Fuel INFINITI QX56 2011 Factory Manual Online

EC-70
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
ACTIVE TEST MODE
Test Item
ECM TEMP 1
°C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 1.
ECM TEMP 2 °C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 2.
FUEL PUMP DUTY %  The control condition of the fuel pump control mod-
ule (FPCM) (determined by ECM according to the
input signals) is indicated.
Monitored item Unit Description Remarks
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
VENT CON-
TROL/V  Ignition switch: ON (Engine
stopped)
 Turn solenoid valve ON and OFF with the CONSULT-III and listen
to operating sound. Solenoid valve makes an operating
sound.
 Harness and connectors
 Solenoid valve
ENG COOLANT
TEMP  Engine: Return to the original
non-standard condition
 Change the engine coolant tem- perature using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.  Harness and connectors
 Engine coolant temperature sen-
sor
 Fuel injector
FUEL INJEC-
TION  Engine: Return to the original
non-standard condition
 Change the amount of fuel injec- tion using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Fuel injector
 Air fuel ratio (A/F) sensor 1
FUEL/T TEMP
SEN  Change the fuel tank temperature using CONSULT-III.
PURG VOL
CONT/V  Engine: After warming up, run en-
gine at 1,500 rpm.
 Change the EVAP canister purge
volume control solenoid valve
opening percent using CON-
SULT-III. Engine speed changes according to
the opening percent.
 Harness and connectors
 Solenoid valve
FAN DUTY CON-
TROL* Ignition switch: ON
 Change duty ratio using CON-
SULT-III. Cooling fan speed changes.  Harness and connectors
 Cooling fan motor
 Cooling fan relay
 Cooling fan control module
 IPDM E/R
ALTERNATOR
DUTY Engine: Idle
 Change duty ratio using CON-
SULT-III. Battery voltage changes.  Harness and connectors
 IPDM E/R
Alternator
POWER BAL-
ANCE  Engine: After warming up, idle the
engine.
 A/C switch OFF
 Selector lever: P or N
 Cut off each injector signal one at a time using CONSULT-III. Engine runs rough or stops.
 Harness and connectors
 Compression
 Fuel injector
 Power transistor
Spark plug
 Ignition coil
IGNITION TIM-
ING  Engine: Return to the original
non-standard condition
 Timing light: Set
 Retard the ignition timing using
CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Perform Idle Air Volume Learning.
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (ECM)EC-71
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*: Leaving cooling fan OFF with CONSULT-III while engine is running may cause the engine to overheat.
DTC & SRT CONFIRMATION MODE
SRT STATUS Mode
For items whose SRT codes are set, “CMPLT” is disp
layed on the CONSULT-III screen; for items whose SRT
codes are not set, “INCMP” is displayed.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
DTC WORK SUPPORT Mode
*: DTC P1456 does not apply but appears in DTC Work Support Mode screens. V/T ASSIGN AN-
GLE
 Engine: Return to the original
non-standard condition
 Change intake valve timing using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Intake valve timing control sole-
noid valve
FPCM  Engine: Return to the original
trouble condition
 Select “LOW”, “MID” and “HI” with CONSULT-III. Fuel pump speed changes or stops.
 Harness and connectors
 Fuel pump control module (FPCM)
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
Test mode Test item Corresponding DTC No. Reference page
HO2S2 HO2S2 (B1) P1146 P0138
EC-249
HO2S2 (B1) P1147 P0137EC-243
HO2S2 (B1) P0139 P0139EC-257
HO2S2 (B2) P1166 P0158EC-249
HO2S2 (B2) P1167 P0157EC-243
HO2S2 (B2) P0159 P0159EC-257
A/F SEN1A/F SEN1 (B1) P1278/P1279 P0133
EC-238A/F SEN1 (B1) P1276 P0130EC-228
A/F SEN1 (B2) P1288/P1289 P0153EC-238
A/F SEN1 (B2) P1286 P0150EC-228
EVAPORATIVE SYSTEMEVP V/S LEAK P0456/P1456* P0456
EC-346, "
DTC Logic"
PURG VOL CN/V P1444 P0443EC-317, "DTC Logic"
PURG FLOW P0441 P0441EC-312, "DTC Logic"
Revision: 2010 May2011 QX56

