reverse ISUZU TF SERIES 2004 Repair Manual

ELECTRICAL-BODY AND CHASSIS 8A-305
REMOVAL AND INSTALLATION

This photo is based on 2 doors








DRIVER SEAT SIDE POWER WINDOW &
DOOR LOCK SWITCH
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.


DRIVER’S SIDE DOOR LOCK SWITCH
Removal
1. Door Lock ASM

Refer to the removal steps of the DOORS in section 10
“BODY”.
2. Door Lock Switch



Installation
To install, follow the removal steps in the reverse order.

8A-306 ELECTRICAL-BODY AND CHASSIS











FRT PASSENGER’S SIDE DOOR LOCK
ACTUATOR
Removal
1. Door Lock ASM

Refer to the removal steps of the DOORS in Section 10
“BODY”.
2. Door Lock Actuator

Remover the actuator fixing bolts.

Disconnect the door lock link rod.

Disconnect the actuator connector.

Installation
To install, follow the removal steps in the reverse order.










RR DOOR LOCK ACTUATOR-LH & RH
Removal
1. Door Lock ASM

Refer to the removal steps of the DOORS in section 10
“BODY”.
2. Door Lock Actuator

Remove the actuator fixing bolts.

Disconnect the door lock link rod.

Disconnect the actuator connector.

Installation
To install, follow the removal steps in the reverse order.

ELECTRICAL-BODY AND CHASSIS 8A-319
REMOVAL AND INSTALLATION

This photo is based on RHD





DRIVER SEAT SIDE POWER WINDOW &
DOOR LOCK SWITCH
(2 DOORS MODEL)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.

This photo is based on RHD






FRONT PASSENGER’S POWER WINDOW
& DOOR LOCK SWITCH
(2 DOORS MODEL)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.

8A-320 ELECTRICAL-BODY AND CHASSIS
This photo is based on RHD
DRIVER SEAT SIDE POWER WINDOW &
DOOR LOCK SWITCH
(4 DOORS MODEL)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.


Installation
To install, follow the removal steps in the reverse order.

This photo is based on RHD


FRONT PASSENGER’S POWER WINDOW
& DOOR LOCK SWITCH
(4 DOORS MODEL)
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.



Installation
To install, follow the removal steps in the reverse order.


REAR POWER WINDOW & DOOR LOCK
SWITCH-LH & RH
Removal
1. Disconnect the battery ground cable.
2. Removes the screw in pull cup with the tip of a screwdriver.
3. Remove the switch bezel by pushing the spring with the tip
of a screwdriver.
4. Disconnect the connector.

ATTENTION:
When removing a switch bezel lift from the front in the
bezel.
It follows the front with the screwdriver.
The clip has broken when lifting from the rear in the bezel.

ELECTRICAL-BODY AND CHASSIS 8A-321

Installation
To install, follow the removal steps in the reverse order.

8A-322 ELECTRICAL-BODY AND CHASSIS


DRIVER SEAT SIDE POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM

Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor

Loosen the fixing bolts to remove the power windo
w
motor from the regulator.



Installation
To install, follow the removal steps in the reverse order.



FRONT PASSENGER’S POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM

Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor

Loosen the fixing bolts to remove the power windo
w
motor from the regulator.



Installation
To install, follow the removal steps in the reverse order.




REAR POWER WINDOW MOTOR-LH &
RH
Removal and Installation
Refer to the “DRIVER SEAT SIDE POWER WINDOW
MOTOR” removal and installation steps in this section.

8A-336 ELECTRICAL-BODY AND CHASSIS
REMOVAL AND INSTALLATION



AUDIO
Refer to Section 9 “ACCESSORIES” for details.


CIGARETTE LIGHTER
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster ASM.
3. Remove the lighter

1.
4. Disconnect the connector

2.
5. Loosen the ring nut

3 at the back side.
6. Remove the outer case
4.
7. Remove the lighter holder
5 from the bezel.





Installation
Follow the removal procedure in the reverse order to install the
lighter.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the lighter connector is securely
connected.
This will prevent a poor contact and an open circuit.


ACC SOCKET
Removal
1. Disconnect the battery ground cable.
2. Remove the center cluster ASM.
3. Disconnect the connector.
4. Remove the holder nut
1.
5. Remove the ACC Socket
2

Installation
Follow the removal procedure in the reverse order to install the
lighter.

ELECTRICAL-BODY AND CHASSIS 8A-345
REMOVAL AND INSTALLATION



DOOR MIRROR CONTROL SWITCH
Removal
1. Disconnect the battery ground cable.
2. Door trim pad Assembly

Refer to section 10 “BODY” for door trim pad assembly
removal steps.
3. Door Mirror Control Switch
Remove the power window switch bezel.

Remove the screw.

Disconnect the switch connector.

To remove the switch panel assembly.



Installation
To install, follow the removal steps in the reverse order.




DOOR MIRROR
Removal and Installation
Refer to the DOOR MIRROR in section 10 “BODY”.

ELECTRICAL-BODY AND CHASSIS 8A-355
REMOVAL AND INSTALLATION

865R300008


REAR DEFOGGER SWITCH
Removal
1. Instrument Panel Cluster Assembly

Refer to Section 10 “BODY” for center cluster panel
assembly removal steps.
2. Rear Defogger Switch (With HVAC control unit)
Refer to Section 1 “HVAC” HVAC control unit assembly
removal steps.



Installation
Follow the removal procedure in the reverse order to install the
rear defogger switch.

8A-372 ELECTRICAL-BODY AND CHASSIS
2WD-4WD Switch
REMOVAL AND INSTALLATION
825R300018

Removal
1. Remove the center cluster ASM
2. Disconnect the connector.
3. Remove the 2WD-4WD switch.


Installation
To install, follow the removal steps in the reverse order.