pinpoint test b FORD MUSTANG 2003 Workshop Manual

PINPOINT TEST D: THE ILLUMINATED ENTRY IS INOPERATIVE
WHEN USING THE REMOTE TRANSMITTER (coupe), map C907 (convertible), right hand vanity C906, left
hand vanity C978, or luggage compartment C4111.
z Measure the voltage between inoperative demand lamp,
Circuit 705 (LG/OG), harness side and ground.
z Is the voltage greater than 10 volts? No
REPAIR the circuit in
question. REPEAT the
self-
test. CLEAR the
DTCs. C9 CHECK CIRCUIT 1205 (BK) FOR OPEN AT INOPERATIVE
DEMAND LAMP z
Measure the resistance between inoperative demand lamp
Circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
INSTALL a new demand
lamp assembly. REPEAT
the self-
test. CLEAR the
DTCs.
No
REPAIR the circuit in
question. REPEAT the
self- test. CLEAR the
DTCs. Test Step Result / Action to Take
D1 CHECK THE REMOTE TRANSMITTER
INPUT TO THE GEM z
Remove the ignition key from the ignition.
z Depress the lock and then the unlock
buttons on the remote transmitter.
z Do the doors lock when the lock button
is depressed and unlock when the
unlock button is depressed? Yes
GO to
D2 .
No
REFER to Section 501 - 14B .
D2 CHECK OPERATION OF ILLUMINATED
ENTRY WITHOUT REMOTE TRANSMITTER z
Open the driver door.
z Do the courtesy lamps illuminate? Yes
INSTALL a new GEM. For additional
information, REFER to
Section 419 - 10 .
REPEAT the self- test. CLEAR the DTCs.
No
GO to Pinpoint Test B . Klj . 14 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST E: THE BATTERY SAVER DOES NOT DEACTIVATE
AFTER TIMEOUT
Test Step Result / Action to Take
E1 CHECK THE GEM CONTROL OF THE BATTERY SAVER
FUNCTION — TRIGGER THE GEM ACTIVE COMMAND BATT
SAVR ON z
Trigger the GEM active command BATT SAVR ON and then
OFF.
z Do the courtesy lamps illuminate and turn off when the
GEM active command BATT SAVR is triggered ON and
OFF? Yes
INSTALL a new GEM.
For additional
information, REFER to
Section 419
- 10 .
REPEAT the self- test.
CLEAR the DTCs.
No
GO to E2 .
E2 CHECK CIRCUITS 1034 (BK/WH), AND 705 (LG/OG), FOR
SHORT TO BATTERY z
Disconnect: GEM C201c.
z Measure the voltage between GEM C292 Pin 3, Circuit 1034
(BK/WH), harness side and ground; and between GEM C292
Pin 4, Circuit 705 (LG/OG), harness side and ground.
z Is the voltage greater than 10 volts? Yes
REPAIR the circuit in
question. REPEAT the
self-
test. CLEAR the
DTCs.
No
INSTALL a new GEM.
For additional
information, REFER to
Section 419 - 10 .
REPEAT the self- test.
CLEAR the DTCs. Klj . 15 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

next step. For additional information, refer to
Section 417 - 01 .
4. Verify the parking brake control is fully released.
5. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
6. If the concern is not visually evident, verify the symptom and refer to the Symptom Chart.
Symptom Chart
Pinpoint Tests
PINPOINT TEST A: THE DAYTIME RUNNING LAMPS ARE
INOPERATIVE Symptom Chart Condition
Possible Sources Action
z The daytime running lamps are
inoperative z
BJB Maxi- Fuse
FOG+DRL (20A).
z Circuitry.
z Parking brake
signal switch and
bracket.
z DRL module. z
GO to
Pinpoint Test A .
z The daytime running lamps are
on with the parking brake set z
Circuitry.
z Parking brake
signal switch and
bracket.
z DRL module. z
GO to
Pinpoint Test B .
z The daytime running lamps are
on with the ignition switch off z
Circuitry.
z Ignition switch.
z DRL module. z
GO to
Pinpoint Test C .
z The low beam headlamps are on
at full intensity in DRL mode z
Circuitry.
z Headlamp switch.
z DRL module. z
GO to
Pinpoint Test D .
z The low beam headlamps are on
at reduced intensity with the
headlamp switch on z
Circuitry.
z Headlamp switch. z
REFER to
Section 417 -
01 .
