lock GEELY FC 2008 Repair Manual

Brake--Front brake assemblyFront brake assemblyOverhaul1. Disassemble front wheels.
2. Discharge brake liquid.Note: do not spill the brake liquid on paint surface of automobile body, if having, wash it cleanly.3. Disassemble brake branch pump assembly.(a) Disassemble the bolts and gaskets of brake hose joint on
brake branch pump, then disassemble brake hose.
Hint: the gasket has two types: two sheets type or one
type.
(b) Fix sliding pin of cylinder body to disassemble two bolts.4. Disassemble brake block of front wheels.(a) Disassemble brake block with muffle gasket.
(b) Disassemble muffle gasket from every brake block.5. Disassemble support sheet of brake block.
6. Disassemble sliding pin of brake branch pump.Disassemble sliding pin on branch pump bracket.7. Disassemble dustproof cover on brake branch pump.Disassemble two dustproof covers from brake branch pump
of disk.8. Disassemble left front brake branch pump.Disassemble two bolts and brake branch pump bracket.9. Disassemble dustproof cover of branch pump.Use screw driver to disassemble oil seal loop and dustproof
cover.10. Disassemble the piston of brake branch pump.(a) Put a cloth or similar thing between piston and branch pump.
(b) Use compressed air to disassemble piston from branch
pump.
Warning: when using compressed air, do not put your
finger at the front of piston.
Note: you could not be splashed by brake liquid.11. Disassemble oil seal of piston.Use screw driver to disassemble oil seal of piston from branch
pump.12. Disassemble exhaust bolt of branch pump.Brake branch pump
Dustproof cover141

Brake--Front brake assembly13. Check the brake branch pump and pistonCheck whether there is rust or scratch in cylinder of branch
pump and piston.14. Check the thickness of brake blockUse rule to measure the thickness of brake block.
Standard thickness: 11.00mm
Minimal thickness: 1.0mm15. Check support sheet of brake block
142Confirm the support sheet could rebound enough without any distortion, crack or abrasion, and it has
removed rust, dust and sundries completely.16. Check the thickness of brake diskUse centimeter to measure the thickness of brake disk.
Standard thickness: 25.00mm
Minimal thickness: 23.0mm17. Disassemble front brake disk(a) Make a mark on corresponding position of brake disk and shaft hub.
(b) Disassemble brake disk.18. Assemble brake diskHint: choose the position with minimal terminal run-out quantity to assemble brake disk.19. Check the terminal run-out of brake disk(a) Lock the brake disk temporarily with shaft hub nut.
Torque: 103
± ± ± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m
(b) Use centimeter to measure the terminal run-out of brake
disk on the position with 10mm apart from the exterior edge
of brake disk.
Maximal run-out quantity: 0.05mm
(c) If terminal run-out of brake disk exceeds or equals to maxi-
mal value, firstly, check the axial clearance of bearing, then
check the terminal run-out of shaft hub, if they are both
normal, adjust the terminal run-out of brake disk to eligible
value or use turning motor to turn terminal surface of brake
disk.20. Lock exhaust bolt temporarilyLock exhaust bolt temporarily on front brake branch pump.21. Assemble oil seal of piston(a) Spread lithium soap base glycol lubricating grease on new oil seal of piston.
(b) Assemble oil seal of piston on brake branch pump.
Note: do not force piston to assemble in branch pump compulsively.22. Assemble piston of front brake branch pump(a) Spread lithium soap base glycol lubricating grease on the piston.
(b) Assemble piston on brake branch pump.
Note: do not force piston to assemble in branch pump compulsively.

Brake--Front brake assembly23.Assemble dustproof cover of branch pump..(a) After spreading lithium soap base glycol lubricating grease
on new dustproof cover of branch pump, assembling it in
brake branch pump.
Hint: dustproof cover should be assembled in branch
pump firmly.
(b) Use wrench to assemble fixing loop.
Note: do not damage dustproof cover.24. Assemble brake branch pump bracket.Use two bolts to assemble brake branch pump bracket.
Torque: 106
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m25. Assemble dustproof cover of brake branch pump
bracket.(a) Spread lithium soap base glycol lubricating grease on new
dustproof cover.
(b) Assemble two dustproof covers in front brake branch pump
bracket.26. Assemble sliding pin of front brake branch pump.(a) Spread lithium soap base glycol lubricating grease on the
surface of sliding part and sliding pin.
(b) Assemble two sliding pins in front brake branch pump
bracket.27. Assemble support sheet of brake block.143 28. Assemble brake block.Note: when changing brake block, muffle gasket should be changed with brake block at the same
time.
(a) Spread brake lubricating grease on both sides of every muffle gasket.
(b) Assemble muffle gasket on every brake block.
(c) When assembling inner brake block, abrasion indicator should face the upside.
Note: do not attach oil dirt or lubricating grease on the surface of brake block and brake disk.29. Assemble brake branch pump assembly.(a) Use two bolts to assemble brake branch pump.
Torque: 34
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
(b) Use joint bolt to assemble new gasket and brake hose.
Torque: 30
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
Hint: Gasket has two types: two sheets type and one type.
Bracket soft pipe should be assembled in localizing hole of branch pump firmly.30. Add brake liquid in storage tank.
31. Discharge the air in brake main pump.
32. Discharge the air in brake pipeline.
33. Check the liquid level of storage tank.
34. Check whether the brake liquid leaks.
35. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m

