Piston ring HONDA INTEGRA 1994 4.G Workshop Manual

k (81881
Ri RIKEN manutacture Piston ring
T:TEIKOKU PISTON RING manufacture piston ring
7scti
Unit of length: mm {in}
Engine Block {Bl6E1 englnel - sectlon
MEASUNEMENTSTANDARD (NEWI SERVICE LIMIT
bottom of skirt
Top
Second
oil--
top
Second
'....=-
lop
Ring to-groove clearance
Ring end gap
o.D.
Pin-to-piston clearance
Pin-to-rod interference
Smallend bore diameter
Large end bore diameter
End play installed on crankshatt
Main journal diameter
Warpage ot deck sLrrface
Bore diameter
Bore taPer
Reboring limit
Skirt O.D. at 15 mm (0.6 in)Irom
Clearance in cylinder
Groove width (For ring)
R
T
;
T
No. 1, 2, 4 and 5 journals
No. 3 iournal
Rod iournal diameter
Taper
Out-of round
End play
Runout
Main bearing-to-iournal oil clearance
No. 1, 2, 4 and 5 journals
No. 3 journal
Rod bearing to-iournal oil clearance
Second
oit R
T
Nominal
0.0710.003)max.
81.00 - 81.02 {3.189 - 3.190)
0.10 (0.004)
81.07(3.192)
0.05 (0.002)
0.25 (0.010)
Cylinder block
80.98 - 80.99 (3.188 - 3.189)
0.01 - 0.04 (0.0004 - 0.0016)
1.030 - r.010 (0.0406 0.0409)
1.230 - 1.210 (0.0484 - 0.0488)
2.805 - 2.820 (0.1104 0.1110)
80.9713.188)
0.05 (0.002)
1.0610.042)
1.26 (0.050)
2.8410.112\
Piston
0.045 - 0.070 {0.0018 - 0.0028}
0.040 - 0.065 (0.0016 - 0.0026)
0.045 - 0.070 (0.0018 - 0.0028)
0.13 {0.00s)
0.13 (0.00s)
0.13 (0.005)
0.60 {0.024)
0.60 10.024)
0.70 (0.028)
0.70 (0.028)
0.70 (0.028)
Piston ring
0.20 - 0.35 (0.008 - 0.014)
0.20 0.30 (0.008 - 0.012)
0.40 - 0.5s (0.0 r6 - 0.022)
0.20 - 0.s0 (0.008 - 0.020)
0.20 - 0.45 (0.008 - 0.0181
20.994 - 21.000 (0.8265 - 0.8268)
0.0r0 - 0.022 (0.0004 - 0.0009)
rrston rln
0.013 - 0.032 (0.0005 - 0.0013)
20.968 - 20.981 (0.825s - 0.8260)
48.0 (1.89)
0.1s - 0.30 (0.006 - 0.012)
Connecting rod
54.976 - 55.000 (2.1644 - 2.1654)
54.970 - 54.994 (2.1642 - 2.1651)
44.S76 - 45.000 {1.7707 - 1.7717}
0.00510.0002) max.
0.005 (0.0002) max.
0.10 - 0.35 (0.004 - 0.014)
0.03 (0.001) max.
0.010 (0.0004)
0.010 (0.0004)
0.45 (0.018)
0.04 {0.002)
Crankshaft
0.024 0.042 {0.0009 - 0.0017)
0.030 0.048 {0.0012 - 0.0019}
0.020 0.038 (0.0008 - 0.0015)
0.05010.0020)
0.060 (0.0024)
0.050 (0.0020)
Bearing
3-3

