lock GEELY FC 2008 Workshop Manual

Safety belt--Front safety belt
(d) Explode safety belt pre-tension crimper.
(1) Confirm there is no one in automobile and in 10m scope apart from automobile.
(2) Press down working switch of special tool and explode safety belt pre-tension crimper.
Hint: when LED of working switch of special tool illuminates, safety belt pre-tension crimper will
explode charged gas at the same time.
(e) Treatment for safety belt pre-tension crimper.
Hint: when scraping automobile, it is necessary to explode safety belt pre-tension crimper,
then it could be scraped with automobile.
2. Only treatment for safety belt pre-tension crimper (Treatment type for exploding front
seat safety belt).
Note:
zwhen only exploding safety belt pre-tension crimper,
forbid using the automobile belonging to customer to
explode safety belt pre-tension crimper.
zWhen exploding safety belt pre-tension crimper, it is
necessary to accord with following step.
(a) Disassemble safety belt.
Hint:cut off safety belt at its position closing to
shrinker.
(b) Confirm the function of special tool.
(c) Assemble special tool.
(1) Connect two joints of special tool to the joint of safety
belt pre-tension crimper.
Note: to avoid damaging the joint and wiring har-
ness of special tool, do not lock the twice lock
of dual-lock organization.
(2) Place the safety belt pre-tension crimper on ground, and
cover it with tyre.
Note:Place the safety belt pre-tension crimper lik-
ing that shown picturey.
(3) Place th special tool above 10mm away from tire
Note: do not damage special tool and wiring har-
ness carefully.
(d) Explode safety belt pre-tension crimper.
(1) Connect red fixed clamp of special tool to the anode of
battery (+), black fixed clamp to cathode of battery (-).
(2) Confirm there is not anyone in 10m apart from the tyre
binding safety belt pre-tension crimper.
(3) Press down working switch of special tool to explode
safety belt pre-tension crimper.
Hint: when LED of working switch of special tool
illuminates, safety belt pre-tension crimper
will explode at the same time.
Special
toolSpecial
tool
Special
toolSpecial
tool Special
toolBattery
Over 10m
 272 

Safety belt--Front safety belt
Subassembly
(e) Treatment for safety belt pre-tension crimper.
(1) Disassemble the tyre and special tool.
(2) Put safety belt pre-tension crimper in plastic bag, then
bind the bag for treatment with other parts.
N.
m : Regulated torque
Trim board of pedal of
front doorFront safety belt
locker assembly Trim cover of safety belt
lower fixed bolt Trim board of pedal
of rear door Front safety belt
crimper assembly Lower inner defending
board of middle columnTrim cover of safety belt
upper fixed bolt41
Q184C1020
41
Q184C1020
41
Q184C1020
41
Q184C1020
 273 

Safety belt--Front safety belt
Change
Hint:
zWhen assembling, please work by the sequence that is reverse with disassembling sequence,
if necessary, assembling instruction could be got.
zChanging procedure for left side and right side is same.
zRefer to subassembly drawing of front safety belt on page 273.
1. Disassemble cathode wire of battery.
2. Disassemble left front safety belt locker assembly [68010040].
(a) Disassemble driver seat assembly (referring to page 349).
(b) Disassemble safety belt locker assembly in side of driver seat gasket (referring to page 349).
(c) Only driver side: disassemble fixed clamp from gasket bracket of driver seat.
(d) Disassemble the bolts and safety belt locker assembly in side of front seat.
3. Disassemble trim board of pedal of left front door [68010020].
4. Disassemble trim board of pedal of left rear door [68010022].
 274  5. Disassemble sealed part of doorframe of left front
door [68010055].
6. Disassemble sealed part of doorframe of left rear
door [68010059].
7. Disassemble lower inner trim board of left middle
column [68010018].
8. Disassemble left front safety belt crimper assembly
[68010044].
(a) Use right-angled screwdriver to disassemble trim cover of
upper fixed bolt of safety belt.
Hint:use adhesive tape to twist its top end before using.
(b) Disassemble the bolts and crimper assembly.
(c) Use right-angled screwdriver to disassemble trim cover of
upper fixed bolt of safety belt.
Hint:use adhesive tape to twist its top end before using.
(d) Disassemble the bolts and lower fixed bolts of floor safety belt.
(e) Disconnect the joint of crimper liking that shown in figure.
Note:when disassembling the safety belt, it is necessary to turn the ignition switch to LOCK
position, and disconnect the cathode of battery for 90 seconds, then it could start to work.
(f) Disassemble the bolts and crimper.
9. Assemble left front safety belt crimper assembly.
(a) Check the inclining angle when ELR starts to lock.
(1) Confirm whether safety belt could be pulled out if the angle exceeds 45°.
Note: do not disassemble the crimper.
(b) Use the bolts to assemble crimper.
Torque: 41 N·m
(c) Use two bolts to assemble fixed seat of side shoulder belt
and safety belt.
Torque: 41 N·m
(d) Check the lock of ELR.
(e) After safety belt is assembled on automobile, check whether
the safety belt could be locked when it is pulled out quickly.
10. Assemble left front inside safety belt clamp.
Torque: 41 N·m