EC-72
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000006217730
VALUES ON THE DIAGNOSIS TOOL
NOTE:
 Specification data are reference values.
 Specification data are output/input values which are
detected or supplied by the ECM at the connector.
* Specification data may not be directly relat ed to their components signals/values/operations.
i.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show
the specification data in spite of the ignition timing not being adjusted to the specification data. This IGN TIM-
ING monitors the data calculated by the ECM accordi ng to the signals input from the camshaft position sen-
sor and other ignition timing related sensors.
CONSULT-III MONITOR ITEM
Monitor Item Condition Values/Status
ENG SPEED  Run engine and compare CONSULT-III value with the tachometer indication. Almost the same speed as
the tachometer indication
MAS A/F SE-B1 See EC-161, "
Description".
B/FUEL SCHDL See EC-161, "
Description".
A/F ALPHA-B1 See EC-161, "
Description".
A/F ALPHA-B2 See EC-161, "
Description".
COOLAN TEMP/S  Ignition switch: ON Indicates engine coolant
temperature
A/F SEN1 (B1)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
A/F SEN1 (B2)  Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 1.5 V
HO2S2 (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
⇔ Approx. 0.6 - 1.0
V
HO2S2 MNTR (B1)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and
at idle for 1 minute under no load LEAN
⇔ RICH
HO2S2 MNTR (B2)  Revving engine from idle up to 3,000 rpm quickly after the following condi-
tions are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
⇔ RICH
VHCL SPEED SE  Turn drive wheels and compare CONSULT-III value with the speedometer in-
dication. Almost the same speed as
speedometer indication
BATTERY VOLT  Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1  Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.65 - 0.87 V
Accelerator pedal: Fully depressed 4.3 - 4.8 V
ACCEL SEN 2*
1 Ignition switch: ON (Engine stopped) Accelerator pedal: Fully released 0.56 - 0.96 V
Accelerator pedal: Fully depressed 4.0 - 4.8 V
Revision: 2010 May2011 QX56

ECM
EC-73
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
TP SEN 1-B1
 Ignition switch: ON
(Engine stopped)
 Selector lever: D position Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*
1 Ignition switch: ON (Engine stopped)
 Selector lever: D position Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE  Ignition switch: ON Indicates fuel tank tempera-
ture
EVAP SYS PRES  Ignition switch: ON Approx. 1.8 - 4.8 V
FUEL LEVEL SE  Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL  Ignition switch: ON → START → ON OFF → ON → OFF
CLSD THL POS  Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released ON
Accelerator pedal: Slightly depressed OFF
AIR COND SIG  Engine: After warming up, idle
the engine Air conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates.)
ON
PW/ST SIGNAL  Engine: After warming up, idle
the engine Steering wheel: Not being turned OFF
Steering wheel: Being turned ON
LOAD SIGNAL  Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting
switch: OFF OFF
IGNITION SW  Ignition switch: ON → OFF → ON ON → OFF → ON
HEATER FAN SW  Engine: After warming up, idle
the engine Heater fan switch: ON ON
Heater fan switch: OFF OFF
BRAKE SW  Ignition switch: ON Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
IGN TIMING  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 1 - 4
°BTDC
2,000 rpm 25 - 45 °BTDC
COMBUSTION — These items are displayed
but are not applicable to this
model.
CAL/LD VALUE  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 5 - 35%
2,500 rpm 5 - 35%
MASS AIRFLOW  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 2.0 - 6.0 g/s
2,500 rpm 7.0 - 20.0 g/s
PURG VOL C/V  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.)
0%
2,000 rpm 5%
INT/V SOL (B1)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle 0 - 2%
2,000 rpm Approx. 0 - 50%
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-75
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
BRAKE SW2
(Stop lamp switch)
 Ignition switch: ON Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
DIST SW  Ignition switch: ON DISTANCE switch: Pressed ON
DISTANCE switch: Released OFF
CRUISE LAMP  Ignition switch: ON MAIN switch: Pressed at the 1st time
→
at the 2nd time ON
→ OFF
AC EVA TEMP  Engine: Running Indicates A/C evaporator
temperature sent from“uni-
fied meter and A/C amp.”.
AC EVA TARGET  Engine: Running Indicates target A/C evapo-
rator temperature sentfrom
“unified meter and A/C
amp.”.
FAN DUTY  Engine: Running 0 - 100%
ALT DUTY  Engine: Idle 0 - 80%
BAT CUR SEN  Engine speed: Idle
 Battery: Fully charged*
2
 Selector lever: P or N position
 A/C switch: OFF
No load Approx. 2,600 - 3,500 mV
A/F ADJ-B1  Engine: Running −0.330 - 0.330
A/F ADJ-B2  Engine: Running −0.330 - 0.330
P/N POSI SW  Ignition switch: ON Selector lever: P or N ON
Selector lever: Except above position OFF
INT/A TEMP SE  Ignition switch: ON Indicates intake air temper-
ature
AC PRESS SEN  Engine: Idle
 Both A/C switch and blower fan switch: ON (Compressor operates) 1.0 - 4.0 V
FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 2.74 Mpa
2,000 rpm Approx. 3.0 Mpa
FUEL INJ B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
FUEL INJ B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.4 msec
2,000 rpm Approx. 1.0 msec
INT/V TIM (B1)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
INT/V TIM (B2)  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
−5 - 5 °CA
2,000 rpm Approx. 0 - 30 °CA
MAP SENSOR  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1.0 V
2,000 rpm Approx. 1.35 V
EVAP LEAK DIAG  Ignition switch: ON Indicates the condition of
EVAP leak diagnosis.
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

