ignition INFINITI QX56 2007 Factory Service Manual

AUDIO
AV-33
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of blown fuse before installing new fuse. Refer to PG-
3.
2.POWER SUPPLY CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner (factory installed) M41 connector.
3. Check voltage between the satellite radio tuner (factory installed) and ground.
OK or NG
OK >> GO TO 3.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness or connector.
3.GROUND CIRCUIT CHECK
1. Turn ignition switch OFF.
2. Inspect satellite radio tuner (factory installed) case ground.
3. Disconnect satellite radio tuner (factory installed) connector M41 (A) and audio unit connector M42 (B).
4. Check continuity between satellite radio tuner (factory installed) and audio unit.
OK or NG
OK >> Inspection End.
NG >> • Check connector housings for disconnected or loose
terminals.
• Repair harness, connector or satellite radio tuner (factory installed) case ground.
Satellite Radio Tuner (Factory Installed) Communication Circuit InspectionINFOID:0000000003533677
1.CHECK HARNESS - 1
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner (factory installed) connector M41 and audio unit connector M42.
Unit Terminals Signal name Fuse No.
Satellite radio tuner (factory in-
stalled)32 Battery power 31
36 Ignition switch ACC or ON 4
UnitTerminal No.
OFF ACC ON (+)
(-)
Connector Terminal
Satellite
radio tuner
(factory in-
stalled)M4132 GroundBattery
voltageBattery
voltageBattery
voltage
36 Ground 0VBattery
voltageBattery
voltage
WKIA4539E
Te r m i n a l s
Continuity Satellite radio tuner (factory in-
stalled)Audio unit
Connector Terminal Connector Terminal
A: M4125
B: M4245
Ye s
26 46
WKIA4540E

AV-34
< SERVICE INFORMATION >
AUDIO
3. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 28 and audio unit harness
connector M42 (B) terminal 48
4. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 28 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK HARNESS - 2
1. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 29 and audio unit harness
connector M42 (B) terminal 49
2. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 29 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3.CHECK HARNESS - 3
1. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 30 and audio unit harness
connector M42 (B) terminal 50
2. Check continuity between satellite radio tuner (factory installed)
harness connector M41 (A) terminal 30 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4.CHECK REQ1 SIGNAL
1. Connect satellite radio tuner (factory installed) connector and audio unit connector.
2. Turn ignition switch to ACC
3. Check signal between satellite radio tuner (factory installed) har-
ness connector M41 terminal 28 and ground with CONSULT-ll or
oscilloscope.
OK or NG
OK >> GO TO 5.Continuity should exist.
Continuity should not exist.
WKIA4541E
Continuity should exist.
Continuity should not exist.
WKIA4542E
Continuity should exist.
Continuity should not exist.
WKIA4543E
28 - Ground : Refer to AV-28, "Terminal
and Reference Value for Satel-
lite Radio Tuner (Factory In-
stalled)".
WKIA4544E

AUDIO
AV-35
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
NG >> Replace audio unit. Refer to AV-46, "Removal and Installation".
5.CHECK TXD SIGNAL
1. Check signal between satellite radio tuner (factory installed) har-
ness connector M41 terminal 29 and ground with CONSULT-ll or
oscilloscope.
OK or NG
OK >> GO TO 6.
NG >> Replace audio unit. Refer to AV-46, "
Removal and
Installation".
6.CHECK RXD SIGNAL
1. Check signal between satellite radio tuner (factory installed) har-
ness connector M41 terminal 30 and ground with CONSULT-ll or
oscilloscope.
OK or NG
OK >> Replace satellite radio tuner (factory installed). Refer to
AV-46, "
Removal and Installation".
NG >> Replace audio unit. Refer to AV-46, "
Removal and Installation".
Satellite Radio Tuner (Factory Installed) Left Channel Audio Signal Circuit Inspection
INFOID:0000000003533678
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner (factory installed) connector M41 (A) and audio unit connector M42 (B).
3. Check continuity between satellite radio tuner (factory installed) and audio unit.
4. Check continuity between satellite radio tuner (factory installed)
and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.29 - Ground : Refer to AV-28, "
Terminal
and Reference Value for Satel-
lite Radio Tuner (Factory In-
stalled)".
WKIA4545E
30 - Ground : Refer to AV-28, "Terminal
and Reference Value for Satel-
lite Radio Tuner (Factory In-
stalled)".
WKIA4546E
Te r m i n a l s
Continuity Satellite radio tuner (factory in-
stalled)Audio unit
Connector Terminal Connector Terminal
A: M4121
B: M4241
Ye s
22 42
Te r m i n a l s
Continuity Satellite radio tuner (factory installed)
—
Connector Terminal
A: M4121
Ground No
22
WKIA4547E

