park assist FORD MUSTANG 1969 Volume One Chassis

02-02-35
Brake System

02-02-35

4.
Attach a wire to the end of the

cable to assist in routing new cable.

5.
Lower the vehicle.

6. Remove the parking brake front

cable ball retaining clip from the

clevis.

7.
Disconnect the cable ball from

the notch in the brake clevis.

8.. Remove the hairpin retainer and

remove the cable assembly from the

brake control assembly.

9. Pull the cable assembly up through

the opening in the floor and remove

the wire from the end of the cable.

Installation

Refer to Fig. 36.

1.
Connect the wire to the end of

the cable assembly and pull the cable

down through the opening in the

floor. Remove the wire.

2.
Connect the cable assembly to

the brake control assembly and in-

stall the hairpin retainer.

3.
Position the ball end of the

cable in the notch of the brake clevis.

4.
Raise the vehicle on a hoist.

5.
Pull the cable grommet into po-

sition and route the cable through

the access holes in the side rail and

under the fuel line.

6. Insert the cable into the body

bracket and install the hairpin re-

tainer.

7.
Position the spring, spring seat,

and equalizer on the cable and install

the two nuts.

8. Adjust the parking brake.

LINCOLN CONTINENTAL

Removal

1.
Raise the car on a hoist. Dis-

connect the parking brake cable from

the equalizer lever underneath the

car (Fig. 38).

2.
Remove the retaining clip at the

cable bracket, and disengage the cable

from the bracket (Fig. 38).

3.
Remove the supporting clip re-

taining bolts and remove the support

plate from the underbody.

4.
Lower the car on a hoist.

5.
With the parking brake in the

fully released position, disconnect the

cable at the control assembly.

6. Raise the vehicle on a hoist. Re-

move the left front fender apron

splash shield retaining bolts and the

splash shield.

7.
Remove the two bolts securing

the parking brake control to equaliz-

er cable bracket to the dash panel

and remove the cable from the vehicle.
Installation

1.
Route the parking brake control

to equalizer cable to the control as-

sembly and the equalizer, and install

the two bolts that retain the cable

to the dash panel (Fig. 38).

2.
Install the left fror%/ender apron

splash shield and the ^u attaching

bolts.

3.
Lower the vehicle.

4.
Connect the control cable to the

clevis on the control assembly.

5.
Raise the car on a hoist.

6. Position the supporting clip and

cable on the vehicle and install the

retaining bolts. Do not tighten the

bolts.
Position the cable armor ap-

proximately 1/2 inch to the right of

the clip (looking toward the rear of

the car) and tighten the retaining

bolts.

7.
Position the equalizer control

cable to the support bracket and in-

stall the retaining hairpin clip.

8. Connect the ball end of the con-

trol cable to the equalizer lever.

9. Adjust the parking brake linkage

(Part
2-1,
Section 2).

10.
Check the operation of the auto-

matic release mechanism.

PARKING BRAKE

ACTUATOR-TO-EQUALIZER

CABLE

FORD, MERCURY,

METEOR, THUNDERBIRD

AND CONTINENTAL

MARK III

Removal

Refer to Figs. 34 and 37.

1.
Raise the vehicle on a hoist.

2.
Remove the lock and adjusting

nut which retains the cable to the

equalizer.

3.
Remove the cable end from the

equalizer.

4.
Unhook the cable from the act-

uator, and remove from the vehicle. *

Installation

1.
Insert new cable end into act-

uator.

2.
Insert cable end into equalizer

and tighten the adjusting nut snug.

Install the lock nut.

3.
Adjust the parking brake cable

tension and check operation as out-

lined in Part
2-1,
Section 2.

4.
Lower the vehicle.
PARKING BRAKE EQUALIZER

TO REAR WHEEL CABLE

FORD, MERCURY,

METEOR, THUNDERBIRD

AND CONTINENTAL

MARK III

Removal

1.
Raise the vehicle and tffosen the

parking brake equalizer rod" adjusting

nut. Disconnect the equalizer from the

rear cables (Figs. 34 and 37).

2.
Compress the prongs on the left

cable-to-frame side member retainer

so the prong can pass through the

side-member. Remove the clip that at-

taches the left cable to the left lower

arm. Pull the cable thru the frame left

side member.

3.
Compress the prongs on the

right cable-to-frame side member re-

tainer bracket so the prong can pass

through the bracket. Remove the clips

retaining the right cable to the frame

crossmember.

4.
Remove the rear wheel cover and

wheel. Remove the three Tinnerman

nuts that hold the brake drum in place

and remove the drum.

