Circuit ISUZU KB P190 2007 Workshop Repair Manual
Page 5069 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-131
CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (LHD) G.EXP Sheet 4/5
RTW 78AXF026301
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5070 of 6020
8A-132 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (LHD) G.EXP Sheet 5/5
RTW 78AXF026401
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5071 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-133
CIRCUIT DIAGRAM 4JJ1-TC (RHD) EXCEPT SOUTH AFRICA Sheet 1/5
RTW 78AXF030301
BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007
Page 5072 of 6020
8A-134 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM 4JJ1-TC (RHD) EXCEPT SOUTH AFRICA Sheet 2/5
RTW 78AXF030401
BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007
Page 5073 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-135
CIRCUIT DIAGRAM 4JJ1-TC (RHD) EXCEPT SOUTH AFRICA Sheet 3/5
RTW 78AXF030501
BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007
Page 5074 of 6020
8A-136 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM 4JJ1-TC (RHD) EXCEPT SOUTH AFRICA Sheet 4/5
RTW 78AXF030601
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5075 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-137
CIRCUIT DIAGRAM 4JJ1-TC (RHD) EXCEPT SOUTH AFRICA Sheet 5/5
RTW 78AXF030701
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5076 of 6020
8A-138 ELECTRICAL-BODY AND CHASSIS
CIRCUIT DIAGRAM 4JH1-TC (LHD) Sheet 1/2
RTW 78AXF004601
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5077 of 6020
ELECTRICAL-BODY AND CHASSIS 8A-139
CIRCUIT DIAGRAM 4JH1-TC (LHD) Sheet 2/2
RTW 78AXF004701
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007
Page 5078 of 6020
8A-140 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION
ECM (ENGINE CONTROL MODULE);
C24SE
Removal
1. Lift both the ECM harness connector locking levers and
remove the two harness connectors form the ECM.
2. Remove the four socket head screws securing the ECM to the mounting bracket.
3. Remove the ECM from the engine compartment .
4. Pull out the ECM.
5. Disconnect both red and tan connectors.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobilizer
programming (if equipped) is/are necessary”
Installation
Follow the removal procedure in the reverse order to install the
ECM.
Pay close attention to the important points mentioned in the
following paragraphs.
Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.
BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007