex coupling input shaft

connection.

4.
Install and tighten the screws

that secure the intermediate bracket to

the column lower bracket.
5.
Tighten the four attaching nuts

at the upper and lower brackets and

the two nuts at the upper bracket to

instrument panel. The dial pointer (if

so equipped) should be adjusted to

coincide with the selector lever.

6. Install and tighten the nuts and

bolts that secure the column retainer

and seal at the toe plate. Make sure

the steering shaft is centered in the

column before tightening the nuts.

7.
Ford, Meteor: Install and tighten

the two screws that secure the lower

trim shroud to the upper trim shroud.

Mercury: Connect the light switch

harness block. Install the ignition and

light switch bezels. Connect the igni-

tion switch light bulb. Install the top

shroud and the two screws that secure

the lower trim shroud to the upper

shroud.

8. Connect the transmission control

rod(s) to the lever(s) at the lower end

of the column.

9. Connect the neutral start switch

and back-up light switch to their re-

spective terminals.

10.
Connect the turn signal switch

wires.

11.
Connect the negative battery

cable to the battery.

12.
Check the operation of the

steering tilt mechanism if so equipped

and the switches.procarmanuals.com