cruise control INFINITI QX56 2011 Factory Manual PDF

DAS
ADAS CONTROL UNITDAS-93
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
ECU DIAGNOSIS INFORMATION
ADAS CONTROL UNIT
Reference ValueINFOID:0000000006223510
VALUES ON THE DIAGNOSIS TOOL
Monitor item Condition Value/Status
MAIN SW Ignition switch ON When MAIN switch is pressed On
When MAIN switch is not pressed Off
SET/COAST SW Ignition switch ON When SET/COAST switch is pressed On
When SET/COAST switch is not pressed Off
CANCEL SW Ignition switch ON When CANCEL switch is pressed On
When CANCEL switch is not pressed Off
RESUME/ACC SW Ignition switch ON When RESUME/ACCELERATE
switch is pressed On
When RESUME/ACCELERATE switch is not pressed Off
DISTANCE SW Ignition switch ON When DISTANCE swit
ch is pressed On
When DISTANCE switch is not pressed Off
CRUISE OPE Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When ICC system is controlling On
When ICC system is not controlling Off
BRAKE SW Ignition switch ON When brake pedal is depressed Off
When brake pedal is not depressed On
STOP LAMP SW Ignition switch ON When brake pedal is depressed On
When brake pedal is not depressed Off
IDLE SW Engine running Idling On
Except idling (depress accelerator pedal) Off
SET DISTANCE  Start the engine and turn the
ICC system ON
 Press the DISTANCE switch to change the vehi-
cle-to-vehicle distance set-
ting When set to “long” Long
When set to “middle” Mid
When set to “short” Short
CRUISE LAMP Start the engine and press
MAIN switch ICC system ON
(MAIN switch indicator ON)
On
ICC system OFF
(MAIN switch indicator OFF) Off
OWN VHCL Start the engine and press
MAIN switch ICC system ON
(Own vehicle indicator ON)
On
ICC system OFF
(Own vehicle indicator OFF) Off
VHCL AHEAD Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When a vehicle ahead is detected (vehicle ahead de-
tection indicator ON)
On
When a vehicle ahead is not detected (vehicle ahead
detection indicator OFF) Off
ICC WARNING Start the engine and press
MAIN switch When ICC system is malfunctioning
(ICC system warning lamp ON)
On
When ICC system is normal
(ICC system warning lamp OFF) Off
Revision: 2010 May2011 QX56

DAS
ADAS CONTROL UNITDAS-95
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
GEAR While driving Displays the
gear position
MODE SIG Start the engine and press
MAIN switch When ICC system is deactivated Off
When vehicle-to-vehicle distance control mode is acti-
vated
ICC
When conventional (fixed speed) cruise control mode is
activated ASCD
SET DISP IND  Drive the vehicle and acti-
vate the conventional (fixed
speed) cruise control mode
 Press SET/COAST switch SET switch indicator ON On
SET switch indicator OFF Off
DISTANCE Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When a vehicle ahead is detected
Displays the dis-
tance from the
preceding vehi- cle
When a vehicle ahead is not detected 0.0
RELATIVE SPD Drive the vehicle and activate
the vehicle-to-vehicle distance
control mode When a vehicle ahead is detected
Displays the rel-
ative speed.
