ESP Hyundai Creta 2016 Owner's Guide

6-10
What to do in an emergency
Low tire pressure telltale /
TPMS malfunction indicator
Each tire, including the spare (if pro
vided), should be checked monthly
when cold and inflated to the inflation
pressure recommended by the vehi
cle manufacturer on the vehicle plac
ard or tire inflation pressure label. (If
your vehicle has tires of a different
size than the size indicated on the
vehicle placard or tire inflation pres
sure label, you should determine the
proper tire inflation pressure for
those tires.) As an added safety feature, your vehi
cle has been equipped with a tire
pressure monitoring system (TPMS)
that illuminates a low tire pressure
telltale when one or more of your tires
is significantly underinflated.
Accordingly, when the low tire pres
sure telltale illuminates, you should
stop and check your tires as soon as
possible, and inflate them to the prop
er pressure. Driving on a significantly
underinflated tire causes the tire to
overheat and can lead to tire failure.
Underinflation also reduces fuel effi
ciency and tire tread life, and may
affect the vehicle’s handling and stop
ping ability.
Please note that the TPMS is not a
substitute for proper tire maintenance,
and it is the driver’s responsibility to
maintain correct tire pressure, even if
underinflation has not reached the
level to trigger illumination of the
TPMS low tire pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not oper
ating properly. The TPMS malfunction
indicator is combined with the low tire
pressure telltale. When the system
detects a malfunction, the telltale will
flash for approximately one minute
and then remain continuously illumi
nated. This sequence will continue
upon subsequent vehicle startups as
long as the malfunction exists. When
the malfunction indicator is illuminat
ed, the system may not be able to
detect or signal low tire pressure as
intended. TPMS malfunctions may
occur for a variety of reasons, includ
ing the installation of replacement or
alternate tires or wheels on the vehi
cle that prevent the TPMS from func
tioning properly. Always check the
TPMS malfunction telltale after
replacing one or more tires or wheels
on your vehicle to ensure that the
replacement or alternate tires and
wheels allow the TPMS to continue to
function properly.
TIRE PRESSURE MONITORING SYSTEM (TPMS, IF EQUIPPED)
OGS066013L

6-26
What to do in an emergency
Your vehicle is equipped with emer
gency commodities to help you
respond to emergency situation.
Fire extinguisher
If there is small fire and you know
how to use the fire extinguisher, fol
low these steps carefully.
1. Pull out the safety pin at the top of the extinguisher that keeps the
handle from being accidentallypressed.
2. Aim the nozzle towards the base of the fire.
3. Stand approximately 2.5 m (8 ft) away from the fire and squeeze
the handle to discharge the extin
guisher. If you release the handle,
the discharge will stop.
4. Sweep the nozzle back and forth at the base of the fire. After the fire
appears to be out, watch carefully
since it may reignite.
First aid kit
Supplies for use in giving first aid
such as scissors, bandage and
adhesive tape, etc. are provided.
Triangle reflector
Place the triangle reflector on the
road to warn oncoming vehicles dur
ing emergencies, such as when the
vehicle is parked by the roadside due
to problems.
Tire pressure gauge
(if equipped)
Tires normally lose some air in day
today use, and you may have to add
a air periodically and usually it is not
a sign of a leaking tire, but of normal
wear. Always check tire pressure
when the tires are cold because tire
pressure increases with tempera
ture. To check the tire pressure, take the
following steps:
1. Unscrew the inflation valve cap
that is located on the rim of the
tire.
2. Press and hold the gauge against the tire valve. Some air will leak as
you begin and more will leak if you
don't press the gauge in firmly.
3. A firm nonleaking push will acti vate the gauge.
4. Read the tire pressure on the gauge to see whether the tire
pressure is low or high.
5. Adjust the tire pressure to the specified pressure. Refer to "Tires
and Wheels" in chapter 8.
6. Reinstall the inflation valve cap.
EMERGENCY COMMODITY (IF EQUIPPED)

