GEELY FC 2008 Workshop Manual

Anti-stealing and door lock--Electric door lock control system
2. Check front passenger seat door locker assembly
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
3. Check the left rear and right rear door locker assembly.
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
OpenClose
Open
Close
 360 
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose

Anti-stealing and door lock--Electronic anti-stealing system
Electronic anti-stealing system
Electronic anti-stealing system consists of anti-stealing controller, anti-stealing loop and transmitter. One
end of loop covers ignition locker core, the other end connects with anti-stealing controller, and the other end
of controller connects with engine ECU, at the same time, transmitter is assembled in key. Memory of
transmitter stores only mark (code) showing the legal identity of automobile owner, transmitter, anti-stealing
controller and electric injection ECU constitutes a multi-layer effective electronic anti-stealing system verified
by password.
If customer key loses, anti-stealing ECU is changed or engine ECU is changed, it is necessary to match
again in repairing station. When automobile leaves the factory, safety password is delivered directly to
owner for keeping with the type of secrecy. If it is necessary to make a new key, change anti-stealing
controller and make other operations, owner should bring the safety password with the automobile to repair
in repairing station. Repairing station should keep repairing (make new key, change anti-stealing controller
and so on) record for inquiring in future.
 361 

Electric sunroof (optional)--Sunroof
Bolt
Screw cap
Electric sunroof (optional)
Sunroof
Overhaul
Hint: when assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special specification.
1. Disassemble inner trim board of top (referring to page 390).
2. Disassemble the glass of sunroof.
(a) Use planetary wrench to disassemble planetary screw.
(b) Pull the glass upwards to disassemble it.
3. Disassemble waterproof adhesive tape of sunroof.
4. Disconnect connection of wiring harness.
5. Disassemble shell body of sunroof.
(a) Disassemble four drain hoses.
(b) Liking that shown in figure, disassemble four bolts and six screw caps, then disassemble shell body.
6. Disassemble trim sun shade of sunroof.
(a) Disassemble the screw and stopper.
(b) Disassemble trim sun shade of sunroof.
 362 

Electric sunroof (optional)--Sunroof
7. Use screw driver (twisted by adhesive tape) to align
the sunroof driving pull cable with right mark.
8. Assemble sunroof shell body assembly.
(a) Bolt.
Torque: 5.5 N
⋅ ⋅⋅ ⋅
⋅m
(b) Screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
9. Assemble the glass of sunroof.
(a) Check the phase difference between sunroof waterproof ad-
hesive tape and top gasket.
Front end and rear end: 0±1.5mm
Rear corner: 0±1.5mm
0-1.5mm
(b) Adjustment
Use T25 planetary wrench to loosen the screw to adjust
the sunroof on correct position, then lock the screw.
10. Inspection for water leakage.
(a) After the adjustment, check whether the sunroof leaks water.
(b) If sunroof leaks water, adjust it again.
Assembly mark
 363 

Electric sunroof (optional)--Sunroof system
Inspection for sunroof function
1. Inspection for sliding opening function.
(1) Turns ignition switch to ON, when spot contacting sunroof
switch keystroke 2, the sunroof will start automatic sliding
opening work, and it does not stop until it is at complete
opening state. If spot contacting it in running process, or
pressing keystroke 1 or 2 for long time, sunroof glass will
stop running immediately.
(2) Turns ignition switch to ON, when pressing keystroke 2 for
Sunroof system
Specification for sunroof function
1. Operation category
Spot contact: press the keystroke one time, then release immediately (the time is less than 0.3 seconds).
Long press: press the key stroke for long time (the time is more than 0.3).
2. Specification for function.
Anti-clamping function: spot contact the keystroke to make the sunroof could face 10 Kg resistance in the
process of closing from any position, at this time, electric motor turns oppositely, and the sunroof returns
turn-up or opening state.
Automatic closing function: when the key is pulled out from ignition locker, at this time, the sunroof is not
at closing state, it will close automatically in three seconds.
long time, the sunroof will start automatic sliding opening work, and it does not stop until it is at
complete opening state. If releasing keystroke 2 in running process, the sunroof glass will stop running
immediately.
2. Inspection for sliding closing function.
(1) Turns ignition switch to ON, if the sunroof is at opening state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically slide to closing state. If spot contacting it or pressing
keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at opening state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 1 in running
process, sunroof glass will stop running immediately.
3. Inspection for turn-up opening function
(1) Turns ignition switch to ON, if the sunroof is at closing state, when spot contacting sunroof switch
keystroke 1, the sunroof will automatically move to turn-up opening state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at closing state, when pressing sunroof switch keystroke
1 for long time, the sunroof will automatically slide to turn-up opening state. If releasing keystroke 1 in
running process, sunroof glass will stop running immediately.
4. Inspection for turn-up closing function
(1) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when spot contacting sunroof
switch keystroke 2, the sunroof will automatically move to closing state. If spot contacting it again or
pressing keystroke 1 or 2 for long time in running process, sunroof glass will stop running immediately.
(2) Turns ignition switch to ON, if the sunroof is at turn-up opening state, when pressing sunroof switch
keystroke 2 for long time, the sunroof will automatically slide to closing state. If releasing keystroke 2
in running process, sunroof glass will stop running immediately.
 364 
Front
Rear