When a vehicle ahead is not detected 0.0
DYNA ASIST SW Ignition switch ON When dynamic driver assistance switch is pressed On
When dynamic driver assistance switch is not pressed Off
DCA ON IND Start the engine and press dy-
namic driver assistance switch
(When DCA setting is ON) DCA system OFF
(DCA system switch indicator OFF)
Off
DCA system ON
(DCA system switch indicator ON) On
DCA VHL AHED Drive the vehicle and activate
the DCA system When a vehicle ahead is not detected (vehicle ahead
detection indicator OFF)
Off
When a vehicle ahead is detected (vehicle ahead de-
tection indicator ON) On
IBA SW Ignition switch ON When the IBA OFF switch is pressed On
When the IBA OFF switch is not pressed Off
FCW SYSTEM ON Ignition switch ON When the FCW system is ON
(Warning systems ON indicator ON)
On
When the FCW system is OFF
(Warning systems ON indicator OFF) Off
APA TEMP Engine running Display the ac-
celerato
r pedal
actuator inte- grated motor temperature
APA PWR Ignition switch ON Power supply
voltage value of
accelerator ped- al actuator
LDW SYSTEM ON Ignition switch ON When the LDW system is ON
(Warning systems ON indicator ON)
On
When the LDW system is OFF
(Warning systems ON indicator OFF) Off
LDW ON LAMP Ignition switch ON Warning systems ON indicator ON On
Warning systems ON indicator OFF Off
Monitor item Condition Value/Status
Revision: 2010 May2011 QX56

DAS-98
< ECU DIAGNOSIS INFORMATION >[DCA]
ADAS CONTROL UNIT
Fail-safe
INFOID:0000000006223511
If a malfunction occurs in each system, ADAS contro l unit cancels each control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
1
(V/W)
Ground Warning systems
switch
InputIgnition
switch ON When warning systems
switch is not pressed
12 V
When warning systems
switch is pressed 0 V
3
(R/Y) IBA OFF switch Input Ignition
switch
ON When IBA OFF switch is
not pressed
12 V
When IBA OFF switch is
pressed 0 V
4
(LG/B) Warning systems ON
indicator
OutputIgnition
switch ON Warning systems ON indi-
cator ON
0 V
Warning systems ON indi-
cator OFF 12 V
5
(R) ICC brake hold relay
drive signal
OutputIgnition
switch ON —12 V
At “STOP LAMP” test of
“Active test” 0 V
6
(B) Ground — Ignition
switch ON —0 V
7
(L) ITS communication-H — — — —
8
(Y) ITS communication-L — — — —
12
(G/R) Warning buzzer signal Output Ignition
switch ON Warning buzzer operation 0 V
Warning buzzer not oper-
ating
12 V
14
(L) CAN -H — — — —
15
(P) CAN -L — — — —
16
(W/G) Ignition power supply Input Ignition switch ON Battery Voltage
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warn
ing lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
tone
ICC system warn
ing lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
toneIBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
toneIBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
tone
ICC system warn
ing lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Revision: 2010 May2011 QX56

DAS
ADAS CONTROL UNITDAS-101
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
 IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 39, it is fixed to 39 unt il the self-diagnosis results are erased.
Other than CAN communication s ystem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunc tion is detected again in the process.
