test G FORD MUSTANG 2003 Workshop Manual

GENERAL PROCEDURES
Evaporative Emission Repair Verification Drive Cycle
Drive Cycle Recommendations
NOTE:
The following procedure is designed to execute and complete the evaporative emission repair
verification drive cycle and to clear the Ford P1000, inspection and maintenance (I/M) readiness code.
When the ambient air temperature is below 4.4°C (40°F) or above 37.8°C (100°F), or the altitude is
above 2,438 meters (8,000 feet), the EVAP monitor will not run. If the P1000 must be cleared in these
conditions, the powertrain control module (PCM) must detect them once (twice on some applications)
before the EVAP monitor can be bypassed and the P1000 cleared. The EVAP bypassing procedure is
described in the following drive cycle.
1. Most OBD II monitors will complete more readily using a steady foot driving style during cruise or acceleration modes. Operating the throttle in a smooth fashion will minimize the time
necessary for monitor completion.
2. Fuel tank level should be between one- half and three-quarters full with three- quarters full being
the most desirable.
3. The evaporative monitor can only operate during the first 30 minutes of engine operation. When executing the procedure for this monitor, stay in part throttle mode and drive in a smooth
fashion to minimize fuel slosh.
Drive Cycle Preparation
NOTE: For best results, follow each of the following steps as accurately as possible.
4. NOTE: This step bypasses the engine soak timer and resets OBD II monitor status.
Install the scan tool. Turn the key ON with the engine OFF. Cycle the key off, then on. Select
the appropriate vehicle and engine qualifier. Clear all diagnostic trouble codes (DTCs) and carry
out a PCM reset.
5. Begin to monitor the following PIDs: ECT, EVAPDC, FLI (if available) and TP MODE. Press Diagnostic Data Link, PCM, PID/Data monitor and record, press trigger to select each PID, then
start.
6. Start the engine without returning the key to the OFF position.
Preparation for Monitor Entry
WARNING: Strict observance of posted speed limits and attention to driving conditions
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Special Tool(s)
Worldwide Diagnostic System
(WDS)
418-
F224,
New Generation STAR (NGS)
Tester
418- F052, or equivalent scan
tool Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Remove the EVAP canister from the canister bracket.
12. To install, reverse the removal procedure.
zCarry out a leak test. For additional information, refer to Evaporative Emission System Leak Test in this section.
z Carry out the evaporative emission repair verification drive cycle. For additional
information, refer to Evaporative Emission Repair Verification Drive Cycle in this section. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

10. To install, reverse the removal procedure.
zLeak test the system. For additional information, refer to Evaporative Emission System Leak Test in this section.
z Carry out the evaporative emission repair verification drive cycle. For additional
information, refer to Evaporative Emission Repair Verification Drive Cycle in this section. Klj . 3 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Fuel Vapor Control Tube Assembly Valve
Removal and Installation
1. Remove the fuel tank. For additional information, refer to Section 310 - 01 .
2. Remove the retainers.
3. NOTE: The fuel vapor vent valve, fuel vapor control valve and the in- line fuel tank pressure
sensor are repaired as a fuel vapor control valve tube assembly.
NOTE: It may be necessary to lubricate the fuel vapor control valve tube assembly grommets
with ESE- M00B144- B Merpol® or equivalent to assist in the removal procedure.
Remove the fuel vapor control valve tube assembly. 1. Loosen the fuel vapor vent valve.
2. Loosen the fuel vapor control valve.
3. Remove the fuel vapor control valve tube assembly.
4. NOTE: Lubricate all O- ring seals with MERPOL® O-Ring Seal Lubricant or equivalent meeting
Ford specification ESE-M99B144- B.
NOTE: New grommets are necessary when the fuel vapor control valve tube assembly is
removed.