Brake--Rear brake assemblyRear brake assembly
OverhaulHint: overhaul procedure for right side is same as the left side.1. Disassemble rear wheels.
2. Discharge brake liquid.Note: do not spill the brake liquid on paint surface of automobile body, if having, wash it cleanly.3. Disassemble brake block of rear wheels.(a) Disassemble fixing clamp of anti-vibration spring.
(b) Disassemble two guide pins of brake block and brake block
with muffle gasket.
(c) Take down muffle gasket from every brake block.4. Disassemble left rear brake branch pump.(a) Disassemble the joint, bolt and gasket of brake hose of brake
branch pump, then disassemble brake hose.
Hint: gasket has two types: two sheets type and one
sheet type
(b) Disassemble two bolts and brake branch pump.5. Disassemble the bushing of brake branch pump.Disassemble two bushings from brake branch pump.6. Disassemble dustproof bushing of rear brake.Disassemble three dustproof bushings.7. Disassemble dustproof cover of branch pump.Use screw driver to disassemble fixing loop and dustproof cover.8. Disassemble the piston of brake branch pump.(a) Put a cloth or similar thing between the piston and branch
pump.
(b) Use compressed air to disassemble piston from branch
pump.
Warning: when using compressed air, do not put your
fingers at the front of piston.
Note: do not let brake liquid splash on you.9. Disassemble oil seal of piston.144

Brake--Rear brake assemblyUse screw driver to disassemble oil seal of piston from brake
branch pump.
Note: do not damage cylinder wall and slot.10. Disassemble exhaust bolt of branch pump.
11. Check whether there is any dust or scratch on
branch pump and piston.
12. Check the thickness of brake block.Use rule to measure the thickness of brake block.
Standard thickness: 10.0mm
Minimal thickness: 1.0mm13. Check the thickness of brake disk.Use centimeter of exterior diameter to measure the thickness
of disk.
Standard thickness: 9.0mm
Minimal thickness: 8.0mm14. Disassemble rear brake disk.(a) Make a mark on disk and shaft hub.
(b) Disassemble disk.15. Assemble brake disk.Hint: choose the position with minimal terminal run-out
to assemble brake disk.16. Check the terminal run-out of disk.(a) Lock the disk temporarily with screw cap of shaft hub.
Torque: 103-10 N
⋅ ⋅⋅ ⋅
⋅m
(b) Use centimeter to measure the terminal run-out of brake
disk on the position with 10mm apart from the exterior edge
of brake disk.
Maximal run-out quantity: 0.15mm
(c) If terminal run-out of brake disk exceeds or equals to maxi-
mal value, firstly, check the axial clearance of bearing, then
check the terminal run-out of shaft hub, if they are both
normal, adjust the terminal run-out of brake disk to eligible
value or use turning motor to turn terminal surface of brake
disk.17. Lock exhaust bolt of rear brake branch pump
temporarily.Lock exhaust bolt to rear brake branch pump temporarily.18. Assemble oil seal of piston.(a) Spread lithium soap base glycol lubricating grease on new
oil seal of piston.
(b) Assemble oil seal of piston to brake branch pump.145

Brake--Rear brake assembly24. Assemble rear brake block.Note: when changing brake block, the inside of muffle gasket should be changed together.
(a) When assembling muffle gasket on every brake block, it is necessary to spread brake lubricating
grease on the inside of muffle gasket.
(b) When assembling inner brake block, abrasion indicator should face upside.
Note: do not attach any oil dirt or lubricating grease on the surface of brake block and brake
disk.
(c) Assemble two guide pins of brake block.
(d) Assemble fixing clamp of anti-abrasion spring.25. Add brake liquid in storage tank.
26. Discharge the air in brake main pump (referring to page 135).
27. Discharge the air in brake pipeline (referring to page 135).
28. Check the liquid level in storage tank.
29. Check whether brake liquid leaks.
30. Assemble rear wheels.Torque: 103
± ±± ±
± 10N
⋅ ⋅⋅ ⋅
⋅m147