- If it is over 49, it is fixed to 49 unt il the self-diagnosis results are erased.
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp BSW warning lamp
System
C1A00 0 CONTROL UNIT ON ON ON ON A, B, C, D, E, F, G DAS-129
C1A01 1 POWER SUPPLY CIR ON ON ON ON A, B, C, D, E, F, GDAS-130
C1A02 2 POWER SUPPLY CIR 2 ON ON ON ON A, B, C, D, E, F, GDAS-130
C1A03 3 VHCL SPEED SE CIRC ON ON ON ON A, B, C, D, E, F, GDAS-131
C1A04 4 ABS/TCS/VDC CIRC ON ON ON A, B, C, D, E, FDAS-133
C1A05 5 BRAKE SW/STOP L SW ON ON ON A, B, C, D, E, FDAS-134
C1A06 6 OPERATION SW CIRC ON ON A, B, E, FDAS-138
C1A12 12LASER BEAM OFFCN-
TR ON ON A, C, D, E
DAS-140
C1A13 13 STOP LAMP RLY FIX ON ON A, B, C, D, E DAS-141
C1A14 14 ECM CIRCUIT ON ON A, B, E, FDAS-147
C1A15 15 GEAR POSITION ON ON ON ON A, B, C, D, E, F, GDAS-148
C1A16 16 RADAR STAIN ON ON A, C, D, EDAS-150
C1A17 17 ICC SENSOR MALF ON ON A, B, C, D, EDAS-151
C1A18 18 LASER AIMING INCMP ON ON A, C, D, EDAS-152
C1A21 21ICC SENSOR HIGH
TEMP ON ON A, B, C, D, E
DAS-153
C1A24 24 NP RANGE ON ON ON ON A, B, C, D, E, F, G DAS-154
C1A26 26 ECD MODE MALF ON ON A, B, C, D, EDAS-156
C1A27 27 ECD PWR SUPLY CIR ON ON A, B, C, D, EDAS-157
C1A33 33CAN TRANSMISSION
ERR ON A, B, E
DAS-159
Revision: 2010 May2011 QX56

DAS-102
< ECU DIAGNOSIS INFORMATION >[DCA]
ADAS CONTROL UNIT
C1A34 34 COMMAND ERROR ON A, B, E
DAS-160
C1A35 35 APA CIR ON A, EDAS-161
C1A36 36 APA CAN COMM CIR ON A, EDAS-162
C1A37 133 APA CAN CIR 2 ON A, B, EDAS-163
C1A38 132 APA CAN CIR 1 ON A, B, EDAS-164
C1A39 39 STRG SEN CIR ON ON ON A, B, C, D, E, GDAS-165
C1A40 40 SYSTEM SW CIRC ON C, DCCS-126
C1A2A 80 ICC SEN PWR SUP CIR ON ON A, C, D, E DAS-158
C1B00 81 CAMERA UNIT MALF ON FDAS-361
C1B01 82 CAM AIMING INCMP ON FDAS-363
C1B03 83CAM ABNRML TMP DE-
TCT BLINK F
DAS-365
C1B53 84 SIDE RDR R MALF ON G DAS-482
C1B54 85 SIDE RDR L MALF ON GDAS-483
C1F01 91 APA MOTOR MALF ON A, EDAS-166
C1F02 92 APA C/U MALF ON A, EDAS-168
C1F05 95 APA PWR SUPLY CIR ON A, EDAS-171
NO DTC IS
DETECTED.
FURTHER TESTING
MAY BE RE-
QUIRED 55
NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED ———— — —
U0121 127 VDC CAN CIR 2 ON ON ON ON A, B, C, D, E, F, G DAS-175
U0126 130 STRG SEN CAN CIR 1 ON ON ON A, B, C, D, E, GDAS-176
U0235 144 ICC SENSOR CAN
CIRC 1 ON ON A, B, C, D, E
DAS-177
U0401 120 ECM CAN CIR 1 ON ON ON A, B, E, F, G DAS-178
U0402 122 TCM CAN CIR 1 ON ON ON ON A, B, C, D, E, F, GDAS-179
U0415 126 VDC CAN CIR 1 ON ON ON ON A, B, C, D, E, F, GDAS-180
U0428 131 STRG SEN CAN CIR 2 ON ON ON A, B, C, D, E, GDAS-181
U1000NOTE100 CAN COMM CIRCUIT ON ON ON ON A, B, C, D, E, F, GDAS-182
U1010 110 CONTROL UNIT (CAN) ON ON ON ON A, B, C, D, E, F, G DAS-184
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp
BSW warning lamp
System
Revision: 2010 May2011 QX56

DAS
ADAS CONTROL UNITDAS-103
< ECU DIAGNOSIS INFORMATION > [DCA]
C
D
E
F
G H
I
J
K L
M B
N P A
NOTE:
With the detection of “U1000” some syst ems do not perform the fail-safe operation.
A system controlling based on a signal received from the control unit performs fail-safe operation when the
communication with the ADAS control unit becomes inoperable.