7
Maintenance
7
Maintenance
­Engine­compartment .............................................7-3
Maintenance­services ...........................................7-5Owner's responsibility ......................................................7-5
Owner maintenance precautions ................................7-5
Owner­maintenance ...............................................7-8 Owner maintenance schedule ......................................7-8
Scheduled­maintenance­service ........................7-10
Explanation­of­scheduled­maintenance­items ..7-28
Engine­oil ..............................................................7-32 Checking the engine oil level ....................................7-32
Changing the engine oil and filter ..............................7-33
Engine­coolant......................................................7-34 Checking the coolant level ...........................................7-34
Recommended engine coolant.....................................7-36
Changing the coolant .....................................................7-36
Brake/clutch­fluid ................................................7-37 Checking the brake/clutch fluid level ........................7-37
Washer­fluid .........................................................7-39 Checking the washer fluid level ..................................7-39
Parking­brake .......................................................7-39 Checking the parking brake .........................................7-39
Fuel­filter­(For­Diesel) ........................................7-40 Draining water from fuel filter ....................................7-40
Extracting air from the fuel filter ..............................7-40 Air­cleaner ............................................................7-41
Filter replacement ........................................................7-41
Climate­control­air­filter .....................................7-42 Filter inspection ...............................................................7-42
Filter replacement ...........................................................7-42
Wiper­blades .........................................................7-44 Blade inspection ..............................................................7-44
Blade replacement ..........................................................7-44
Battery...................................................................7-47 For best battery service................................................7-47
Battery capacity label ....................................................7-49
Battery recharging .........................................................7-49
Reset items .......................................................................7-50
Tires­and­wheels ..................................................7-51 Tire care ............................................................................7-51
Recommended cold tire inflation pressures.............7-51
Checking tire inflation pressure ..................................7-53
Tire rotation .....................................................................7-54
Wheel alignment and tire balance ..............................7-55
Tire replacement .............................................................7-55
Wheel replacement ........................................................7-56
Tire traction ......................................................................7-57
Tire maintenance ...........................................................7-57
Tire sidewall labeling ......................................................7-57
Low aspect ratio tire ......................................................7-61
7

7-5
7
Maintenance
MAINTENANCE SERVICES
You should exercise the utmost care
to prevent damage to your vehicle
and injury to yourself whenever per
forming any maintenance or inspec
tion procedures. Inadequate, incom
plete or insufficient servicing may
result in operational problems with
your vehicle that could lead to vehi
cle damage, an accident, or person
al injury.Owner's responsibility
Information
Maintenance Service and Record
Retention are the owner's responsibility.
We recommend in general that you
have your vehicle serviced by an
authorized HYUNDAI dealer.
You should retain documents that
show proper maintenance has been
performed on your vehicle in accor
dance with the scheduled mainte
nance service charts shown on the
following pages. You need this infor
mation to establish your compliance
with the servicing and maintenance
requirements of your vehicle war
ranties.
Detailed warranty information is pro
vided in your Service Passport.
Repairs and adjustments required as
a result of improper maintenance or
a lack of required maintenance are
not covered when your vehicle is
covered by warranty.
Owner maintenance precautions
Improper or incomplete service may
result in problems. This chapter gives
instructions only for the maintenance
items that are easy to perform.
Information
Improper owner maintenance during
the warranty period may affect war
ranty coverage. For details, read the
separate Service Passport provided
with the vehicle. If you're unsure
about any servicing or maintenance
procedure, we recommend that the
system be serviced by an authorized
HYUNDAI dealer.i
i

7-6
Maintenance
•Do not put heavy objects or apply
excessive force on top of the
engine cover (if equipped) or fuel
related parts.
•When you inspect the fuel system
(fuel lines and fuel injection
devices), we recommend that you
contact an authorized HYUNDAI
dealer.
•Do not drive long time with
the engine cover (if equipped)
removed.
•When checking the engine room,
do not go near fire. Fuel, washer
fluid, etc. are flammable oils that
may cause fire.
•Before touching the battery, igni
tion cables and electrical wiring,
you should disconnect the battery
"" terminal. You may get an elec
tric shock from the electric current.
(Continued)
NOTICE
Maintenance work
•Performing maintenance work
on avehicle can be dangerous.
You can be seriously injured
while performing some mainte
nance procedures. If you lack
sufficient knowledge and experi
ence or the proper tools and
equipment to do the work, we
recommend that the system be
serviced by an authorized
HYUNDAI dealer.
•Working under the hood with the
engine running is dangerous. It
becomes even more dangerous
when you wear jewelry or loose
clothing. These can become
entangled in moving parts and
result in injury.
(Continued)
WARNING (Continued)
Therefore, if you must run the
engine while working under the
hood, make certain that you
remove all jewelry (especially
rings, bracelets, watches, and
necklaces) and all neckties,
scarves, and similar loose cloth
ing before getting near the engine
or cooling fans.
Do not leave gloves, rags or any
other combustible material in the
engine compartment. Doing so
may cause a heatinduced fire.
WARNING