EBIk (818C1Section 7
Unit of length: mm (in)
ngrne ]'ocK (ltluur englnel -
MEASUREMENTSTANDARD (NEWI SERVIC€ LIMIT
Cyiinder blockwarpage of deck surlace
Bore diameter
Bore taPer
Reboring limit
0.05 (0.002) max.
81.00 - 81.02 {3.189 - 3.190)
0.08 (0.003)
81.0713.192)
0.05 (0.002)
0.25 (0.010)
PistonSkin O.D. ar 15 mm (0.6 in) {rom bottom ot skirt
Clearance in cylinder
Groove width (For ring) ToP
Socond
oil
80.98 - 80.99 13.188 - 3.189)
0.0r - 0.04 {0.0004 - 0.0016}
1.030 - 1.0,r0 {0.0406 - 0.0409)
1.230 - 1.240 (0.0484 - 0.0488)
2.805 - 2.820 (0.1104 - 0.11101
80.97 (3.188)
0.05 (0.002)
1.060 (0.0417)
1.260 (0.0496)
2.840 (0.1118)
Piston ringRing-to-pistongrooveclearance Top
Second
0.045 - 0.070 {0.0018 - 0.0028}
0.010 - 0.065 (0.0016 - 0.0026)
0.13 (0.005)
0.13 (0.005)
Ring end gap I oP
Socond
oil
0.20 - 0.35 {0.008 - 0.014)
0.40 - 0,55 (0.016 - 0.022)
0.20 - 0.s0 {0.008 - 0.020}
0.60 (0.024)
0.70 (0.028)
0.7010.0281
rrston rtno.D.
Pin-to-piston clearance
20.994 - 21.000 (0.8265 - 0.8268)
0.010 - 0.022 {0.0004 - 0.0009)
0.017 - 0.035 (0.0007 - 0.0014)
20.964 - 20.997 (0.8254 - 0.8267)
€.0 (1.89)
0.15 - 0.30 (0.006 - 0.012)
Connecting rodPin to-rod int€rference
Small end bore diameter
Large end bore diameter Nominal
End play installed on crankshaft
crankshatt
No. 1,2,4 and 5 iournals
No. 3 journal
Rod iournal diameter
Taper
Out'ol round
End play
Runout
Msin journal diameter
54.976 - 55.000 (2.1644 - 2.16541
54.974 - 54.998 (2.'|643 - 2.1553)
44.976 - 45.000 {1.7707 -'I.7717)
0.005 {0.0002} max.
0.004 {0.0002) max.
0.10 - 0.35 {0.00{ - 0.014)
0.020 (0.0008) max.
-t-oou
lo.ooort
EearingMain bsaring-to-journal oil clearance
No. 1, 2, 4 and 5 journals
No 3 journal
Rod bearing-to-journal oil clearanc€
0.024 - 0.042 (0.0009 - 0.0017)
0.030 - 0.048 (0.0012 - 0.0019)
0.032 - 0.050 (0.0013 - 0.0020)
0.050 (0.0020)
0.060 {0.0024)
0.060 (0.0024)
3-5

MEASUFEMENTSTANDARD I]{EWI
a gnmentCamber FrontRgarCaster FrontTotaltoe FrontRearFront whe€lturning angle Inward whe€lOutwsrd wh€el
-0. 10' 1 1.-0' 15' l$igl1. 10'r t"0i2(010.081rN 3:i (0.121ff)36' 0o' r 2'30. 30'
A1lc€lbearingEnd playFrontRoaa0 - 0.05 (0 - 0.002)0 - 0.05 {0 - 0.002}
Rim runout (Aluminum wheel) AxialRadialRim runout isteelwhgel) AxialRadisl
STANDARD INEWISEBVICE UMIT
0 - 0.7 {0 - 0.03)0 - 0.7 (0 - 0.03)0 - 1.0 {0 - 0.0{)0 - 1.0 (0 - 0.04)
2.0 (0.08)
1.5 (0.06)
2.0 (0.081
r.5 (0.061
SuspensionSestion 18
BrakeSection 19
Air ConditioningScction 22
.1: When using a new bek, adjust dellection or tension to new values. Run the engine tor 5 minules ihen turn it ott.
Readiust detlection or tension to lsed beh values.'2: 81881 engine'3: 818C1 engine
Unit of length: mm {in)
MEASUREMENTSTANDARD {NEWI
trrling brakePlay in strok€ at 200 N {20 kgf, 44 lbt)lever lorceTo b€ lockod when pulled 6 -10
nolchsa
; oot brake,adalPedal heighl lwith floor mat removod)
Free play
M/T160 (6.30)
155 (6.50)
1-5(0.04-0.20)
Vaster cylinderPiston-to-oushrod clearance0 - 0.4 (0 - 0.2)
f,,s4 brakeOisc thickness FrontRe6rDisc runout FrontR6arDisc parallolism Front and rear
Pad lhickness FrontRoar
STANDARD INEWISERVICE LIM]T
20.9 - 21.1 t0.82 - 0.83t8.9 - 9.1 {0.35 - 0.36)
9.5 - 10.5 {0.37 - 0.41}7.0- 8.0 {0.27 - 0.31)
19.0 (0.75)
8.0 (0.31)
0.10 (0.004)
0.r0 (0.00a)
0.015 (0.0006t
r.6 (0.06)
1.6 (0.06)
MEASUREMENTSTANDABO IT{EWI
Ar conditioningLubricant capacity mf (ll oz) Cond€nserEvaporatorLine or hoseReceiverLubricant type: NO-OlL8 {P/N 38899 - PR7 - A0l)
25 (5/6)
40 t1 1/3)10 (lBt
10 (1/31
CompressorLubricant capacity m{ (ll oz}Lubricant tvge: ND-O|L8 (P/N 38899 - PR7 - A01)Stator coil resistance at 68'F (20'C) 0Pulley-to-pressure plate clearance
140';u (4-23';")
3.4- 3.80.5 r 0.15 {0.02 r 0.006)
Compressorb€h'rDetlection with 98 N (10 kgf, 22 lbf)betlveen pulleys
7.5 - 9.5 {0.30 - 0.37)with used b€lt*'8.5 - 10.5 {0.33 - 0.41}with t/sod belt'35.0 - 7.0 {0.20 - 0.28) with new belt
Belt t€nsion N (kgf, lbl)Measured with belt lension gauge390 - 540 {r0 - 55, 88 - 120} with used beh*'340 - 490 {35 - 50, 77 - 110} with used belt*3740 - 880 {75 - 90, 170 - 200) with new belt
3-15

