light GEELY CK 2008 Owner's Guide

216IV. FRONT FOG LAMP BEAM ADJUSTMENT1. Adjust the tire inflation pressure with the standard value
2. Start the engine
3. Turn the fog lamp switch ON
4. Adjust the fog lamp beam.
Turn the bolt A for adjusting fog lamp beam in vertical direction.
NOTES:
Turn the screwdriver counter-clockwise to make the light beam up, clockwise make the light beam down.

225Section 3 Audio System InspectionI TroubleshootingSymptom
Suspected Area
1. Ra dio a ssembly c ircuit fa ulty
2. Ra dio a ssembly
1. Ra dio a ssembly bac klight te rmina l
2. Ra dio a ssembly
1. Spea ker c irc uit
2. Ra dio a ssembly powe r c ircuit faulty
3. Ra dio a ssembly
1. Spea ker c irc uit
2. Ra dio a ssembly powe r c ircuit faulty
3. Ra dio a ssembly
1. Ante nna c ircuit
2. Ra dio a ssembly
1. Ta pe
2. Ra dio a ssembly powe r c ircuit faulty
3. Ra dio a ssembly
1. Ta pe
2. Ra dio a ssembly
1. Ta pe
2. Ra dio a ssembly
1. Ta pe
2. Ra dio a ssembly
1. Wire betwe en CD box a nd main unit
2. CD P la ye r ma in unit pow e r supply c irc uit fa ult
3. CD box
4. CD Player main unit
1. Wire betwe en CD box a nd main unit
2. CD box
3. CD
4. CD Player main unit
1. Wire betwe en CD box a nd main unit
2. CD box
3. CD
4. CD PLAYER main unit
1. Wire betwe en CD box a nd main unit
2. CD box
1. CD box
2. CD box installa tion Sound quality poor only when pla ying CD
(Volume faint)
CD sound jump Tape ja mme d, ma lfunc tion with tape
speed or auto-reverse
CD could not be inserted or ejected after
ins e r t e d.
P owe r c oming in, but CD playe r not
operating.
CD ca n not be ta ke n out Una ble to re ce ive ra dio broa dca st (poor
re ce ption)
The c a ssette c ould not be inserted or
playe d
Cassette tape will not be ejected
Sound qua lity poor only whe n playing
cassette tape Ra dio not operating when powe r switch
turned to “ON”.
The radio ba cklight doe s not light up with
t he illumina t ion s w it c h O N
Spe ake r soundless in all modes
Sound qua lity poor in all mode s (Volume
faint)

2272. The radio backlight does not light up with the illumination switch ON
Wiring Diagram
(1) Check radio assembly (TAIL)
Check the voltage between terminals under each operating condition as shown in the table below.
Standard:
Abnormal:Repair or replace wire harness and connector
Normal:Check and replace radio assemblyMain Fuse BoxRadio and CDFusible Link Box
BatteryLight
Control
Switch
BatteryTeste r Connec tion Condition Sta nda rd Sta tus
TAIL - GND Combined Switch (Light switc h) 10～
14V

2283. Speaker soundless in all modes
Wiring Diagram
(1) Check LCD (Liquid Crystal Display) illumination
1Turn ignition switch to ACC
2Connect radio assembly continuity
3Switch on position lamp
Standard: Radio assembly LCD light goes on
Abnormal:Go to Step (7)
Normal:Go to Next Step
(2) Control volume and adjust volume balance
yOperate the radio assembly to adjust volume balance and find soundless speaker
Check and replace the radio assembly if all the speakers are soundless
Check and replace the soundless speakers if some of the speakers are soundlessMain Fuse BoxRadio and CDIgnition switchFusible Link BoxBatteryLeft Rear SpeakerRight Rear SpeakerLeft tweeter SpeakerRight tweeter SpeakerLeft Front Speaker
Right Front Speaker