U1500 145 CAM CAN CIR 2 ON F DAS-381
U1501 146 CAM CAN CIR 1 ON FDAS-382
U1502 147ICC SEN CAN COMM
CIR ON ON A, B, C, D, E
DAS-189
U1503 150 SIDE RDR L CAN CIR 2 ON G DAS-502
U1504 151 SIDE RDR L CAN CIR 1 ON GDAS-503
U1505 152 SIDE RDR R CAN CIR 2 ON GDAS-504
U1506 153 SIDE RDR R CAN CIR 1 ON GDAS-505
U1507 154LOST COMM (SIDE
RDR R) ON G
DAS-506
U1508 155LOST COMM (SIDE
RDR L) ON G
DAS-507
U150B 157 ECM CAN CIRC 3 ON ON ON A, B, E, F, G DAS-185
U150C 158 VDC CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, G DAS-186
U150D 159 TCM CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, GDAS-187
U150E 160 BCM CAN CIRC 3 ON ON ON A, B, E, F, GDAS-188
U150F 161 AV CAN CIRC 3 DAS-61
U1512 162 HVAC CAN CIRC3 ON FDAS-383
U1513 163 METER CAN CIRC 3 ON ON ON ON A, B, C, D, E, F, GDAS-190
U1514 164 STRG SEN CAN CIRC 3 ON ON ON A, B, C, D, E, GDAS-191
U1515 165 ICC SENSOR CAN
CIRC 3 ON ON A, B, C, D, E
DAS-192
U1516 166 CAM CAN CIRC 3 ON F DAS-385
U1517 167 APA CAN CIRC 3 ON A, B, EDAS-193
U1518 168 SIDE RDR L CAN CIRC 3 ON GDAS-510
U1519 169SIDE RDR R CAN CIRC
3 ON G
DAS-511
U1520 176 4WD CAN CIRC 3 ON ON ON A, B, C, D, E, F DAS-194
Systems for fail-safe
 A: Vehicle-to-vehicle distance control mode
 B: Conventional (fixed speed) cruise control mode
 C: Intelligent Brake Assist (IBA)
 D: Forward Collision Warning (FCW)
 E: Distance Control Assist (DCA)
 F: Lane Departure Warning (LDW)/Lane Departure Prevention (LDP)
 G: Blind Spot Warning (BSW)
DTC
CONSULT-III display Warning lamp Fail-safe
Reference
CONSULT-III On board
display
ICC system warning lamp
IBA OFF indicator lamp
Lane departure warning lamp BSW warning lamp
System
Revision: 2010 May2011 QX56

DAS-106
< ECU DIAGNOSIS INFORMATION >[DCA]
ICC SENSOR
×
: Applicable
DTC
CONSULT-III display
ICC system warning lamp
Fail-safe function Reference
CONSULT-III
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode
Distance Control Assist (DCA)
Forward Collision Warning (FCW) Intelligent Brake Assist (IBA)
Brake Assist (with preview function)
C1A00 CONTROL UNIT ON ××××××CCS-83
C1A01 POWER SUPPLY CIR ON ××××××CCS-85
C1A02 POWER SUPPLY CIR2 ON ××××××CCS-85
C1A12 LASER BEAM OFFCNTR ON ×××××CCS-96
C1A16 RADAR STAIN ON ×××××CCS-106
C1A18 LASER AIMING INCMP ON ×××××CCS-109
C1A21 UNIT HIGH TEMP ON ××××××CCS-111
C1A39 STRG SEN CIR ON ××××××CCS-124
C1A50 ADAS MALFUNCTION ON ××××××CCS-128
U0104 ADAS CAN CIR1 ON ××××××CCS-132
U0121 VDC CAN CIR2 ON ××××××CCS-133
U0126 STRG SEN CAN CIR1 ON ××××××CCS-135
U0405 ADAS CAN CIR2 ON ××××××CCS-140
U0415 VDC CAN CIR1 ON ××××××CCS-141
U0428 STRG SEN CAN CIR2 ON ××××××CCS-143
U1000 CAN COMM CIRCUIT ON ××××××CCS-145
U1010 CONTROL UNIT (CAN) ON ××××××CCS-147
Revision: 2010 May2011 QX56

DAS-198
< SYMPTOM DIAGNOSIS >[DCA]
SWITCH DOES NOT TURN ON /
SWITCH DOES NOT TURN OFF
SWITCH DOES NOT TURN ON / SWITCH DOES NOT TURN OFF
DescriptionINFOID:0000000006223651
The switch does not turn ON
 When the DCA system setting is ON, the DCA system switch indicator does not illuminate even if the
dynamic driver assistance switch is depressed.
