Circuit ISUZU KB P190 2007 Workshop Repair Manual

ELECTRICAL-BODY AND CHASSIS 8A-141
REMOVAL AND INSTALLATION

ECM (ENGINE CONTROL MODULE);
4JH1-TC


Removal
1. Remove the passenger side front seat – refer to Section 10
CAB.
2. Remove the passenger side front door opening scuff plate.
3. Raise the carpet to gain access to the four hex-head bolts securing the ECM and ECM cover to the floor pan .
4. Remove the four hex-head bolts.
5. Pull the two harness connector locks away from the harness connectors and then remove the connectors form
the ECM.
6. Remove the ECM from the vehicle.
Refer to the Section 6E-ENGINE of this Manual.
IMPORTANT: The replacement ECM must be programmed.
“SPS (Service Programming System) and immobilizer
programming (if equipped) is/are necessary”







Installation
Follow the removal procedure in the reverse order to install the
ECM.
Torque passenger seat securing bolts to the specified value –
refer to Section 10 CAB
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that ECM is securely connected.
This will prevent a poor contact and open circuit.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-142 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION



FUEL GAUGE UNIT AND SENDER
ASSEMBLY
Removal
1. Remove the fuel gauge unit and sender assembly.
Refer to the “ENGINE FUEL” Section 6C of this Manual.





Installation
To install the fuel gauge unit and sender assembly, follow the
removal procedure in reverse order.
Pay close attention to the important points mentioned in the
following paragraphs.



Rubber Seal
Be absolutely sure that the fuel sender rubber seals are
correctly seated.

Connector
Be absolutely sure that the fuel gauge unit connector is
securely connected.
This will prevent a poor contact and an open circuit.




BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-147

CIRCUIT DIAGRAM 4JA1T (L)
Sheet 1/2


RTW 78AXF008401

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-148 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JA1T (L)
Sheet 2/2





RTW 78AXF008501

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-151

CIRCUIT DIAGRAM C24SE (RHD)



RTW 780XF012201

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-152 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM C24SE (LHD) WITHOUT HEADLIGHTS LEVELING


RTW 680XF006701

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-153

CIRCUIT DIAGRAM C24SE (LHD) WITH HEADLIGHTS LEVELING


RTW 680XF006801

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-154 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM HFV6 (HALOGEN STD TYPE)





RTW 78AXF009401

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-155

CIRCUIT DIAGRAM HFV6 (HALOGEN PROJECTOR TYPE)





RTW 78AXF009501


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-156 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM HFV6 (CLEARANCE LIGHT, LICENSE PLATE LIGHT, TAIL LIGHT)


RTW 78AXF009601


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007