Test Step Result / Action to Take
A1 CHECK THE PARKING BRAKE SWITCH SIGNAL
CIRCUIT TO THE DRL MODULE FOR SHORT TO GROUND NOTE:
Verify the parking brake control is fully released
for this step.
z Key in OFF position.
z Disconnect: DRL Module C1030.
z Measure the resistance between DRL module C1030 Pin
6, Circuit 22 (LB/BK), harness side and ground. Yes
GO to
A3 .
No
GO to A2 . Klj . 2 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST B: THE DAYTIME RUNNING LAMPS ARE ON WITH
THE PARKING BRAKE SET z
Is the voltage greater than 10 volts? A5 CHECK THE DRL MODULE GROUND —
CIRCUIT 1205
(BK) z
Measure the resistance between DRL module C1030 Pin
4, Circuit 1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
GO to
A6 .
No
REPAIR the circuit. TEST the
system for normal operation. A6 CHECK THE HIGH BEAM DISABLE INPUT CIRCUIT FOR
SHORT TO BATTERY — CIRCUIT 12 (LG/BK) z
Measure the voltage between DRL module C1030 Pin 5,
Circuit 12 (LG/BK), harness side and ground.
z Is voltage indicated? Yes
REPAIR the circuit. TEST the
system for normal operation.
No
INSTALL a new DRL module.
REFER to
Module — Daytime
Running Lamps (DRL) . TEST
the system for normal
operation. Test Step Result / Action to Take
B1 CHECK THE PARKING BRAKE SWITCH
z
Key in OFF position.
z Disconnect: Parking Brake Switch C306.
z Connect a 10A fused jumper wire between parking brake
switch C306, Circuit 22 (LB/BK), harness side and ground.
z Key in ON position. Yes
INSTALL a new parking
brake signal switch and
bracket. TEST the system
for normal operation.
No
GO to
B2 . Klj . 4 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST C: THE DAYTIME RUNNING LAMPS ARE ON WITH
THE IGNITION SWITCH OFF z
Do the DRL turn off? B2 CHECK THE PARKING BRAKE SWITCH SIGNAL CIRCUIT
z
Key in OFF position.
z Disconnect: DRL Module C1030.
z Measure the resistance between parking brake switch C306,
Circuit 22 (LB/BK), harness side and DRL module C1030 Pin
6, Circuit 22 (LB/BK), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new DRL
module. REFER to
Module
— Daytime
Running Lamps (DRL) .
TEST the system for
normal operation.
No
REPAIR the circuit. TEST
the system for normal
operation. Test Step Result / Action to Take
C1 CHECK THE IGNITION SWITCH INPUT TO THE DRL
MODULE FOR VOLTAGE z
Key in OFF position.
z Disconnect: DRL Module C1030.
z Measure the voltage between DRL module C1030 Pin 3,
Circuit 298 (VT/OG), harness side and ground.
z Is voltage indicated? Yes
GO to
C2 .
No
INSTALL a new DRL module.
REFER to Module — Daytime
Running Lamps (DRL) . TEST
the system for normal
operation. C2 CHECK THE IGNITION SWITCH
z
Check the ignition switch; refer to the Wiring Diagrams
Cell 149.
z Is the ignition switch OK? Yes
REPAIR Circuit 298 (VT/OG)
for short to battery. TEST the
system for normal operation.
No
INSTALL a new ignition switch.
REFER to
Section 211 - 05 .
TEST the system for normal
operation. Klj . 5 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST D: THE LOW BEAM HEADLAMPS ARE ON AT FULL
INTENSITY IN DRL MODE
Test Step Result / Action to Take
D1 CHECK THE LOW BEAM
HEADLAMPS INPUT z
Disconnect: DRL Module
C1030.
z Are the low beam
headlamps still on at full
intensity? Yes
REFER to
Section 417 - 01 .
