timing FORD MUSTANG 2003 Owner's Manual

N806155 Bolt (2 req'd)
92 6C315 Crankshaft position sensor
93 N806300 Stud bolt (5 req'd)
94 6C086 Engine front cover
95 N806155 Bolt
96 6B288 Camshaft position sensor
97 N606543 Bolt (4 req'd)
98 6L266 Timing chain tensioner
99 6268 Timing chain belt
100 6K297 Timing chain cover
101 6M269 Timing chain tensioner
102 6L253 Timing chain tensioner arm
103 N806184 Bolt (3 req'd)
104 19D629 A/C compressor
105 8501 Water pump
106 N806177 Bolt (4 req'd)
107 N806183 Bolt (4 req'd)
108 6621 Oil pump
109 N806201 Woodruff key
110 6333 Crankshaft main bearing (5 req'd)
111 6A341 Crankshaft thrust washer (3 req'd)
112 6C357 Crankshaft main bearing side bolt (10 req'd)
113 6010 Cylinder block
114 9439 Intake manifold gasket (2 req'd)
115 6083 Head gasket
116 6505 Exhaust valve (8 req'd)
117 6507 Intake valve (8 req'd)
118 87838 Pipe plug (8 req'd)
119 12405 Spark plug (8 req'd)
120 6F087 Dowel
121 9431 Exhaust manifold
122 6C501 Valve tappet (16 req'd)
123 6529 Rocker arm (16 req'd)
124 6049 Cylinder head, RH
125 W701681 Stud (8 req'd)
126 9Y431 Exhaust manifold gasket
127 9F485 EGR valve tube to manifold connector
128 W701706 Nut (8 req'd)
129 181198A Engine lifting eye
130 6A517 Valve stem seal (16 req'd)
131 6513 Valve spring (16 req'd)
132 Klj . 6 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

6514 Valve spring retainer (16 req'd)
133 6518 Valve spring retainer key (32 req'd)
134 6065 Cylinder head bolt (20 req'd)
135 6C255 Camshaft
136 9J434 EGR transducer
137 N807309 Bolt (2 req'd)
138 N806139 Bolt
139 8620 Drive belt
140 N806165 Washer
141 6316 Crankshaft pulley
142 8A528 Water pump pulley
143 6700 Crankshaft front seal
144 N808793 Stud bolt (2 req'd)
145 N806177 Bolt (6 req'd)
146 N806176 Bolt (3 req'd)
147 3A674 Power steering pump
148 12A227 Ignition pulse ring
149 6306 Crankshaft sprocket (2 req'd)
150 6268 Timing chain/belt
151 6K297 Timing chain guide
152 N804958 Bolt (4 req'd)
153 6A338 Crankshaft main bearing (4 req'd)
154 6A346 Crankshaft main bearing cap dowel pin (10 req'd)
155 6345 Crankshaft main bearing cap bolt (9 req'd)
156 N806155 Bolt (2 req'd)
157 W701240 Bolt (16 req'd)
158 6675 Oil pan
159 6710 Oil pan gasket
160 N605904 Bolt
161 6622 Oil pump screen cover and tube
162 N806180 Spacer
163 6K258 Crankshaft main bearing cap stud
164 6325 Main bearing cap (5 req'd)
165 6A339 Crankshaft thrust main bearing
166 N602549 Bolt
167 6303 Crankshaft
168 7563 Clutch pressure plate
169 7550 Clutch disc
170 N808139 Bolt (6 req'd)
171 6375 Flywheel (manual transmission)
172 N811363 Bolt (2 req'd)
173 Klj . 7 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Timing Drive Components
Removal CAUTION: Since the engine is not free- wheeling, timing procedures must be followed
exactly or piston and valve damage can occur.
1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this
section.
2. Remove the crankshaft sensor ring from the crankshaft. 3. Disconnect the eight ignition coil electrical connectors. SECTION 303-
01B: Engine — 4.6L (2V) 2003 Mustang Workshop Manual Special Tool(s)
Compressor, Valve Spring
303-
567 (T97P-6565- AH) Holding Tool, Crankshaft
303-
448 (T93P-6303- A) Aligner, Camshaft Position
303-
557 (T96T-6256- B) Klj . 1 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

7. Remove the bolts and the LH timing chain tensioner.
8. Remove the bolts and the RH timing chain tensioner. Klj . 3 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Remove the LH and the RH timing chain tensioner arm from the dowel pins.
10. Remove the timing chains and the crankshaft sprocket.
11. Remove the timing chain guides. 1. Remove the bolts.
2. Remove the LH timing chain guide.
3. Remove the bolts.
4. Remove the RH timing chain guide. Klj . 4 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

1.
CAUTION: The timing chain procedures must be followed exactly or damage to the
valve and pistons will result.
Compress the tensioner plunger, using an edge of a vise.
2. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
3. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
4. If the copper links are not visible, mark one link on one end and one link on the other end, and use as timing marks. Klj . 6 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Install the crankshaft sprocket, making sure the flange faces forward.
10. Install the timing chain guide. 1. Position the LH timing chain guide.
2. Install and tighten the LH bolts.
3. Position the RH timing chain guide.
4. Install and tighten the RH bolts.
11. Install the timing chains. zInstall the LH (inner) timing chain on the crankshaft sprocket, aligning the copper link with
the dot on the crankshaft sprocket.
z Install the LH (inner) timing chain on the camshaft sprocket, aligning the copper link with
the dot on the camshaft sprocket.
z Install the RH (outer) timing chain on the crankshaft sprocket, aligning the copper link
with the dot on the crankshaft sprocket.
z Install the RH (outer) timing chain on the camshaft sprocket, aligning the copper link with
the dot on the camshaft sprocket. Klj . 8 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

12. Make sure that the copper (marked) chain links are lined up with the dots on the crankshaft
sprocket and the camshaft sprockets.
13. NOTE: The LH timing chain tensioner arm has a bump near the dowel hole, for identification.
Position the LH and the RH timing chain tensioner arm on the dowel pins. Klj . 9 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

14. Position the RH timing chain tensioner and install the bolts.
15. Position the LH timing chain tensioner and install the bolts. Klj . 10 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

16. Remove the paper clip from the RH and the LH timing chain tensioners.
17.
NOTE: Rotate the camshaft to the base circle of the camshaft lobe before installing the roller
followers.
NOTE: Keep all the roller followers in order when installing.
Using the special tool, install the 16 roller followers.
18. Install the eight spark plugs. Klj . 11 ba
132003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...