EC-76
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
EVAP DIAG READY  Ignition switch: ON Indicates the ready condi-
tion of EVAP leak diagnosis.
VVEL LEARN  Ignition switch: OFF
→ ON
(After warming up) VVEL learning has no
t been performed
yet. YET
VVEL learning has already been per-
formed successfully. DONE
VVEL SEN LEARN-B1  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL SEN LEARN-B2  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL POSITION SEN-
B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL POSITION SEN-
B2  Engine: After warming up
 Selector lever: P or N position
 Air conditioner switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL TIM-B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
VVEL TIM-B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
FPCM  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load  Engine: Cranking HI
 Revving engine from idle to 4,000 rpm
quickly MID
 Engine: Idle
 Engine coolant temperature: More than 10 °C (50 °F) LOW
BAT TEMP SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature
around the battery.
COOLING FAN SPD  Engine speed: Idle
 Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Water temp: Less than 98
°C Approx. 100 – 200 rpm
Water temp: More than 98 °C Approx. 600 – 700 rpm
THRTL STK CNT B1 NOTE:
The item is indicated, but not used. —
HO2 S2 DIAG2(B1) NOTE:
The item is indicated, but not used.
—
HO2 S2 DIAG2(B2) NOTE:
The item is indicated, but not used. —
FUEL INJ TIMG Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 16 deg
2,000 rpm Approx.
−170 deg
H/P FUEL PUMP DEG  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 211.0 deg
2,000 rpm Approx. 206.0 deg
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*1: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, the
y differ
from ECM terminals voltage signal.
*2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to PG-159, "
How to Handle Battery".
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
 Specification data are reference values and are measured between each terminals.
 Pulse signal is measured by CONSULT-III.
FUEL PRES SEN V Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 1150 mV
2,000 rpm Approx. 1200 mV
L/FUEL PRES SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.45 MPa
2,000 rpm Approx. 0.45 MPa
L/FUEL PRES SEN V  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 3250 mV
3,000 rpm Approx. 3100 mV
ECM TEMP 1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 1.
ECM TEMP 2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature of
ECM internal circuit 2.
FUEL PUMP DUTY  Engine: After warming up
 Shift lever: P or N
 Air conditioner switch: OFF
No load Engine speed: Idle 30 - 40%
Monitor Item Condition Values/Status
JPBIA3371ZZ
Revision: 2010 May2011 QX56

EC-78
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(R)
2
(R) 175
(B) Fuel injector No. 8 (HI)
Fuel injector No. 5 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
3
(G)
4
(G) 175
(B) Fuel injector No. 3 (LO)
Fuel injector No. 2 (LO)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
5
(B/R) — ECM ground — — —
JPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
Revision: 2010 May2011 QX56

ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
6
(R) 7
(R) 175
(B) Fuel injector No. 3 (HI)
Fuel injector No. 2 (HI)
Output[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
8
(G) 9
(G) 175
(B) Fuel injector No. 8 (LO)
Fuel injector No. 5 (LO)
Input[Engine is running]
 Warm-up condition
 Idle speed
NOTE:
The pulse cycle changes depending
on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm BATTERY VOLTAGE
(11 - 14 V)
10
(B) — ECM ground — — —
11
(BR) 175
(B) PNP switch Input [Ignition switch: ON]
 Selector lever: P or N position
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON]
 Selector lever: Except above posi- tion 0 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
OutputJPBIA3345ZZ
JPBIA3347ZZ
JPBIA3355ZZ
JPBIA3356ZZ
Revision: 2010 May2011 QX56

ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
23
(V) 45
(L/O) Low fuel pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
2.4 - 3.6 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 2.4 - 3.6 V
25
(LG) —Sensor ground
[Mass air flow sensor/ Intake air
temperature sensor] —— —
27
(P) 45
(L/O) Sensor power supply
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling)
— [Ignition switch: ON] 5 V
28
(SB) 40
(W/L) Sensor power supply
(Fuel rail pressure sensor/En-
gine oil pressure sensor)
— [Ignition switch: ON] 5 V
29
(W) 35
(—) Knock sensor (bank 1) Input [Engine is running]
 Idle speed
2.0 V*
1
31
(V/W) 40
(W/L) Fuel rail pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
0.98 - 1.2 V
[Engine is running]
 Warm-up condition
 Revving engine from idle to 4,000 rpm quickly 1.1 - 2.9 V
32
(R) 40
(W/L) Engine coolant temperature
sensor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
33
(W) 35
(—) Knock sensor (bank 2) Input [Engine is running]
 Idle speed
2.0 V*
1
35
(—) —Sensor ground
(Knock sensor)
—— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3357ZZ
JPBIA3358ZZ
Revision: 2010 May2011 QX56