242Chapter 7
SRS (Supplemental Restraint System)Section 1 SRS-General InformationI. PRECAUTIONFor safe reasons, read the following precautions before starting any operation.
1. When servicing the SRS, correct sequence and items are described in the following chapter.
2. Instruments and special tools recommended in this chapter shall be used for operation.
3. When servicing the following components, replace them with the new ones if there is a failure.
(1) SRS ECU
(2) Clock Spring Module
(3) Driver Airbag Module
(4) Passenger Airbag Assembly (Option)
4. If there is any abnormality in the wire harness of the SRS, replace it with a new one. Correct or replace the
abnormal wire harness in accordance with Table 1.
Figure 1 (Table 1)No De signation De scription
1 Belt-pretensioner, Driver, Low Seat belt pretensioner, driver side, low position
2 Belt-pretensioner, Driver, High Seat belt pretensioner, driver side, high position
3 Belt-pretensioner, Passenger, High Seat belt pretensioner, passenger side, high position
4 Belt-pretensioner, Passenger, Low Seat belt pretensioner, passenger side, low position
5 IGN Battery voltage
6 GND Ground-ground w ire
7 WL Airbag w arning light
9 K Diagnostic serial data I/O (K line)
10 DAB Hi Driver airbag, high positionE C U T e r mina l D e s c r ipt ion

2435. Servicing operation shall be carried out 60s after the negative
(-) terminal cable is disconnected from the battery. In addition,
the disconnected negative (-) terminal cable shall be protected
with insulating tape for insulation.
In order to deploy an airbag within a certain time period after the
battery is disconnected, condenser in the ECU shall retain some
electrical energy. Otherwise, it could lead to a serious accident
because of the unexpected deployment of airbag.
6. During spray paint work, ECU, airbag assembly, clock spring
assembly, etc shall be removed and kept in place to avoid the effects of overheat. (Over 93¡æ)
7. When the SRS is serviced, a diagnostic scan meter is used to clear the DTC to enable the normal work of
the warning light.1 1 D AB Lo D r iv er a ir b ag , lo w p o s it io n
13 (Option) PAB Hi Passenger airbag, high position
14 (Option) PAB Lo Passenger airbag, low position
20Passenger Airbag Deactivation
Indic atorPassenger airbag deac tivation indic ator light
27PPD/ Passenger Airbag
Deac tivation Sw itch, HighPassenger airbag deac tivation sw itc h, high position
30 Crash Output Crash outputInsulating TapeBatteryCableDriver Side
Warning LampPassenger Side
Warning LampDriver Seat Inflation
Element & AirbagCrash Sensor &
Diagnostic ModuleFront/RH Inflation
Element & Airbag

244II. TEST INSTRUMENTS
III. TROUBLESHOOTING1. Basic process of trouble diagnosis
yDTC of the present fault may coexist with that of the history fault.
NOTICE:
yAfter the new SRS ECU is installed, the warning light of the SRS, with the ignition switch ON, will be on
for 6s and then go out permanently, indicating SRS works normal. In this case, no service is needed.
Otherwise, system diagnosis and service shall be carried out.
y If with the ignition switch ON, the warning light of the SRS is not on, the relevant circuits of the warning
light shall be serviced. Then go on with the operation and enable it to work.
2. Check SRS warning light
(1) Turn the ignition switch ON and find out whether the warning light is on.
(2) Six seconds after the process of ON-OFF, confirm that the warning light goes out permanently.
(3) Otherwise, diagnosis and checking have to be involved in.
3. System Diagnosis
The SRS ECU (HAE2.5) will perform a series of circular diagnostic tests to check the readiness of the SRS
functions. This test can avoid unexpected explosion of the restrain system and in the same time ensure the
necessary explosion in a crash. If a trouble is detected, the SRS ECU (HAE2.5) will store a proper DTC and
turn on the warning light indicating a trouble for service.Instrument Designation Usage
Check system troubles of the SRS, and
clear the DTC of ECU Diagnostic detector
(Hi-DS T Scan meter)
Spec ia l dia gnostic mete rWL Remains
ONUse scan meter and K line to
connect with Scan Meter ECULocate a
Trouble Trouble-
shootingClear
DTC