AV-36
< SERVICE INFORMATION >
AUDIO
2.CHECK LEFT CHANNEL AUDIO SIGNAL
1. Connect satellite radio tuner (factory installed) and audio unit.
2. Turn ignition switch ON.
3. Check signal between satellite radio tuner (factory installed)
connector M41 terminals 21 and 22 with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace satellite radio tuner (factory installed). Refer to
AV-46, "
Removal and Installation".
NG >> Replace audio unit. Refer to AV-46, "
Removal and Installation".
Satellite Radio Tuner (Factory Installed) Right Channel Audio Signal Circuit Inspection
INFOID:0000000003533679
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner (factory installed) connector M41 (A) and audio unit connector M42 (B).
3. Check continuity between satellite radio tuner (factory installed) and audio unit.
4. Check continuity between satellite radio tuner (factory installed)
and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2.CHECK RIGHT CHANNEL AUDIO SIGNAL
1. Connect satellite radio tuner (factory installed) and audio unit.
2. Turn ignition switch ON.21 - 22 : Refer to AV-28, "
Terminal
and Reference Value for Sat-
ellite Radio Tuner (Factory In-
stalled)".
WKIA4548E
Te r m i n a l s
Continuity Satellite radio tuner (factory in-
stalled)Audio unit
Connector Terminal Connector Terminal
A: M4123
B: M4243
Ye s
24 44
Te r m i n a l s
Continuity Satellite radio tuner (factory installed)
—
Connector Terminal
A: M4123
Ground No
24
WKIA4549E

AUDIO
AV-37
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
3. Check signal between satellite radio tuner (factory installed)
connector M41 terminals 23 and 24 with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace satellite radio tuner (factory installed). Refer to
AV-46, "
Removal and Installation".
NG >> Replace audio unit. Refer to AV-46, "
Removal and Installation".
Steering Switch CheckINFOID:0000000003533680
1.AV SWITCH SELF-DIAGNOSIS FUNCTION CHECK
1. Start AV switch self-diagnosis function. Refer to AV-28, "
AV Switch Self-Diagnosis Function".
2. Operate steering switch.
Does steering switch operate normally?
YES >> Inspection End.
NO >> GO TO 2.
2.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect AV switch connector M98 and spiral cable connector M30.
3. Check continuity between spiral cable harness connector terminal and AV switch harness connector ter-
minal.
4. Check continuity between AV switch and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness.
3.SPIRAL CABLE CHECK
1. Disconnect spiral cable connectors M30 and M102.23 - 24 : Refer to AV-28, "
Terminal
and Reference Value for Sat-
ellite Radio Tuner (Factory In-
stalled)".
WKIA4550E
Te r m i n a l s
Continuity Spiral cable AV switch
Connector Terminal Connector Terminal
M3032
M9813
Ye s 31 14
24 12
Te r m i n a l s
Continuity AV switch
—
Connector Terminal
M9812
Ground No 13
14
WKIA1600E

AUDIO
AV-39
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
Sound Is Not Heard from Front Door Speaker or Front TweeterINFOID:0000000003533683
1.HARNESS CHECK
1. Disconnect BOSE speaker amp. connector M113 and suspect speaker connector.
2. Check continuity between BOSE speaker amp. harness connec-
tor terminal M113 and suspect speaker harness connector ter-
minal.
3. Check continuity between BOSE speaker amp. harness connec-
tor terminal M113 and ground.
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.FRONT SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M113 and suspect speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
Te r m i n a l s
Continuity BOSE speaker amp. Speaker or tweeter
Connector Terminal Connector Terminal
M11313
D12+
Ye s 14 -
15
D112+
16 -
13
M109+
14 -
15
M 111+
16 -
Te r m i n a l s
Continuity BOSE speaker amp.
—
Connector Terminal
M11313
Ground No 14
15
16
WKIA2018E