To install, reverse the removal procedure.
zLeak test the system. For additional information, refer to Evaporative Emission System Leak Test in this section.
z Carry out the evaporative emission repair verification drive cycle. For additional
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Evaporative Emission Test Port
Removal and Installation
1. Disconnect the pin- type retainer.
2. Raise and support the vehicle. For additional information, refer to Section 100 - 02 .
3. Remove the RH front wheel. For additional information, refer to Section 204 - 04 .
4. Remove the RH front splash shield. 1. Remove the three screws.
2. Remove the five pin- type retainers.
5. Remove the evaporative emission test port by disconnecting at the EVAP canister purge outlet tube junction.
6. To install, reverse the removal procedure.
SECTION 303-
13: Evaporative Emissions 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
Leak test the system. For additional information, refer to Evaporative Emission System Leak Test in this section.
z Carry out the evaporative emission repair verification drive cycle. For additional
information, refer to Evaporative Emission Repair Verification Drive Cycle in this section. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Electronic Engine Controls
Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) manual.
SECTION 303-
14: Electronic Engine Controls 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Transmission linkage 23 17 —
Shift cable bracket 14 10 —
Transmission test plate bolts 10 — 89 Klj . 6 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Diagnostic Strategy
Troubleshooting an electronically controlled automatic transmission is simplified by using the proven
method of diagnosis. One of the most important things to remember is that there is a definite
procedure to follow.
NOTE:
Do not take any short cuts or assume that critical checks or adjustments have already been
made.
Follow the procedures as written to avoid missing critical components or steps.
To properly diagnose a concern have the following publications available:
zTransmission Reference Manual.
z Powertrain Control/Emissions Diagnosis (PC/ED) manual.
z TSBs and OASIS Messages.
z Wiring Diagram.
These publications provide the information required when diagnosing transmission concerns.
Use the Diagnostic Flow Chart as a guide and follow the steps as indicated.
Preliminary Inspection
zKnow and understand the customer's concern.
z Verify the concern by operating the vehicle.
z Check the fluid levels and condition.
z Check for non-factory add- on items.
z Check shift linkages for proper adjustment.
z Check TSBs and OASIS messages regarding the concern.
Diagnostics
zCarry out on- board diagnostic procedures key on engine off (KOEO) and key on engine running
(KOER).
z Record all diagnostic trouble codes (DTCs).
z Repair all non- transmission codes first.
z Repair all transmission codes second.
z Erase all continuous codes and attempt to repeat them.
z Repair all continuous codes.
z If only pass codes are obtained, refer to Diagnosis By Symptom for further information and
diagnosis.
Follow the diagnostic sequence to diagnose and repair the concern the first time. SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Diagnostic Flow Chart
SECTION 307-
01: Automatic Transaxle/Transmission 2003 Mustang Workshop Manual Diagnostic Flow Chart
z
Know and understand
the customer concerns
z Check the fluid level
and condition
z Verify the concern by
operating the vehicle
z Check for non- factory-
installed items and
verify correct installation
z Check the shift linkage
adjustments
z Check TSBs and
OASIS messages for
vehicle concerns
z Carry out quick test
both KOER and KOEO
z Record all codes
1) Did you record any
diagnostic trouble codes? Yes ·
REPAIR all hard diagnostic trouble codes. FOLLOW the
pinpoint tests. REFER to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual first, then this Workshop Manual. No ·
REFER to Diagnosis By Symptom in this section, then GO to
Step 5. 2) Are any continuous test
memory codes present? Yes ·
CLEAR codes and CARRY OUT drive cycle test. No ·
GO to Step 4. 3) Did the continuous test
memory codes reappear? Yes ·
REPAIR all continuous test memory codes. FOLLOW the
pinpoint tests. REFER to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual then the transmission reference
manual, then this workshop manual, then GO to Step 4. No ·
GO to Step 4. 4) Is the concern repaired? Yes ·
CARRY OUT the final quick test to verify that no diagnostic
trouble codes are present. CLEAR memory codes. No ·
REFER to Diagnosis By Symptom in this section.
5) Are there any electrical
concerns? Yes ·
INSTALL the scan tool and CARRY OUT the output state
control test, then GO to Step 6. No ·
REFER to the hydraulic and mechanical routine to diagnose
and REPAIR the concern, then GO to Step 7. 6) Was the transmission
concern corrected when the
scan tool was installed? Yes ·
REFER to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual, intermittent fault diagnosis section and use
the scan tool to diagnose cause of concern in the processor,
vehicle harness or external inputs (sensors or switches). Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2748/S3B~us~en~ ...