5.
Working on the wheel side of the

rear brake, remove the automatic

brake adjuster spring. Compress the

prongs on the parking brake cable re-

tainer so that they can pass through

the hole in the brake backing plate.

Draw the cable retainer through the

hole.

6. With the spring tension off the

parking brake lever, lift the cable out

of the slot in the lever and remove the

cable through the backing plate hole.

Installation

1.
Pull enough of the parking brake

cable through the housing so that the

end of the cable may be inserted over

the slot in the parking brake lever on

the rear brake shoe.

2.
Pull the excess slack from the

cable, and insert the cable housing

into the brake backing plate access

hole so that the retainer prongs ex-

pand. The prongs must be securely

locked in place. Install the automatic

brake adjuster spring.

3.
Position the right hand cable and

the two retaining clips and screws on

the rear crossmember. Compress the

prongs on the right cable and position

the cable in the retaining bracket on

the frame side member. Be sure theprocarmanuals.com

03-01-02
Suspension — Steering, Wheels And Tires — General Service

03-01-02

1 TESTING

POWER STEERING-

PRELIMINARY TESTS

The following preliminary checks

should always be made before per-

forming any operations.

AIR BLEEDING

Air in the power steering system

(shown by bubbles in the fluid) should

be bled. After making sure that the

reservoir is filled to specification (the

fluid must be at normal operating

temperature when the check is made),

turn the steering wheel through its full

travel three or four times. Do not hold

the wheels against their stops. Re-

check the fluid level.

CHECK FLUID LEVEL

Run the engine until the fluid is at

normal operating temperature. Then

turn the steering wheel all the way to

the left and right several times, and

shut off the engine.

Check the fluid level in the power

steering reservoir. The level must show

on the cross hatching between the bot-

tom of the dipstick and the full mark

(Fig. 1). If the level is low, add

enough automatic transmission fluid

C1AZ-19582-A to raise the level to

the F mark on the dipstick. Do not

overfill the reservoir.

CHECK PUMP BELT

If the pump belt is broken, glazed,

or worn, replace it with a new belt.

Use only the specified type of belt.

Refer to Part 3-13 for belt adjustment

procedure.

CHECK FOR FLUID

LEAKS

With the engine idling, turn the

steering wheel from stop to stop sever-

al times. Check all possible leakage

points. Tighten all loose fittings, and

replace any damaged lines or defective

seats.

CHECK TURNING EFFORT

With the front wheels properly al-

igned and tire pressures correct, check

the effort required to turn the steering

wheel.
G 1508- A

FIG.
1—Power
Steering Pump

Dipstick

1.
With the vehicle on dry concrete,

set the parking brakes.

2.
With the engine warmed up and

running at idle speed, turn the steering

wheel to the left and right several

times to warm the fluid.

3.
Attach a pull scale to the rim of

the steering wheel. Measure the pull

required to turn the wheel one com-

plete revolution in each direction. The

effort required to rotate the steering

wheel should not exceed specifications

given in Part 3-13.

POWER STEERING PUMP FLOW

AND PRESSURE TESTS—

EXCEPT LINCOLN CONTINENTAL

AND CONTINENTAL MARK III

The power steering flow and pres-

sure tests will show whether the pump,

steering gear or power assist control

RETURN LINE

POWER

STEERING PUMP

Sr
valve is causing the trouble. Steps out-

lined below should be followed to de-

termine the cause of the trouble.

PUMP FLOW TEST

1.
Depending on the equipment

present on the vehicle (air condition-

ing, power brakes, standard transmis-

sion),
one of the following options

may be used to connect the pump

pressure and return hoses to the test

tool (T56L-3361O-D and T68L-

33610-A):

a. Disconnect the pressure and re-

turn lines at the power steering pump

(Fig. 2). Obtain a power steering re-

turn hose from stock and connect the

end with the fitting to the output fit-

ting of the tool using the
5/8-18
SAE

female, 1/4 N.P. thread male fitting

provided. The end of the stock hose

(without the fitting) should be con-

nected to the return tube of the pump.

Connect the pressure hose from the

tool to the outlet fitting of the pump.

b.
Disconnect the pressure line at

the pump and connect the pressure

line from the test tool to the outlet fit-

ting of the pump. Disconnect the re-

turn line at the gear and connect it to

the output fitting of the tool, using the

5/8-18
SAE female, 1/4 N.P. thread

male fitting provided.

2.
After installing the lines by the

most advantageous method, proceed

as follows:

3.
Open the manual valves A and B

fully (Fig. 2).

CALIBRATED FLOW

DETERMINING ORIFICE

PRESSURE LINE

FIG. 2—Power Steering Pump Test Circuit Diagram
PRESSURE GAGE

G1611-Aprocarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com