2454. Trouble Identification
(1) Trouble Record (DTC storage)
When the circular diagnostic tests are involved in identification of a trouble, the SRS ECU (HAE2.5) will
store relevant codes, first/last diagnosis time and frequency of the trouble in EEPROM.
ySRS ECU (HAE2.5) can store up to 6 troubles, low voltage trouble as well as two crash records (front
and side).
yThe transmit of the DTCs are carried out in the way that the SRS ECU£¨HAE2.5£©via serial data
interface of the maintenance procedures assign the codes to the diagnostic detector.No. Trouble De scription Trouble shooting
1Ignition c irc uit 1 (drive r a irba g), high re sista nc e or ope n
circui
tYes
2Ignition circuit 1 (driver airbag), low resistance or short
circuitYes
3 Ignition circuit 1 (driver airbag), groundYes
4Ignition c irc uit 1 (drive r a irba g), connec te d to power
sourc eYes
5Ignition circuit 2 (passenger airbag), high resistance or
ope n c irc ui
tYes
6Ignition circuit 2 (passenger airbag), low resistance or
short c ircuitYes
7 Ignition circuit 2 (passenger airbag), groundYes
8Ignition circuit 2 (passenger airbag), connected to power
sourc eYes
9Ignition c irc uit 3 (drive r se a t belt pre tensione r), high
re sista nc e or ope n c irc uitYes
10Ignition c irc uit 3 (drive r se a t belt pre tensione r), low
resistance or short circui
tYes
11 Ignition c irc uit 3 (drive r se a t belt pre tensione r), groundYes
12Ignition c irc uit 3 (drive r se a t belt pre tensione r),
connec te d to power sourc eYes
13Ignition circuit 4 (passenger seat belt pretensioner), high
re sista nc e or ope n c irc uitYes
14Ignition circuit 4 (passenger seat belt pretensioner), low
resistance or short circui
tYes
15Ignition circuit 4 (passenger seat belt pretensioner),
groun
dYes
16Ignition circuit 4 (passenger seat belt pretensioner),
connec te d to power sourc eYes
17 High volta ge of powe r source Ye s
18 Low voltage of powe r sourc e Ye s
19Wa rning light trouble -c onne c te d to powe r sourc e or
short c ircuit of the light bulbYes
20 Wa rning light trouble -ground or fila me nt ope n c ircuit Ye s
21 Missing/mista ke of the algorithm parame te rs
No (replace SRS ECU (HAE2.5))
22 Previous crash recorde
dNo (replace SRS ECU (HAE2.5)) DTCs as re c ognize d by SRS ECU (HAE2.5)