7-58
Maintenance
Wheel size designation
Wheels are also marked with impor
tant information that you need if you
ever have to replace one. The follow
ing explains what the letters and
numbers in the wheel size designa
tion mean.
Example wheel size designation:
6.0JX16
6.0 Rim width in inches.
J Rim contour designation.
16 Rim diameter in inches.
Tire speed ratings
The chart below lists many of the dif
ferent speed ratings currently being
used for passenger car tires. The
speed rating is part of the tire size
designation on the sidewall of the
tire. This symbol corresponds to that
tire's designed maximum safe oper
ating speed.
3. Checking tire life (TIN : Tire
Identification Number)
Any tires that are over 6 years old,
based on the manufacturing date,
(including the spare tire) should be
replaced by new ones. You can find
the manufacturing date on the tire
sidewall (possibly on the inside of the
wheel), displaying the DOT Code.
The DOT Code is a series of num
bers on a tire consisting of numbers
and English letters. The manufactur
ing date is designated by the last four
digits (characters) of the DOT code.
DOT : XXXX XXXX OOOO
The front part of the DOT means a
plant code number, tire size and
tread pattern and the last four num
bers indicate week and year manu
factured.
For example:
DOT XXXX XXXX 1615 represents
that the tire was produced in the 16th
week of 2015.
S 180 km/h (112 mph) T 190 km/h (118 mph)
H 210 km/h (130 mph) V 240 km/h (149 mph) Z Above 240 km/h (149 mph)
W *270 km/h (168 mph)
Maximum SpeedSpeedRatingSymbol
* W speed rating is subcategory of the Z speed rating.

7-60
Maintenance
Tread wear
The tread wear grade is a compara
tive rating based on the wear rate of
the tire when tested under controlled
conditions on a specified govern
ment test course. For example, a tire
graded 150 would wear oneanda
half times (1) as well on the gov
ernment course as a tire graded 100.
The relative performance of tires
depends upon the actual conditions
of their use, however, and may
depart significantly from the norm
due to variations in driving habits,
service practices and differences in
road characteristics and climate.
These grades are molded on the
sidewalls of passenger vehicle tires.
The tires available as standard or
optional equipment on your vehicle
may vary with respect to grade.
Traction AA, A, B & C
The traction grades, from highest to
lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement measured
under controlled conditions on spec
ified government test surfaces of
asphalt and concrete. A tire marked
C may have poor traction perform
ance.
Temperature A, B & C
The temperature grades are A (the
highest), B, and C, representing the
tire’s resistance to the generation of
heat and its ability to dissipate heat
when tested under controlled condi
tions on a specified indoor laboratory
test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life, and
excessive temperature can lead to
sudden tire failure. Grades B and A
represent higher levels of perform
ance on the laboratory test wheel
than the minimum required by law.
The traction grade assigned to this
tire is based on straightahead
braking traction tests, and does
not include acceleration, corner
ing, hydroplaning, or peak traction
characteristics.
WARNING

7-78
Maintenance
lIGhT BulBS
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference between
the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burnedout
bulb with one of the same wattage
rating. Otherwise, it may cause dam
age to the fuse or electric wiring sys
tem.
NOTICE
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for automatic
transaxle vehicle) or neutral (for
manual transaxle vehicle), apply
the parking brake, place the igni
tion switch in the LOCK/OFF posi
tion, and take the key with you
when leaving the vehicle to avoid
sudden movement of the vehicle
and to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-89
7
Maintenance
APPEARANCE CARE
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for offroad
driving, you should wash it after each
offroad trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear andclean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may beused.
After washing, rinse the vehicle thor
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish. •Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
•Be careful when washing the side
windows of your vehicle.
Especially, with highpressure
water, water may leak through the
windows and wet the interior.
•To prevent damage to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter
gents.
NOTICE
Wet brakes
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired,
dry the brakes by applying them
lightly while maintaining a slow for
ward speed.
WARNING

8-7
8
Specifications & Consumer information
Recommended SAE viscosity
number
Engine oil viscosity (thickness) has
an effect on fuel economy and cold
weather operating (engine start and
engine oil flowability). Lower viscosi
ty engine oils can provide better fuel
economy and cold weather perform
ance, however, higher viscosity
engine oils are required for satisfac
tory lubrication in hot weather. Using
oils of any viscosity other than those
recommended could result in engine
damage. When choosing an oil, consider the
range of temperature your vehicle
will be operated in before the next oil
change.
Proceed to select the recommended
oil viscosity from the chart.
Always be sure to clean the area
around any filler plug, drain plug,
or dipstick before checking or
draining any lubricant. This is
especially important in dusty or
sandy areas and when the vehicle
is used on unpaved roads.
Cleaning the plug and dipstick
areas will prevent dirt and grit from
entering the engine and other
mechanisms that could be dam
aged.
CAUTION
Temperature Range for SAE Viscosity Numbers
Temperature°C
(°F) 3 0 2 0 1 0 0 1 0 2 0 3 0 4 0 5 0
1 0 0 2 0 4 0 6 0 8 0 1 0 0 1 2 0
Diesel
Engine Oil
5W30
15W40
10W30
0W30
* 1
: For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE 5W
20 (Except Middle East) or 5W30 (For Middle East). However, if the engine oil is not available in
your country, select the proper engine oil using th e engine oil viscosity chart.
* 2
: For middle East, do not use engine oil of viscosi ty grade SAE 5W20.
Gasoline
Engine Oil * 1
20W50
10W30
15W40
5W20*2, 5W30
20W50
10W30
15W40
5W30, 5W40
Except
Middle East
For
Middle East