Brake--Hydraulic pressure control unit3. Disassemble gasket of right wheel wing.
4. Disassemble hydraulic control unit and bracket.(a) Disassemble the joint and bolt.
(b) Turn the locking bolt of joint of hydraulic control unit, and
disassemble the joint.
(c) Use special tool to disassemble the brake oil pipe on hy-
draulic control unit.
(d) Use label to mark the name of every oil pipe, and tie it on
oil pipe.
(e) Disassemble screw caps, two bolts and hydraulic control
unit and bracket.5. Disassemble hydraulic control unit assembly.Disassemble three bolts and hydraulic control unit from the bracket.6. Assemble hydraulic control unit assembly.Assemble three bolts and hydraulic control unit on the bracket with three bolts.
Torque: 4.7 N
⋅ ⋅⋅ ⋅
⋅m149Connect the front
of main cylinder
Connect the back
of main cylinder
Connect 2#
brake pipe
Connect the front left
Connect 2#
brake pipeConnect the front right

Parking brakeParking brake systemMalfunction phenomenon tableUse following table to find the reason of malfunction, the number in table indicates the preferred se-
quence of possible reason. Please check each part by sequence, if necessary, change this part.Parking brake--Parking brake systemAdjustment1. Disassemble rear wheels
2. Adjust the clearance of parking brake shoe
3. Assemble rear wheelsTorque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m4. Check the travel of parking brake handle.Pull up the parking brake handle and calculate the sound num-
ber of handle.
When parking brake handle locates 196N: 6-9 sounds.5. Adjust the travel of parking brake handle(a) Disassemble upper trim board of central box.
(b) Disassemble central box.
(c) Release locking screw cap, then rotate adjusting screw cap
until handle travel accords with the specification.
(d) Tighten locking screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
(e) Assemble central box.
(f) Assemble trim board on central box.Malfunction phenomenon Possible malfunction part Reference page
1. Travel of parking brake handle (adjusted badly). 154
2. Pull cable of parking brake (attached).156, 158
Brake lag 3. Clearance of parking brake shoe (adjusted badly). 161
4. Friction plate of parking brake shoe (damaged or distorted). 161
5. Tension or return spring (damaged). 161Lock the screw cap
Adjust the
screw cap154

Parking brake handle assemblyChange1. Disassemble trim board on central box.
2. Disassemble parking brake hole cover.
3. Disassemble central box.
4. Disassemble parking brake handle assembly.(a) Disassemble locking screw cap and adjusting screw cap.
(b) Disassemble the joint of parking brake switch.
(c) Disassemble two bolts and parking brake handle.5. Disassemble parking brake switch assembly.Disassemble the screw and parking brake switch.6. Assemble parking brake switch assembly.Assemble parking brake switch assembly with screw.7. Assemble parking brake pull cable.(a) Connect parking brake pull cable to handle and assemble adjusting screw cap and locking screw cap.
(b) Assemble parking brake handle with two bolts.
Torque: 13 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect the joint of parking brake switch.8. Check the travel of parking brake handle (referring to page 154).
9. Adjust the travel of parking brake handle (referring to page 154).Parking brake--Parking brake handle assembly155

18. Check the assembly of parking brake system.
Check every part after assembly.
Note: do not attach oil dirt or lubricating grease on contacting surface between shoe friction
sheet and brake drum.
Parking brake--Parking brake assembly
19. Assemble the brake
20. Adjust the clearance of parking brake shoe.
(a) Lock screw cap of shaft hub temporarily.
(b) Disassemble hole plug, then use screw driver to turn the
adjustor until brake drum is locked by shoe.
(c) Return the adjustor for 8 gears.
(d) Check whether shoe has lag.
(e) Assemble hole plug.
21. Assemble rear disk type brake branch pump assem-
bly (LH).
22. Assemble rear wheels.
Torque: 103
± ±± ±
± 10N
⋅ ⋅⋅ ⋅
⋅m
23. Check the travel of parking brake drag lever.
24. Adjust the travel of parking brake drag lever.
Left
Right
Front
Front
Increase the
clearance
Decrease the
clearance
 164