Valve Clearance
Adjustment lcont'dl
a
4.
Adjust valve clearances on No. 1 cylinder.
lntlkc: 0.08 - o.l2 mm (o.(Xxl - 0.qr5 in)
Exhru3t 0.16 - 0.20 mm {0.0,05 - 0.008 in}
Loosen lhe locknut and turn the adjusting screw
until feeler gauge slides back and fonh with a slight
amount of drag.
LOCKNUT9x0.?5mm25 N.m 12,5 kgf.m, 18lbt'ft|
6.
Tighten the locknut and recheck clearance again.
Repeat adjustment if necessary.
Rotate ths crankshaft 180" counte.clockwise(camshaft pulley turns 90'). The "UP" mark should
be on the exhaust side. Adjust valves on No. 3 cylin-
der.
I{umbcr 3 pidon !t TDC:
EXHAUST CAITISHAFTPULI,IY
INTAKE CAMSHAFTPULLEY
.UP' MANKS
7. Rotate the crankshaft 180'counterclockwis€ to
bring No. 4 piston to TDC. The'UP" mark should
be pointing straight down. Adjust valves on No. 4
cylinder.
Numb€r il piston at TDC:
8. Rotate the crankshaft 180' co u nie rclockwise to
bring No. 2 piston to TDC. The "UP" mark should
be on the intake side. Adjust valves on No. 2 cylin-
oer.
Numbor 2 pirton !t TDC:
NOTE: Refer to page 6-31 when installing cylindor hEEd
cover.
"UP'MARKS
-UP" MARKS

