display GENESIS G80 2023 Manual PDF

Page 430 of 661

7-38
Driver Assistance System
ORG3EV071025L
Collision-avoidance assist (while driving)
[To warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message
will appear on the cluster. At the
same time, an audible warning will
sound, warning light on the head-up
display (if equipped) will blink and the
steering wheel will vibrate.
[Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is between 40~120 mph (60~200
km/h) and both lane markings of the
driving lane are detected.
[Emergency braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.
WARNING
[&ROOLVLRQ$YRLGDQFH$VVLVWZLOO
EHFDQFHOHGXQGHUWKHIROORZLQJ
circumstances:
-<RXUYHKLFOHHQWHUVWKHQH[WODQH
E\DFHUWDLQGLVWDQFH
-<RXUYHKLFOHLVDZD\IURPWKH
collision risk
-7KHVWHHULQJZKHHOLVVKDUSO\
steered
-7KHEUDNHSHGDOLVGHSUHVVHG
-)RUZDUG&ROOLVLRQ$YRLGDQFH$VVLVW
is operating
[$IWHU%OLQG6SRW&ROOLVLRQ$YRLGDQFH
$VVLVWRSHUDWLRQRUODQHFKDQJH
\RXPXVWGULYHWRWKHFHQWHURIWKH
ODQH%OLQG6SRW&ROOLVLRQ$YRLGDQFH
$VVLVWZLOOQRWRSHUDWHLIWKHYHKLFOHLV
QRWGULYHQLQWKHFHQWHURIWKHODQH

Page 431 of 661

7-39
07
ORG3EV071026L
Collision-avoidance assist (while
departing)
[To warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message
will appear on the cluster. At the
same time, an audible warning will
sound, warning light on the head-up
display (if equipped) will blink and the
steering wheel will vibrate.
[Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is below 2 mph (3 km/h) and the
speed of the vehicle in the blind spot
area is above 3 mph (5 km/h).
[Emergency braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.
ORG3EV071004L
[When the vehicle is stopped due
to emergency braking, the ‘Drive
carefully’ warning message will
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.

Page 452 of 661

7-60
Driver Assistance System
OJK071214N
3. The set speed limit will be displayed
on the cluster.
If you would like to drive over the
preset speed limit, depress the
accelerator pedal beyond the pressure
point to activate the kickdown
mechanism.
The set speed limit will blink and
chime will sound until you return the
vehicle speed within the speed limit.
Information
[When the accelerator pedal is not
depressed beyond the pressure point,
vehicle speed will maintain within the
speed limit.
[A clicking sound may be heard from
the kickdown mechanism when the
accelerator pedal is depressed beyond
the pressure point.
Temporarily pausing Manual Speed
Limit Assist
ORG3EV071111L
Press the switch to temporarily
pause the set speed limit. The set speed
limit will turn off but the Speed Limit
(
) indicator will stay on.

Page 456 of 661

7-64
Driver Assistance System
Intelligent Speed Limit Assist
Operation
Warning and control
Intelligent Speed Limit Assist will warn
and control vehicle speed by ‘Displaying
speed limit’, ‘Warning overspeed’ and
‘Changing set speed’.
Information
Intelligent Speed Limit Assist warning
and control are described based on the
Offset adjusted to &#39;0&#39;. For details on Offset
setting, refer to the “Intelligent Speed
Limit Assist Settings”.ORG3EV071030N
Displaying speed limit
Speed limit information is displayed on
the instrument cluster.
Information
[If speed limit information of the road
cannot be recognized, &#39;---&#39; sign will be
displayed. Please refer to &#34;Limitations
of Intelligent Speed Limit Assist&#34; if the
road signs are difficult to recognize.
[Intelligent Speed Limit Assist provides
additional road sign information in
addition to speed limit. The additional
road sign information provided may
vary according to your country.
[Supplementary sign displayed under
the speed limit or overtaking restriction
sign means the conditions under which
the signs must be followed. If the
supplementary sign is not recognized, it
will be displayed as blank.
[The images and colors in the cluster
may differ depending on the cluster
type or theme selected from the cluster.