246 The transmit of the DTCs are carried out in the way that the SRS ECU (HAE2.5) via serial data interface
of the maintenance procedures assign the codes to the diagnostic detector.23 C ommunication trouble Y e s
24 Inte rna l trouble (se e the follow ing ta ble )No (replace SRS ECU (HAE2.5))
25PADS （
passenger airbag deactivation
sw itch）
, connected to power source or open
circuitYes
26PADS （
passenger airbag deactivation
sw itch）
, ground or short c irc uitYes
27 PADS (passenger airbag switch), trouble Yes
28 C ra sh output pin, ground Y e s
29C ra sh output pin, short c irc uite d to pow e r
sourceYes
30PADI (passenger airbag deactivation switch
indic ator light) error, c onnected to pow er source
or light bulb short c irc uitYes
31PADI (passenger airbag deactivation switch
indic a tor light) e rror, ground or ope n c irc uitYes
32 Se a t be lt pre te nsione r se pa ra te ignition Y e s, up to 5 time s
33Se a t be lt pre te nsione r se pa ra te ignition for 6
time sNo (replace SRS ECU (HAE2.5))No. Trouble De sc ription DTC
1 Ignition c irc uit 1 (drive r a irba g), high re sistanc e or ope n circ uit B1 346
2 Ignition c irc uit 1 (drive r a irba g), low re sista nc e or short c irc uit B1 347
3 Ignition c irc uit 1 (drive r a irba g), groundB1 348
4 Ignition c irc uit 1 (drive r a irba g), c onne cte d to powe r sourc e B1 349
5 Ignition c irc uit 2 (pa sse nge r a irbag), high re sista nc e or ope n c ircuit B1 352
6 Ignition c irc uit 2 (pa sse nge r a irbag), low resista nce or short c irc uit B1 353
7 Ignition c irc uit 2 (pa sse nge r a irbag), groundB1 354
8 Ignition circuit 2 (passenger airbag), connected to power source B1 355
9 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), high re sista nc e or ope n c ircuit B1 361
10 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), low resista nce or short c irc uit B1 362
11 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), ground B1 363
12 Ignition c irc uit 3 (drive r se a t belt pre te nsione r), c onne c t to power sourc e B1 364
13Ignition c ircuit 4 (passe nger se a t be lt pre tensione r), high re sista nc e or open
circuitB1 367 Diagnostic DTCs

247(2) Internal troubles
The micro controller can check the following items not
only in the initiation check but also in the circular diagnos-
tic check.
1Trigger transistor of ignition circuit: high-end transistor
can be checked not only in the initiation check but
also in the circular diagnostic check. However, since
the low-end transistor is open when connected in short
circuit to power source, it can only be checked in the
initiation check to avoid explosion.
2The ignition voltage is provided by supercharge
converter.
3The acceleration sensor performs selfcheck in the
initiation check.
4Range of allowed deviation of acceleration sensor in the circular diagnostic check.
5Microcontroller includes AD converter, ROM, RAM, etc.
6Status of safety sensor.NOTICE
The connectors of the squib circuit contain a
shorting bar. When the connector is not
connected, the unexpected deployment is
caused by the short in the circuit arising from
the contact of the positive (+) and negative (-)
terminals or the static electricity. If there is
poor connection for connectors, the symptom
may not be removed even when the shorting
bar is connected.14Ignition c irc uit 4 (passe nger se a t be lt pre tensione r), low re sistanc e
or short c irc uitB1 368
15 Ignition c ircuit 4 (passe nger se a t be lt pre tensione r), groundB1 369
16Ignition c ircuit 4 (passe nger se a t belt pre te nsione r), c onne c t topowe r sourceB1 370
17 High volta ge of powe r sourc e B1 111
18 Low volta ge of power sourc e B1 112
19Warning light trouble -c onne c te d to powe r sourc e or light bulb short
circuitB2 500
20 Warning light trouble -ground or filame nt ope n circ uitB2 500
21 Missing/mistake of the algorithm parameters B1 661
22 Previous crash recordedB1 650
23 Communic a tion trouble B1 407
23 Inte rna l trouble (se e the following ta ble) B1 620
24PADS（
pa ssenge r airba g de a ctiva tion switch）
, c onne c ted topowe r source or open c irc uitB1 527
25PADS（
passenger airbag deactivation switch）
, ground or short
circuitB1 528
26 PADS (passenger airbag deactivation switch), trouble B1 529
27 Cra sh output pin, groundB1 676
28 Cra sh output pin, short c irc uite d to power sourc e B1 677
29PADI (passenger airbag deactivation switch indicator light) error,
c onne c ted to powe r sourc e or light bulb short c irc uitB2 505
30PADI (passenger airbag deactivation switch indicator light) error,
ground or open c irc uitB2 505
31 Se a t be lt pre tensione r se pa ra te ignitionB1 657
32 Se a t be lt pre tensione r se pa ra te ignition for 6 time s B1 658