Valve Seals
Replacement (cylinder head removal not requiredl
NOTE: Cylinder head removal is not required in this
procedure.
The procodure shown below applies when using the in-
car valve spring compressor (Snap-on YA8845 with
Y AAA$-2A 718" attachment).
@@ whcn u3ing this tool, a: with any tool,
always u!€ agproved cyr Protcction. Using th.
right tool for cach iob hclps incraa3. produstivity
whilo 3ltrgu8rding tool!, cquipmcnt lnd the u3c1'
1. Turn the crankshaft so that the No. I and the No' 4
pistons are at top d€ad center (TDC).
2. Remove the cylinder head cover.
3. Remove the distributor.
4. Loosen and disconnect the timing belt from the
c8mshaft pulleys.
5. Remove the camshaft holde, bolts, then r€move the
camshaft holder, the camshaft and rocksr arms.
lntakc V!lv6 Sclls
6. Using the 6 mm bolts supplied with the tool, mount
the two up.ights to the cylinder head 8t the end
camshaft holde.s. The uprights fit as shown.
7. Insort the cross shaft through the bottom hole ot
the two up.ights.
6-5
OIL PASSAGE
OIL PASSAGES
Select the 7E in. diameter long compressor attach-
ment and fasten the attachment to the No. 4 hole of
the lever arm with the speed pin supplied.
Position the piston at TDC and insert an air adaptor
into th€ spark plug hole. Pump air into the cylinder
to keep the valv€ closed while cgmpressing springs
and removing the valve keepers.
Position the lever arm under the cross shaft so the
lever is psrpendicular to the shEft and ths compres-
sor attachment rests on toD of the rstainer for th€
spring being compressed. Use the rear position slot
on the lever as shown.
NOTE: Put shop towels over the oil passag€s to
prevent the valve keepers from falling into the cylin-
der h€ad.
(cont'd)

-
'14.
Valve Seals
Replacement (cylinder head removal not required) (cont'dl
'11.Using a downward motion on the lever arm. com-press the valve spring and remove the keepers from
the valve stem. Slowly release pressure on the
spring.
Repeat step l1 for the other valve in that cylinder.
Remove the valve seals (see page 6-22).
Installthe valve seals (see page 6-23).
Install the springs, the retainers and the keepers in
reverse order of removal.
16. Repeat steps 9 to l5 for the other three cylinders.
ExhaGt Valvs Soals
17. Using the 6 mm bolts supplied with the tool, mount
the two uprights to the cylinder head at the end
camshaft holders. The uprights fit as shown.
18. Insert the cross shaft through the bottom hole of
the two uprights.
Select the 7/8 in. diameter short compressor attach-ment and fasten the attachment to the No. 4 hole ofthe lever arm with the speed pin supplied.
Position the piston at TDC and insert an air adaptorinto the spark plug hole. Pump air into the cylinder
to keep the valve closed while compressing springs
and removing the valve keepers.
19.
20.
21. Position the lever arm unde. the cross shaft so thelever is perpendicular to the shaft and the compres-
sor attachment rests on top of the retainer for thespring being compressed. Use the rear position sloton the lever as shown.
NOTE: Put shop towels over the oil passages toprevent the valve keepers from falling into the cylin-der head.
Using a downward motion on the lever arm, com-press the valve spring and remove the keepers fromthe valve stem. Slowly release pressure on thespring.
Repeat step 22 for the other valve in that cylinder.
Remove the valve seals (see page 6-22).
Install the valve seals (see page 6-23).
Install the springs, the retainers and the keepers inreverse order of removal.
Repeat steps 20 to 26 on the other three cylinders.
NOTE: Reler to page 6-31 when installing cylinderneao cover.
OIL PASSAGE
27.

Timing Belt
Inspection
Remove the cylinder head cover.
. Reler to page 6-3'l when installing.
Inspect the timing belt for cracks and oil or coolant
soaking.
NOTE:
. Replace the belt if oil or coolant soaked.
. Rsmove any oil or solvent that gets on the belt.
Rotate pulley
and inspscr bell.
After inspecting, retorque the crankshaft pulley bolt
to 177 N'm ('18.0 kgf'm, 130 lbt'ft).
Tension Adjustment
CAUTION: Always Ediust timing belt tonsion with tho
cngin. cold.
NOTE:
. The tensionet is spring-loaded to apply proper ten-
sion to the belt automaticallv after making the follow-
ing adjustment.
. Always rotate the crankshaft counterclockwise when
viewed trom the pulley side Rotating it clockwise
may result in improper adjustment ot the belt ten-
sion.
Remove the cylinder head cover. (Refer to page
6-31 when installing.)
Set the No. 1 piston at TDC (see page 6-12).
Rotate the c.ankshaft 5 - 6 revolutions to set the
bslt.
4. Set the No. I piston at TDC.
3.
ADJUSNNG BOLT54 N.m (5.5 kqf.m,a0 rbr.ftlFor adiustment only,do not remove,
5.
6.
7.
8.
Direction olrolatlon.
Loosen the adiusting bolt 1/2 turn (180') onlv
Rotate the crankshaft counterclockwise 3-teeth on
the camshaft pulley.
Tighten the adjusting bolt to the specified torque.
After adjusting, retorque the crankshaft pulley bolt
to 177 N.m (18.0 kgl.m. 130 lbf.ft).
6-9