Page 457 of 661

7-65
07
ORG3EV071031N
Warning overspeed
When driving at a speed higher than the
displayed speed limit, the red speed limit
indicator will blink.
OJK071183NOJK071190N
Changing set speed
If the speed limit of the road changes
during the operation of Manual Speed
Limit Assist or Smart Cruise Control, an
arrow in the direction of up or down is
displayed to inform the driver that the set
speed needs to be changed. At this time,
the driver can change the set speed
according to the speed limit by using the
+ or – switch on the steering wheel.
WARNING
[,IWKH2IIVHWLVDGMXVWHGRYHUSTWKH
set speed will change to a higher
speed than the speed limit of the
URDG,I\RXZDQWWRGULYHEHORZWKH
VSHHGOLPLWDGMXVWWKH2IIVHWXQGHU
'0' or use the – switch on the steering
ZKHHOWRORZHUWKHVHWVSHHG
[(YHQDIWHUFKDQJLQJWKHVHWVSHHG
according to the speed limit of the
URDGWKHYHKLFOHFDQVWLOOEHGULYHQ
RYHUWKHVSHHGOLPLW,IQHFHVVDU\
GHSUHVVWKHEUDNHSHGDOWRUHGXFH
\RXUGULYLQJVSHHG
[If the speed limit of the road is under
PSK NPK WKHVHWVSHHG
FKDQJHIXQFWLRQZLOOQRWZRUN
[Intelligent Speed Limit Assist
operates using the speed unit in the
LQVWUXPHQWFOXVWHUVHWE\WKHGULYHU
If the speed unit is set to a unit other
WKDQWKHVSHHGXQLWXVHGLQ\RXU
FRXQWU\,QWHOOLJHQW6SHHG/LPLW
$VVLVWPD\QRWRSHUDWHSURSHUO\
Information
[For more details on Manual Speed
Limit Assist operation, refer to
“Manual Speed Limit Assist (MSLA)”
section in this chapter.
[For more details on Smart Cruise
Control operation, refer to “Smart
Cruise Control (SCC)” section in this
chapter.

Page 462 of 661

7-70
Driver Assistance System
[The driver’s attention level is displayed
on the scale of 1 to 5. The lower the
level is, the more inattentive the driver
is.
[The level decreases when the driver
does not take a break for a certain
period of time.
7DNLQJDEUHDN
OTM070105L
[The ‘Consider taking a break’ message
will appear on the cluster and an
audible warning will sound to suggest
that the driver take a break, when the
driver’s attention level is below 1.
[Driver Attention Warning will not
suggest a break when the total driving
time is shorter than 10 minutes or 10
minutes has not passed after the last
break was suggested.
WARNING
)RU\RXUVDIHW\RQO\FKDQJHWKH
6HWWLQJVDIWHUSDUNLQJWKHYHKLFOHDWD
VDIHORFDWLRQ
&$87,21
['ULYHU$WWHQWLRQ:DUQLQJPD\
VXJJHVWDEUHDNGHSHQGLQJRQWKH
GULYHUTVGULYLQJSDWWHUQRUKDELWV
HYHQLIWKHGULYHUGRHVQTWIHHOIDWLJXH
['ULYHU$WWHQWLRQ:DUQLQJLVD
VXSSOHPHQWDOIXQFWLRQDQGPD\QRW
EHDEOHWRGHWHUPLQHZKHWKHUWKH
GULYHULVLQDWWHQWLYH
[7KHGULYHUZKRIHHOVIDWLJXHGVKRXOG
WDNHDEUHDNDWDVDIHORFDWLRQHYHQ
WKRXJKWKHUHLVQREUHDNVXJJHVWLRQ
E\'ULYHU$WWHQWLRQ:DUQLQJ
Information
[For more details about setting
instrument panel, refer to “LCD
Display Control” section in chapter 4.
[Driver Attention Warning will reset the
last break time to 00:00 in the following
situations:
-The vehicle is turned off
-The driver unfastens the seat belt
and opens the driver’s door
-The vehicle is stopped for more than
10 minutes
[When the driver resets Driver Attention
Warning, the last break time is set to
00:00 and the driver’s attention level is
set to High.

Page 463 of 661

7-71
07
Leading Vehicle Departure Alert
function
OJK070142L
When a detected vehicle in front departs
from a stop, Leading Vehicle Departure
Alert will inform the driver by displaying
the ‘Leading vehicle is driving away’
message on the cluster and an audible
warning will sound.
WARNING
[,IDQ\RWKHUV\VWHPTVZDUQLQJ
PHVVDJHLVGLVSOD\HGRUDXGLEOH
ZDUQLQJLVJHQHUDWHG/HDGLQJ
9HKLFOH'HSDUWXUH$OHUW
VZDUQLQJ
PHVVDJHPD\QRWEHGLVSOD\HG
DQGDXGLEOHZDUQLQJPD\QRWEH
JHQHUDWHG
[7KHGULYHUKDVWKHUHVSRQVLELOLW\WR
VDIHO\GULYHDQGFRQWUROWKHYHKLFOH
&$87,21
[/HDGLQJ9HKLFOH'HSDUWXUH$OHUWLVD
VXSSOHPHQWDOIXQFWLRQDQGPD\QRW
DOHUWWKHGULYHUZKHQHYHUWKHIURQW
YHKLFOHGHSDUWVIURPDVWRS
[$OZD\VFKHFNWKHIURQWRIWKH
YHKLFOHDQGURDGFRQGLWLRQVEHIRUH
GHSDUWXUH
'ULYHU$WWHQWLRQ:DUQLQJ
Malfunction and Limitations
Driver Attention Warning
malfunction
OTM070107L
When Driver Attention Warning is not
working properly, the ‘Check Driver
Attention Warning (DAW) system’
warning message will appear on the
cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. If this occurs, have the
vehicle inspected by an authorized
retailer of Genesis Branded products.
Limitations of Driver Attention
Warning
Driver Attention Warning may not work
properly in the following situations:
[The vehicle is driven violently
[The vehicle intentionally crosses over
lanes frequently
[The vehicle is controlled by Driver
Assistance system, such as Lane
Keeping Assist