AV-40
< SERVICE INFORMATION >
AUDIO
4. Check the signal between BOSE speaker amp. harness connec-
tor M113 terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace suspect speaker. Refer to AV-46, "Removal
and Installation" or AV-46, "Removal and Installation".
NG >> GO TO 3.
3.HARNESS CHECK
1. Disconnect audio unit connector M43 and BOSE speaker amp. connector M113.
2. Check continuity between audio unit harness connector termi-
nals and BOSE speaker amp. harness connector terminals.
3. Check continuity between audio unit harness connector terminal
and ground.
OK or NG
OK >> GO TO 4.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
4.FRONT SPEAKER SIGNAL CHECK
1. Connect audio unit connector and BOSE speaker amp. connector.
2. Turn ignition switch ACC.
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nectorTe r m i n a lCon-
nectorTe r m i n a l
M11313
M11314
Re-
ceive
audio
signal 15 16
WKIA4555E
SKIA0177E
Te r m i n a l s
Continuity Audio unit BOSE speaker amp.
Connector Terminal Connector Terminal
M431
M11329
Ye s 230
327
428
Te r m i n a l s
Continuity Audio unit
—
Connector Terminal
M431
Ground No 2
3
4
SKIA4284E

AV-42
< SERVICE INFORMATION >
AUDIO
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.REAR SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M113 and suspect speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between BOSE speaker amp. harness connec-
tor M113 terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace suspect speaker. Refer to AV-46, "Removal
and Installation" or AV-46, "Removal and Installation".
NG >> GO TO 3.
3.HARNESS CHECK
1. Disconnect audio unit connector M44 and BOSE speaker amp. connector M113.
Te r m i n a l s
Continuity BOSE speaker amp.
—
Connector Terminal
M1139
Ground No 10
11
12
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nec-
torTe r m i n a lCon-
nec-
torTe r m i n a l
M1139
M11310
Re-
ceive
audio
signal 11 1 2
WKIA4557E
SKIA0177E

AUDIO
AV-43
< SERVICE INFORMATION >
C
D
E
F
G
H
I
J
L
MA
B
AV
N
O
P
2. Check continuity between audio unit harness connector M44 ter-
minals and BOSE speaker amp. harness connector M113 termi-
nals.
3. Check continuity between audio unit harness connector terminal
and ground.
OK or NG
OK >> GO TO 4.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
4.REAR SPEAKER SIGNAL CHECK
1. Connect audio unit connector M44 and BOSE speaker amp. connector M113.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit harness connector M44
terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace BOSE speaker amp. Refer to AV-46, "Removal
and Installation".
NG >> Replace audio unit. Refer to AV-46, "
Removal and
Installation".
Te r m i n a l s
Continuity Audio unit BOSE speaker amp.
Connector Terminal Connector Terminal
M4413
M11325
Ye s 14 26
15 23
16 24
Te r m i n a l s
Continuity Audio unit
—
Connector Terminal
M4413
Ground No 14
15
16
SKIA4315E
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nectorTe r m i -
nalCon-
nectorTe r m i n a l
M4414
M4413
Re-
ceive
audio
signal 16 15
WKIA4558E
SKIA0177E

AV-44
< SERVICE INFORMATION >
AUDIO
Sound Is Not Heard from Center Speaker
INFOID:0000000003533685
1.HARNESS CHECK
1. Disconnect BOSE speaker amp. connector M112 and center speaker connector M110.
2. Check continuity between BOSE speaker amp. harness connec-
tor M112 terminals and center speaker harness connector M110
terminals.
3. Check continuity between BOSE speaker amp. harness connec-
tor M112 terminals and ground.
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.CENTER SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M112 and center speaker connector M110.
2. Turn ignition switch to ACC.
3. Push the “POWER” switch.
4. Check the signal between BOSE speaker amp. harness connec-
tor M112 terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace center speaker. Refer to AV-46, "Removal and Installation".
NG >> Replace BOSE speaker amp. Refer to AV-46, "
Removal and Installation".
Sound Is Not Heard from SubwooferINFOID:0000000003533686
1.CHECK FUSE
Te r m i n a l s
Continuity BOSE speaker amp. Center speaker
Connector Terminal Connector Terminal
M1122
M110-
Ye s
18 +
Te r m i n a l s
Continuity BOSE speaker amp.
—
Connector Terminal
M1122
Ground No
18
WKIA1222E
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nec-
torTe r m i n a lCon-
nec-
torTe r m i n a l
M112 18 M112 2Re-
ceive
audio
signal
WKIA1223E
SKIA0177E