FORD MUSTANG 2003 Workshop Manual

5. Connect the toe link to the knuckle.
1. Position the toe link in the knuckle.
2. Install a new nut.
3. Install a new cotter pin.
6. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
Connect the shock absorber to the lower suspension arm and bushing and install the bolt and a
new nut.
7. Raise the suspension until the shock absorber is compressed to the previously established alignment mark (curb height). Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

8. Tighten the nut.
9. Make sure the marks on the cam bolt and the upper suspension arm and bushing made during
removal are aligned, and tighten the nut.
10. Lower the suspension and remove the jack stand.
11. Install the rear brake disc. For additional information, refer to Section 206 - 04 .
12. Install the parking brake cable and conduit into the knuckle. Klj . 7 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Connect the parking brake cable and conduit to the rear brake caliper and install the clip.
14. Connect the parking brake cable and conduit to the parking brake lever.
15.
CAUTION: The axle retainer must be tightened with the brakes applied and the
wheels off the ground to make sure of correct bearing seating. Failure to do so can
cause the retainer to loosen, causing extensive vehicle damage and loss of vehicle
control.
Lower the vehicle and apply the parking brake or service brakes.
16. Tighten the retainer.
17. Install the wheel and tire assembly. For additional information, refer to Section 204 - 04
18. Lower the vehicle.
19. Check the wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 - 00 . Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Klj . 9 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Toe Link —
Cobra
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
1. Raise the vehicle on a hoist. For additional information, refer to Section 100 - 02 .
2. Remove the wheel and tire assembly. For additional information, refer to Section 204 - 04 .
3. Remove the rear brake disc. For additional information, refer to Section 206 - 04 .
4. Support the lower suspension arm and bushing (5A649) with a jack stand.
5. Remove the nut and bolt and disconnect the shock absorber (18125) from the lower suspension arm and bushing. Discard the nut and bolt.
6. Remove and discard the cotter pin and nut.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Steering Arm Remover
211-
003 (T64P-9171- A) Klj . 1 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7.
CAUTION: Do not strike the toe link or the knuckle to disconnect the toe link. The
toe link or the knuckle can be damaged.
Using the special tool, disconnect the toe link (5K848) from the knuckle (5A968/5A969).
8. Remove the nut, bolt and the toe link. Discard the bolt and nut.
Installation 1. CAUTION: Make sure the hardened washer is installed between the lower
suspension arm and bushing and the shock absorber. Failure to do so can result in
damage and failure of the lower suspension arm and bushing.
NOTE: The toe link bolt and nuts are of a torque prevailing design. A new bolt and new nuts
must be installed.
NOTE: Use a new cotter pin.
To install, reverse the removal procedure. Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

2. Check wheel alignment. Adjust as necessary. For additional information, refer to
Section 204 -
00 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Klj . 4 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Spring —
Coil
Removal CAUTION: Suspension fasteners are critical parts because they affect performance of vital
components and systems and their failure can result in major service expense. A new part with
the same part number must be installed if installation becomes necessary. If substitution is
necessary, the part must be of the same finish and property class. Torque values must be used
as specified during reassembly to make sure of correct retention of these parts.
All vehicles
1. Mark the rear shock absorber (18125) relative to the protective sleeve with the vehicle in a static, level ground position (curb height).
2. Raise the vehicle. For additional information, refer to Section 100 - 02 .
3. Disconnect the anti- lock sensor wire.
SECTION 204-
02: Rear Suspension 2003 Mustang Workshop Manual Special Tool(s)
Hi-
Lift Jack
014- 00942 or Equivalent Klj . 1 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

4. Remove the bolt and the parking brake cable bracket. Discard the bolt.
Vehicles equipped with a 4.6L 2V engine 5. Remove the stabilizer bar (5A772). For additional information, refer to Stabilizer Bar in this
section.
All vehicles 6. Support the differential housing with a jack stand.
7. Position the special tool 014- 00942 under the rear lower suspension arm and bushing- to-axle
pivot bolt.
8. Remove and discard the pivot bolt and nut.
9. Remove the spring (5560). 1. Slowly lower the arm with the special tool 014- 00942.
2. Remove the rear spring and the rear spring insulators (5536). Installation Klj . 2 ba
52003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...