Page 471 of 661

7-79
07
„Left side„Right side
ORG3EV071119ORG3EV071120
Blind-Spot View Monitor displays the
rear blind spot area of the vehicle in the
cluster when the turn signal is turned on
to help safely change lanes.
Detecting sensor
ORG3EV071036[1], [2]: Surround-side view camera
(camera located at bottom of the mirror)
Refer to the picture above for the
detailed location of the detecting
sensors.
%OLQG6SRW9LHZ0RQLWRU
Settings
Setting features
Blind-Spot View
With the vehicle on, select ‘Driver
$VVLVWDQFH

Page 472 of 661

7-80
Driver Assistance System
Blind-Spot View Monitor
Operating conditions
When the left or right side turn signal
turns on, the image in that direction is
displayed on the instrument cluster.
Off conditions
[When the turn signal turns off, the
image on the instrument cluster will
turn off.
[When the hazard warning flasher
is on, Blind-Spot View Monitor will
turn off, regardless of the turn signal
status.
[When other important warning is
displayed on the instrument cluster,
Blind-Spot View Monitor may turn off.
%OLQG6SRW9LHZ0RQLWRU
Malfunction
When Blind-Spot View Monitor is not
working properly, or the cluster display
flickers, or the camera image does
not display properly, have the vehicle
inspected by an authorized retailer of
Genesis Brand products.
WARNING
[7KHLPDJHVKRZQRQWKHFOXVWHUPD\
differ from the actual distance of the
REMHFW0DNHVXUHWRGLUHFWO\FKHFN
WKHYHKLFOH
VVXUURXQGLQJVIRUVDIHW\
[$OZD\VNHHSWKHFDPHUDOHQVFOHDQ
,IWKHOHQVLVFRYHUHGZLWKIRUHLJQ
PDWHULDOLWPD\DGYHUVHO\DIIHFW
camera performance and Blind-
6SRW9LHZ0RQLWRUPD\QRWRSHUDWH
SURSHUO\

Page 479 of 661

7-87
07
Overtaking Acceleration Assist
Overtaking Acceleration Assist operates
when the turn signal indicator is turned
on to the left while Smart Cruise Control
is operating, and the following conditions
are satisfied:
[Your vehicle speed is above 40 mph
(60 km/h)
[The hazard warning flasher is off
[A vehicle is detected in front of your
vehicle
[Deceleration is not needed to
maintain distance with the vehicle in
front
WARNING
[When the turn signal indicator is
turned on to the left while there is
DYHKLFOHDKHDGWKHYHKLFOHPD\
DFFHOHUDWHWHPSRUDULO\3D\DWWHQWLRQ
WRWKHURDGFRQGLWLRQVDWDOOWLPHV
[5HJDUGOHVVRI\RXUFRXQWULHVGULYLQJ
GLUHFWLRQ2YHUWDNLQJ$FFHOHUDWLRQ
Assist will operate when the
FRQGLWLRQVDUHVDWLVILHG:KHQ
using the function in countries with
GLIIHUHQWGULYLQJGLUHFWLRQDOZD\V
check the road conditions at all
WLPHV
Display and Control
Basic function
You can see the status of the Smart
Cruise Control operation in the Driving
Assist view on the cluster. Refer to “View
Modes” section in chapter 4.
Smart Cruise Control will be displayed
as below depending on the status of the
function.
„Operating„Temporarily canceled
ORG3EV071037NORG3EV071298N
[When operating
(1) Whether there is a vehicle ahead
and the selected distance level are
displayed.
(2) Set speed
(3) Whether there is a vehicle ahead and
the target vehicle distance
[When temporarily canceled
(1)
indicator
(2) The previous set speed is shaded.
(3) Whether there is a vehicle ahead (if
equipped)

Page:   < prev 1-10 ... 31-40 41-50 51-60 61-70 71-80 81-90 91-100 101-110 110 next >