Timing Belt
Removal
I
NOTE:
. Turn the crankshaft pulley so the No. 1 piston is attop d6ad center (TDC) before removing the belt (see
page &12).
a Inspect the water pump when removed the timingbolt {see page 10-9}.
1. Remove thawhe€lwell splash shield (see page 6-18).
2. Loosen ths adjusting bolt and mounting bolts, thenremove the power steering {P/S) pump belt.
MOUivNNG BOLTS8 x 1.25 mm2a N.m 12.4 kgf.m, 1 7 lbt frl
Loosen the adjusting bolt and idler pulley bracket
bolt, then remove the air conditioning (A,/C) com-
oressor belt.
IDLER PUI.IEY BRACKETBOLTl0 r 1.25 mma/a N.m {1.5 kgf.m.33 lbf'ft}
AA,USNNG
ADJUSTING
4, Loosen the adjusting nut and mounting nut, thenremove the alt€rnator belt.
EELTa,l N.m {4.5 kgl.m,33 lbfftl
Remove the cruise control actuator (see page 6-18).
Remove the sid6 sngine mount.
10 x 1.25 mm52 N.m {5.3 kgr'm,38 lbtft}Replace.
MOUNTING NUT10 x 1.25 mm
ADJUSNNG NUT8 x 1.25 mrr2a N.m l2.a lef.m,17 rbl.ftl
12 x 1.25 mm74 N.m 17.5 kgt m,s4 tb{.ftl

Tightsn the locknut and recheck clearance again.
Rep6at sdjustm6nt if necossary.
Rotsts tha crankshaft 180' counterclockwiss
(c8mshaft pulley turns 90'). The "UP" mark should
be on th€ sxhaust 8id6, Adiust vslves on No. 3 cylin-
oer,
Nurrb.r3tittondTDC:
FEEI.IR GAUGE
.UP' MANKS
7. Rotato crankshaft 180' countsrclockwise to bring
No.4 piston to TDC. The "UP" mark should bo
pointing straight down. Adjust valves on No. 4
cylinder.
Numb.r 4 pidon .t Tt C:
8, Rotate crankshaft 180" counterclockwis€ to bring
No. 2 piston to TDC. The "UP" marks should be on
the intaks sid6. Adjust valves on No. 2 cylinder.
Nonb.r 2 pirton .l TltC:
NOTE: Refer to page 6-78 when installing cylinder head
cover.
6-45

Timing Belt
lnspection
Remove the cylinder head cover.
. Refer to page 6-78 when installing.
Inspect the timing belt for cracks and oil or coolant
soaking.
NOTE:
. Replace the belt if oil or coolant soaked.
. Remove any oil or solvent that gets onthe b€lt.
Rotate pulleyand inspect b6lt.
After inspecting. retorque the crankshaft pulley bolt
to 177 N.m (18.0 kgf.m, 130 lbf.ft).
Tension Adjustment
CAUTION: Always adlust timing bslt tsnsion with th6
engine cold.
NOTE:
. The tensioner is spring-loaded to apply proper ten-
sion to the belt automatically after making the follow-
ing adjustment.
a Alwavs rotate the crankshaft counterclockwise when
viewed trom the pulley side. Rotating it clockwise
may result in improper adjustment of the belt ten-
sion.
Remove the cylinder head cover. (Refer to page 6-
78 when installing.)
Set the No. 1 piston at TDC (see page 6-51).
Rotate the crankshaft 5-6 revolutions to set the belt.
Set the No. 1 piston at TDC.4.
AINUSTING AOLT5/a N.m 15.5 kg{.m, to lbtftlFor adjustment only,
5.
7.
8.
A
.//\v-/
Directionrotat|on,
Loosen the adjusting bolt 1/2 turn (180') only.
Rotate the crankshaft counterclockwise 3 teeth on
the camshaft pulley.
Tighten the adjusting bolr.
After adjusting, retorque the crankshaft pulley bolt
to 177 N.m (18.0 kgf.m, 130 lbf'ft).
6-48