No
INSTALL a new DRL module. REFER to Module —
Daytime Running Lamps (DRL) . TEST the system for
normal operation. Klj . 6 ba
62003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

The generic electronic module (GEM) is on the ISO 9141 network. The GEM module controls a variety
of systems including one touch down windows, wipers, perimeter anti-
theft, and warning chimes. For
additional information, refer to Section 419 - 10 .
The anti- lock brake control module communicates over the ISO 9141 communication network when
not equipped with traction control and communicates over the SCP communication network when it is
equipped with the traction control option. The anti- lock brake control module controls the brake
pressure to the four wheels to keep the vehicle under control while braking. For additional information
on anti- lock brake control module without traction control, refer to Section 206 - 09A . For additional
information on anti- lock brake control module with traction control, refer to Section 206 - 09B .
The instrument cluster is on the SCP communication network. The instrument cluster displays driver
information. The instrument cluster incorporates the PATS control module functions. For additional
information on the PATS system, refer to Section 419 - 01 . For additional information on the instrument
cluster, refer to Section 413 - 01 .
Inspection and Verification 1. Verify the customer concern.
2. Visually inspect for obvious signs of electrical damage.
3. If the concern remains after the inspection, connect diagnostic tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from diagnostic
tool menu. If diagnostic tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
z check that the correct version of the program card is installed.
z check the connections to the vehicle.
z check the ignition switch position.
If the diagnostic tool still does not communicate with the vehicle, go to Pinpoint Test H. 4. Go to Pinpoint Test PC.
System Precheck Visual Inspection Chart Electrical
z
Central junction box (CJB) Fuse 31 (5A)
z Damaged wiring harness
z Loose or corroded connections
z Anti- lock brake control module without traction control (optional)
z Anti- lock brake control module with traction control (optional)
z Generic electronic module (GEM)
z Restraint control module (RCM)
z Powertrain control module (PCM)
z Instrument cluster Klj . 2 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST PC: DATA LINK DIAGNOSTICS NETWORK TEST
Symptom Chart
Test Step Result / Action to Take
PC1 DATA LINK
DIAGNOSTICS NETWORK
TEST z
Run the Data Link
Diagnostics Network
Test.
z Is SYSTEM PASSED
obtained? Yes
Test PASSED. RETURN to the Symptom Chart of the section
for the module in question.
No
If no response from the diagnostic tool, GO to
Pinpoint Test H .
If CKT70=ALL ECUS NO RESP / NOT EQUIP, GO to Pinpoint Test F .
If CKT914 or CKT915=ALL ECUS NO RESP / NOT EQUIP,
GO to Pinpoint Test G .
If CKT70, CKT914, or CKT915=SOME ECUS NO RESP/NOT
EQUIP, REFER to Symptom Chart.
If the module in question is NO RESPONSE ON CKT914
(BUS+), or NO RESPONSE ON CKT915 (BUS-), REFER to
Symptom Chart.
If the module in question is NO RESPONSE/NOT EQUIPPED,
REFER to Symptom Chart.
Symptom Chart Condition
Possible Sources Action
z The module does not
respond to the diagnostic
tool — anti-lock brake control
module z
Wire or connection in SCP
communication network
(with traction control).
z Wire or connection in ISO
9141 communication
network (without traction
control).
z Anti- lock brake control
module without traction
control (optional).
z Anti- lock brake control
module with traction
control (optional). z
GO to
Pinpoint Test A .
z The module does not
respond to the diagnostic
tool — generic electronic
module (GEM) z
Wire or connection in ISO
9141 communication
network.
z GEM. z
GO to
Pinpoint Test B .
z The module does not
respond to the diagnostic
tool — restraint control
module (RCM) z
Wire or connection in ISO
9141 communication
network.
z RCM. z
GO to
Pinpoint Test C .
z The module does not
respond to the diagnostic z
Wire or connection in SCP
communication network. z
GO to
Pinpoint Klj . 3 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Pinpoint Tests
CAUTION: Be careful when probing the CJB, battery junction box (BJB) or any
connectors. Damage will result to the connector receptacle if the probe or terminal being used
is too large.
CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to
these charges, damage may result.
NOTE: If DTCs are recorded and the symptom is not present when carrying out the pinpoint tests, an
intermittent concern may be the cause. Always check for loose connections and corroded pins.
PINPOINT TEST A: THE MODULE DOES NOT RESPOND TO THE
DIAGNOSTIC TOOL — ANTI-LOCK BRAKE CONTROL MODULE tool —
instrument cluster zInstrument cluster. Test D .
z The module does not
respond to the diagnostic
tool — powertrain control
module (PCM) z
Wire or connection in SCP
communication network.
z PCM. z
GO to
Pinpoint Test E .
z No module/network
communication — ISO 9141
network z
Wire or connection in ISO
9141 communication
network.
z ISO 9141 networked
modules. z
GO to
Pinpoint Test F .
z No module/network
communication — SCP
network z
Wire or connection in SCP
communication network.
z SCP networked modules. z
GO to
Pinpoint Test G .
z No module/network
communication — no power
to the diagnostic tool z
CJB Fuse 31 (5A).
z DLC pins.
z Scan tool.
z Circuitry. z
GO to
Pinpoint Test H .
Test Step Result / Action to Take
A1 CHECK THE VEHICLE FOR TRACTION CONTROL
z
Check the vehicle for a traction control disable switch.
z Is a traction control disable switch present? Yes
GO to
A2 .
No
GO to A9 .
A2 CHECK ANTI-
LOCK BRAKE CONTROL MODULE C141
FOR DAMAGE z
Key in OFF position.
z Disconnect: Anti- Lock Brake Control Module C135.
z Inspect the anti- lock brake control module C135 for
damage; repair as necessary.
z Connect: Anti- Lock Brake Control Module C135.
z Connect the diagnostic tool.
z Key in ON position.
z Enter the following diagnostic mode on the diagnostic
tool: Diagnostic Data Link. Yes
GO to
A3 .
No
GO to A6 . Klj . 4 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST B: THE MODULE DOES NOT RESPOND TO THE
DIAGNOSTIC TOOL —
GENERIC ELECTRONIC MODULE (GEM)
PINPOINT TEST C: THE MODULE DOES NOT RESPOND TO THE
DIAGNOSTIC TOOL — RESTRAINT CONTROL MODULE (RCM) z
Measure the resistance between in- line C314 Pin 1,
Circuit 70 (LB/WH), harness side and DLC C257 Pin 7,
Circuit 70 (LB/WH), harness side.
z Is the resistance less than 5 ohms? between in-
line C314 and in- line
C140. TEST the system for
normal operation.
No
REPAIR Circuit 70 (LB/WH)
between in- line C314 and DLC
C251. TEST the system for
normal operation. Test Step Result / Action to Take
B1 CHECK FOR OPEN BETWEEN THE DLC C251 AND GEM
C201e z
Key in OFF position.
z Disconnect: GEM C201e.
z Inspect GEM C201e for damage, repair as necessary.
z Measure the resistance between GEM C201e Pin 6, Circuit
70 (LB/WH), harness side and DLC C251 Pin 7, Circuit 70
(LB/WH), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 - 10 .
TEST the system for normal
operation.
No
REPAIR Circuit 70 (LB/WH)
between the GEM C201e
and DLC C251. TEST the
system for normal
operation. Test Step Result / Action to Take
C1 CHECK CIRCUIT 70 (LB/WH) FOR OPEN
z
Key in OFF position.
z Inspect the DLC C251 and diagnostic tool terminal for
damage; repair as necessary.
z Deactivate the air bag system. Refer to Section 501 - 20B .
z Disconnect: RCM C2041.
z Inspect RCM C2041 for damage, repair as necessary.
z Measure the resistance between DLC C251 Pin 7, Circuit 70 Yes
INSTALL a new RCM.
REFER to
Section 501 -
20B . TEST the system for
normal operation.
No Klj . 8 ba
212003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...