Electric sunroof (optional)--Sunroof system
Inspection for sunroof switch
(a) Check the function of switch. Disassemble front top light,
and disassemble the joint of front top light, then check the
joint at the side of switch liking that shown in figure.
Malfunction phenomenon table Position of parts
Malfunction phenomenon
Sunroof system does not work
Sunroof system works abnormallyPossible malfunction part
1. Ignition switch.
2. Control switch of sunroof.
3. 25A, 15# fuse.
4. Wiring harness
1. Control switch of sunroof.
2. Wiring harnessReference page
-
-
-
-
-
-
 365 
Terminal connected by avometer
2-4
2-5ConditionSpot contact or press
keystroke 2 for long time
Spot contact or press
keystroke 1 for long time
Regulated situa-
tion
Conduction
Conductiion
Shell body of sunroof
Motor of sunroof
Switch of sunroof

Engine cover/automobile door
Engine cover
Adjustment
Engine cover/automobile door--Engine cover
 366  1. Check engine cover assembly.
Check whether the clearance of engine cover is in regulated
value shown in table.
2. Adjust engine cover assembly.
(a) Adjust engine cover assembly by loosening the hinge bolt at
the side of engine cover.
Torque: 13 N
⋅ ⋅⋅ ⋅
⋅m
(b) Adjust engine cover assembly by turning the gasket.
(c) Adjust engine cover assembly by loosening three bolts of
engine cover locker.
Torque: 7.0 N
⋅ ⋅⋅ ⋅
⋅m

Engine cover/automobile door--Front automobile door
Front automobile door
Subassembly
.
 : Regulated torque
1
2
3
4
5
6
78
9
10
1118
17 16 15 14
2220
19
21 13
12 32
26
2731 30
29 28 272625
33
24
23
 367 

Engine cover/automobile door--Front automobile door 368 Name of parts Specification Amount Marked
number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33Number of parts
68000147
68000162
68000149
Q1860610
68000159
67000157
Q32006
68000153
Q2580816
Q1860610
JQ2756316
67000123
Q1860610
68000145
Q2716319
67000132
68000144
Q2714216
68010050
Q2204816
67000107
68000141
68000160
62000479
62000025
62000024
Q1840820
68000163JQ1840816T1F31Q1400616
62000027
68010052
68000151Right front glass assembly
Seal tape of right front glass leading slot
Right front glass leading slot assembly
Hexagon flange face bolt
Exterior seal tape of right front door glass
Right exterior electric rearview mirror assembly
Hexagon flange face nut
Right front door locker organization assembly
Inner hexagon floriated raised countersunk head screw
Hexagon flange face bolt
Combination part of hexagon head self-tapping screw with flat gasket
Right front door glass lift assembly
Hexagon flange face bolt
Right front door board bracket
Cross slot plate head self-tapping screw
Right front small speaker cover assembly
Right front door control panel assembly
Freerson plate head self-tapping screw
Right front door inner defending board assemblyCombination part of cross slot plate head self-tapping screw with flat washerDoor light assembly
Right front door defender water curtain assembly
Right front door seal tape assembly
Right front door assembling assembly
Right front door upper hinge assembly
Hexagon flange face bolt (with step)
Hexagon flange face bolt
Front door limiter assembly
Hexagon flange face bolt
Combination part of hexagon head bolt with flat washer
Right front door lower hinge assembly
Right side door inner handle assembly
Right front door exterior handle assembly1
1
1
1
1
1
3
1
3
2
1
1
6
1
2
1
1
1
1
1
1
1
1
1
1
2
4
2
2
2
1
2
1M6 × 10
M6
M6× 18
M6× 10
ST6.3 × 16
M6 × 10
ST6.3 × 19
ST4.2 × 16
ST4.8 × 16
M8× 20
M8× 20
M8× 16
M8× 16

Engine cover/automobile door--Front automobile door
Overhaul
Hint:
zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; but when it has items that need to pay special attention, it will add special
specification.
zOverhaul procedure for right side is same as the left side.
zPlease refer to subassembly figure of front door on page 360.
1. Disassemble left front door control panel assembly [68000142]
(a) Disassemble the screw.
(b) Use screw driver to disassemble left front door control panel assembly.
Hint: before using screw driver, it is necessary to wrap its needled top with adhesive tape.
(c) Disassemble the joint.
2. Disassemble left front door inner defending board assembly [68010049]
(a) Disassemble the screw.
(b) Without equipping with door control light: use screw driver to disassemble door inner defending board
assembly.
(c) Equipping with door control light: use screw driver to disassemble door inner defending board assembly,
then disassemble the joint again.
(d) Equipping with door control light: use screw driver to disassemble door control light.
3. Disassemble left door inner handle assembly [68010051]
(a) Disassemble inner handle, and disassemble two pull cables from inner handle.
4. Disassemble repairing hole cover of left front door
5. Disassemble left front small loudhail cover assembly [67000131]
 369  6. Disassemble left exterior electric rearview mirror
assembly [67000155]
(a) Disassemble the joint.
(b) Disassemble three screw caps and left exterior electric
rearview mirror.
7. Disassemble exterior seal tape of left front door glass
[68000158]