The switch does not turn OFF
 The DCA system switch indicator does not turn OFF even if the dynamic driver assistance switch is pressed
when the DCA system switch indicator illuminates.
NOTE:
The system cannot be operated when setting conv entional (fixed speed) cruise control mode.
Diagnosis ProcedureINFOID:0000000006223652
1.CHECK DCA SYSTEM SETTING
1. Start the engine.
2. After starting the engine wait for 5 seconds or more.
3. Check that DCA system setti ng on the navigation screen is ON.
Is DCA system setting ON?
YES >> GO TO 2.
NO >> Enable the DCA system setting.
2.DYNAMIC DRIVER ASSISTA NCE SWITCH INSPECTION
1. Start the engine.
2. Check that “DYNA ASIST SW” operates normally in “DATA MONITOR” of “ICC/ADAS” with CONSULT-III.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK DCA SYSTEM SWITCH INDICATOR CIRCUIT
1. Start the engine.
2. Select the active test item “DCA IN DICATOR” of “ICC/ADAS” with CONSULT-III.
3. Check if the DCA system switch indicator illuminates when the test item is operated.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 4.
4.PERFORM THE SELF-DIAGNOSIS OF COMBINATION METER
1. Perform “All DTC Reading” with CONSULT-III.
2. Check if the DTC is detected in self-d iagnosis results of “METER/M&A”. Refer to MWI-43, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 6.
5.CHECK STEERING SWITCH CIRCUIT
Check the steering switch circuit. Refer to DAS-138, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 7.
6.PERFORM THE SELF-DIAGNOSIS
1. Perform “All DTC Reading” with CONSULT-III.
2. Check if the DTC is detected in self-diagnosis results of “ICC/ADAS”. Refer to DAS-100, "
DTC Index".
Is any DTC detected?
YES >> GO TO 7.
Revision: 2010 May2011 QX56

DAS
SYSTEM
DAS-219
< SYSTEM DESCRIPTION >[FCW]
C
D
E
F
G H
I
J
K L
M B
N P A
 The FCW system will function when own vehicle is dr iven at speeds of approximately 15 km/h (10 MPH) and
above.
NOTE:
The FCW system shares the di agnosis function with ICC system.
FUNCTION DESCRIPTION
The distance from the vehicle ahead and a relative speed are calculated by using the ICC sensor and an ICC
sensor signal is transmitted to t he ADAS control unit via ITS communi cation. When judging the necessity of
warning according to the received vehicle ahead detection signal, the ADAS control unit transmits a buzzer
output signal and meter display signal to the combination meter via CAN communication.
FCW Operating Condition
 Warning systems ON indicator: ON
 Vehicle speed: Approximately 15 km/h (10 MPH) and above.
Fail-safe Indication
FCW INITIAL STATE CHANGE
CAUTION:
Never change FCW initial state “ON” ⇒ “OFF” without the con sent of the customer.
FCW initial state can be changed.
 FCW initial ON* - FCW function is automatically turned ON, when the ignition switch OFF ⇒ ON.
 FCW initial OFF - FCW function is still OFF when the ignition switch OFF ⇒ ON.
*: Factory setting
How to change FCW/LDW/BSW initial state1. Turn ignition switch ON.
