FORD MUSTANG 2003 Workshop Manual

GENERAL PROCEDURES
Safety Belt Tongue Rotated on Belt
1. Grasp the belt tongue and pull the belt webbing down to form a loop through the upper (longer and narrower) slot in the tongue.
2. Rotate and fold the belt webbing over itself within the slot to remove the twist.
3. Pull the excess belt webbing back through the upper slot in the belt tongue.
4. Grasp the belt tongue and pull the belt webbing up to form a loop through the low slot in the tongue.
5. Rotate and fold the belt webbing over itself within the slot to remove the twist.
6. Pull the excess belt webbing through the slot.
7. NOTE: Dual slot tongue shown; single slot tongue is similar.
The safety belt tongue should face inward when completed.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Front Seat Safety Belt, Coupe
Removal 1. Remove the quarter trim panel (31012). For additional information, refer to Section 501 - 05 .
2. Using the special tool, remove the bolt and the safety belt retractor. zRemove the mastic seal.
3. Using the special tool, remove the safety belt anchor bolt.
4. Using the special tool, remove the D- ring bolt.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Installation
NOTE:
Make sure the retractor tongue faces inboard.
NOTE: Make sure the safety belt is not twisted.
1. The shipping clip must remain attached prior to the installation of the retractor into the vehicle.The clip must be removed after the retractor is installed.
2. Position the safety belt anchor. Using the special tool, install the safety belt bolt.
3. Install a new mastic seal around the safety belt retractor before installing the retractor in the vehicle.
4. Position the safety belt retractor. Using the special tool, install the bolt. Klj . 2 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

5. Using the special tool, install the D-
ring bolt.
6. Install the quarter trim panel. For additional information, refer to Section 501 - 05 .
7. The shoulder belt must pass through the belt holder on the top of the seatback.
8. Check the active restraint system for correct operation. Klj . 3 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Klj . 4 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Front Seat Safety Belt, Convertible
Removal 1. Remove the quarter trim panel (31012). For additional information, refer to Section 501 - 05 .
2. Remove the nut and bolts and safety belt retractor.
Installation
NOTE: Make sure the safety belt is not twisted.
1. The shipping clip must remain attached prior to the installation of the retractor into the vehicle. The clip must be removed after the retractor is installed. 2. Position the safety belt retractor. Install the nut and bolts. SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

3. The shoulder belt must pass through the belt holder on the top of the seatback.
4. Install the quarter trim panel. For additional information, refer to
Section 501 - 05 .
5. Check the active restraint system for correct operation. Klj . 2 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

REMOVAL AND INSTALLATION
Retractor —
Rear Seat Safety Belt, Coupe
Removal 1. Remove the quarter trim panel (31012) and the angel wing trim. For additional information, refer to Section 501 - 05 .
2. Using the special tool, remove the D- ring bolt.
3. Using the special tool, remove the bolt and the safety belt retractor (611B68).
4. Remove the bolt.
SECTION 501-
20A: Safety Belt System 2003 Mustang Workshop Manual Special Tool(s)
Torx Bit, Safety Belt Bolt
501-
010 (T77L-2100- A) Klj . 1 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Installation
NOTE:
Make sure the safety belt is not twisted when inserting it in the quarter trim panel.
1. Install the bolt.
2. Using the special tool, install the safety belt retractor and the bolt.
3. Using the special tool, install the D- ring bolt. Klj . 2 ba
32003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...