Rear safety belt
Subassembly
Safety belt--Rear safety belt
1. Inner trim board assembly of left rear column
[68010026]
2. Inner trim board assembly of right rear column
[68010027]
3. Backrest assembly of rear row seat [68010076]
4. Step bolt M8*20 of hexagon flange face
[68000203]
5. Cushion assembly of rear row seat [68010074]6. Rear platform with sun blind assembly
[68010032]
7. Plastic clamp of column trim board [68000089]
8. Rear safety belt crimper assembly [68010048]
9. Middle waistband of rear row safety belt with
locker assembly[68010043]
10. High mount brake light assembly [67010008]
N.
m : Regulated torque
54
982 6 10
7 1
3
8
41
41
41
41
 275 

Safety belt--Rear safety belt
.
 : Regulated torque
1
13
12
2 3
5
8
78
56
4
10
11
9
1. Inner trim board assembly of left rear column
[68010026]
2. Inner trim board assembly of right rear column
[68010027]
3. Left backrest assembly of rear row seat
[68010078]
4. Right backrest assembly of rear row seat
[68010079]
5. Combination part of Hexagon head bolt and flat
washer M6*14 [Q1400614]
6. Backrest assembly of rear row seat [68010076]7. Step bolt of hexagon flange face [68000203]
8. Combination part of hexagon bolt with flat big
washer M10*1.25*22 [Q1401022]
9. Cushion assembly of rear row seat [68010074]
10. Rear safety belt crimper assembly [68010048]
11. Middle waistband of rear row safety belt with
locker assembly [68010043]
12. Rear shelf with sun shade assembly
[68010032]
13. High mount brake light [68010008]
41
41
41
41
41
 276 

Safety belt--Rear safety belt
Change
Hint:
zWhen assembling, please work by the sequence that is reverse with disassembling sequence,
if necessary, assembling instruction could be got.
zChanging procedure for left side and right side is same.
zRefer to subassembly drawing of front safety belt on page 275.
1. Disassemble cushion assembly of rear row seat.
2. Disassemble Right backrest assembly of rear row seat [68010079]
3. Disassemble left backrest assembly of rear row seat [68010078]
4. Disassemble cushion assembly of rear row seat [68010074]
5. Disassemble backrest assembly of rear row seat [68010076]
6. Disassemble high mount brake light assembly [68010008]
7. Disassemble inner trim board assembly of right rear column [68010027]
8. Disassemble inner trim board assembly of left rear column [68010026]
9. Disassemble rear platform with sun blind assembly [68010032]
(a) Use special disassembling tool to disassemble three fixed clamps.
(b) Pull out safety belt from the clearance, then disassemble rear platform with sun blind assembly.
10. Disassemble rear safety belt crimper assembly [68010048]
(a) Disassemble the bolts and safety belt clamps.
(b) Disassemble the bolts and rear safety belt crimper assembly.
11. Disassemble middle waistband of rear row safety belt with locker assembly. [68010043]
(a) Disassemble the bolts and middle waistband of rear row safety belt with locker assembly.
 277 

12. Assemble middle waistband of rear row safety belt
with locker assembly [68010043]
(a) Use the bolts to assemble middle waistband of rear row
safety belt with locker assembly.
Torque: 41 N⋅m
Note: insure the clamp part does not press the protu-
berant part of floor.
13. Assemble rear safety belt crimper assembly.
(a) Check the inclining angle when ELR starts to lock.
(1) Confirm whether safety belt could be pulled out if the
angle exceeds 45°.
Note: do not disassemble the crimper.
(b) Use the bolts to assemble rear safety belt crimper assembly.
Torque: 41 N⋅m
(c) Use the bolts to assemble floor side clamp.
Torque: 41 N⋅m
(d) Check the lock of ELR.
(1) After safety belt is assembled on automobile, check
whether the safety belt could be locked when safety belt
is pulled out quickly.
Safety belt--Rear safety belt
Protuberant
part
Protuberant
part
 278 