2. Warning systems switch is OFF.
3. Push and hold warning systems switch for more than 4 seconds.
4. Buzzer sounds and blinking of the warning systems ON indicator informs that the FCW/LDW/BSW initial
state change is completed.
Fail-safe (ADAS Control Unit)INFOID:0000000006223674
If a malfunction occurs in each s ystem, ADAS control unit cancels eac h control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
Vehicle condition Indication on the combination meter
 When the FCW system malfunctions
 When the sensor window is dirty
 When driving into a strong light (i.e. sunlight)
NOTE:
Check that the IBA system is not OFF. The indicator lamp is shared
with IBA system.
JPOIA0179ZZ
System Buzzer Warning lamp/Indicator lamp Description
Vehicle-to-vehicle distance control mode High-pitched
toneICC system warning lamp Cancel
Conventional (fixed speed) cruise control mode High-pitched
toneICC system warning lamp Cancel
Intelligent Brake Assist (IBA) High-pitched
tone
IBA OFF indicator lamp Cancel
Forward Collision Warning (FCW) High-pitched
tone
IBA OFF indicator lamp Cancel
Distance Control Assist (DCA) High-pitched
toneICC system warning lamp Cancel
Lane Departure Warning (LDW) — Lane departure warning lamp Cancel
Revision: 2010 May2011 QX56

DAS-226
< SYSTEM DESCRIPTION >[FCW]
DIAGNOSIS SYSTEM (ADAS CONTROL UNIT)
NOTE:
 Causes of the maximum five cancella
tions (system cancel) are displayed.
 The displayed cancellation causes display the number of the ignition switch ON/OFF up to 254. It is fixed to
254 if it is over 254. It returns to 0 when the same cancellation cause is detected again.
Display Items for The Cause of Automatic Cancellation 1
Work support items Description
CAUSE OF AUTO-CANCEL 1 Displays causes of automatic system cancellation occurred during control of the following sys-
tems
 Vehicle-to-vehicle distance control mode
 Conventional (fixed speed) cruise control mode
 Distance Control Assist (DCA)
CAUSE OF AUTO-CANCEL 2 Displays causes of automatic system cancellation occurred during control of the Lane Depar-
ture Prevention (LDP) system
Cause of cancellation
Vehicle-to-vehicle distance control mode
Conventional (fixed speed) cruise control mode Distance Control Assist
Description
OPERATING WIPER ×The wiper operates at HI (it includes when the wiper is operated at
HI with the wiper switch AUTO position)
OPERATING ABS ××ABS function was operated
OPERATING TCS ×××TCS function was operated
OPERATING VDC ×××VDC function was operated
ECM CIRCUIT ××ECM did not permit ICC operation
OPE SW VOLT CIRC ×××The ICC steering switch input voltage is not within standard range
LASER SUNBEAM ××Intense light such as sunlight entered ICC sensor light sensing part
LASER TEMP ××Temperature around ICC sensor became low
SNOW MODE SW ××SNOW mode switch was pressed
OP SW DOUBLE
TOUCH ××
ICC steering switches were pressed at the same time
VHCL SPD DOWN ×××Vehicle speed lower than the speed as follows
 Vehicle-to-vehicle distance control mode is 24 km/h (15 MPH)
 Conventional (fixed speed) cruise control mode is 32 km/h (20
MPH)
WHL SPD ELEC NOISE ×××Wheel speed sensor signal caught electromagnetic noise
VDC/TCS OFF SW ××VDC OFF switch was pressed
VHCL SPD UNMATCH ×××Wheel speed became different from A/T vehicle speed
TIRE SLIP ××Wheel slipped
IGN LOW VOLT ×××Decrease in ADAS control unit IGN voltage
PARKING BRAKE ON ××The parking brake is operating
WHEEL SPD UNMATCH ×××The wheel speeds of 4 wheels are out of the specified values
Revision: 2010 May2011 QX56