Light--Light System
(a) Turn the ignition switch to OFF and open all doors, then lock driver cap side door.
(b) Unlock the drive’s side door and open any door, then inspect whether room light lights. Close the door
and inspect whether room light lights off in 15 seconds.
(c) Turn ignition switch to ON, then open any door to inspect whether room light lights off immediately.
(d) Turn ignition switch to OFF.
(e) Open or close any door to light room light. Turn ignition switch to ON before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
(f) Turn ignition switch to OFF.
(g) Open or close any door to light room light. Lock driver cap side door before room light turns off(about
15seconds) to inspect whether room light turns off immediately.
Inspect
1. Front combination headlight dimmer switch
assembly
(a) Inspect the conduction of light control switch
(1) Inspect switch on every positions, the conduction among
terminals as following table.
Switch positionsAvometer terminalsregular situations
OFF - not conduction
Position light12-6conduction
Lamp12-6conduction
Lamp7-10conduction
(b) Inspect conduction of front assembled dimmer switch
(1) Inspect switch on every parts, the conduction among terminals as following table.
Switch positionsAvometer terminalsregular situations
Flasher 11-10conduction
Low beam light9-10conduction
Distant light7-10conduction
(c) Inspect the conduction of turning light switch
(1) Inspect switch on every positions, the conduction among terminals as following table.
Switch positionsAvometer terminalsregular situations
Turn right 4-5conduction
neutral -not conduction
turn left 4-3conduction
 283 

Light--Light System
(a) Inspect the conduction of B pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth, when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
7. Inspect the C door pillar control switch assembly [67000076]
(a) Inspect the conduction of C pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth,when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
8. Trunk light switch assemble [67000073]
(a) Inspect the conduction of Trunk light switch
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
9. Front fog light relay [67000071]
(a) Inspect the conduction of front fog light relay
(1) Inspect the conduction among terminals
Standards:
Avometer terminalsregular situations
1-2 conduction
3-5 not conduction
10. Inspect rear fog light switch of instrument block
left switch units [67010003].
(a) Inspect battery’s positive wire connects to terminal 1,nega-
tive connects to terminals 7.
(b) Connect a 3.4W test bulb from battery’s positive wire to
terminal 3.
(c) Inspect lighting switch, indicator light of assembled instru-
ments and test bulb should light. If it does not accord with
regularizations, replace the switch.
11. Inspect door light assembly [67000107]
Inspect the conduction among terminals.
If the conduction does not accord with regularizations, replace
the switch.(2) Supply battery voltage(10-14V) to terminal1 and terminal2, then inspect the conduction between
terminal 3 and terminal 5.
Standard: conduction
1
 285 

Windshield/bodywork glass/wing mirror--Electric window control system
Avometer terminalsconditionsregular situations
16-earth(input +B signal)turn ignition switch from OFF to ON 0V → 10-14V
11-earthalways conduction
12-earthalways conduction
15-earth(input IG signal)turn ignition switch from OFF to ON 0V→10-14V
(4) Inspect other windows whether they can not actuate except window of driver seat room, when the
electric window switch locked.
2. Inspect automation function
(a) inspect basic function
(1) Turn the ignition switch to ON
(2) Inspect whether driver seat window automatic descends completely, when you press electric win-
dow main switch.
(3) Inspect whether driver seat window stop descending when driver seat window automatic descends
and press the main switch.
If the voltage and conduction do not accord with the regulations, the input side of electric window main
switch may have malfunction.
(b) Inspect the joint terminal voltage when connect the joint.
If the voltage does not accord with the regulations, electric window main switch may have malfunction.
(c) Inspect whether AUTO headlamp(LED) lights when connect the joint, turn the ignition switch from
OFF to ON.
 318 
Avometer terminalsconditionsregular situations
4-earth turn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.UP) Main switch from OFF to UP (manual operation)
9-earthturn the ignition switch to ON, turn Driver
seat0V→over 9V
(output P/W.DOWN)Main switch from OFF to DOWN (manual operation)
9-earthturn the ignition switch to ON, turn Off Driver
seat
window → driver seat Main switch to DOWN 0V→over9V→0V
(output P/W.DOWN)
(auto Operation)
→ windows open completely.
3. Inspect electric window main switch assembly
(a) Inspect operations
(1) Disassemble the joint of driver seat electric window main
switch and inspect the voltage and conduction among
terminals.