Heel board JAGUAR X308 1998 2.G Owner's Guide

Seating - Rear Seat Backrest Cover
Removal and Installation
Removal
1. Remove rear heel boards.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Remove rear seat belt ecutcheon. Refer to 76.73.18.
4. Remove rear seat squa b. Refer to 76.70.38.
5. Place seat squab inverted on clean work surface.

6. Withdraw clips from headrest supports and remove headrests
from seat squab.

7. Remove the six clips securing re ar seat armrest aperture cover
to frame and position cover for access.

8. Slacken and remove the two sq uab mounting bracket screws
and remove brackets from frame.

9. Remove and discard the three ho g rings securing armrest rear
cover retaining strip, release strip from frame and remove arm
rest.

17. Fit rear seat squab . Refer to 76.70.38.
18. Fit rear seat belt escutc heons. Refer to 76.73.18.
19. Fit rear seat cushion. Refer to 76.70.37.
20. Fit rear heel boards.

Seating - Rear Seat Cushion Removal and Installation
Removal
Installation

1.
Heated rear seat only. Remove battery cover and disconnect ground
cable from battery terminal. Refer to 86.15.19.

2. Slacken, remove and discard 1/4 turn fastener securing each
heelboard trim panel and withdraw both panels for access.

3. Slacken and remove the seat cushion securing screws.

4. Raise rear of cushion, disconnect heater element harness multiplugs
(if fitted), and move cushion forw ard carefully feeding seat belt
buckles past cushion cut-outs.
5. Remove seat cushion from vehicle.
1. Holding outer seat belts clear, posi tion cushion in vehicle with rear
edge raised.
2. Position buckle assemblies and carefully feed them past cut-outs in
cushion.
3. Heated seat only. Connect heat er element harness multiplugs.
4. Fit and fully tighten cushion front securing screws.
5. Using new 1/4 turn fasteners, fi t and secure heelboard trims.
6. Reposition seatbelts.
7. Heated seat only. Fit ground cable to battery terminal and fit battery
cover. Refer to 86.15.15.

Seating - Rear Seat Cushion Cover
Removal and Installation
Removal
1. Remove rear heel boards.
2. Remove rear seat cushion. Refer to 76.70.37.
3. Place seat cushion inverted on clean work surface.

4. Remove and discard the eight hog rings securing cover at each
seat belt anchor aperture.

5. Remove and discard hog rings se curing outer edges of cover
and cushion to frame.

6. Remove and discard two hog ri ngs securing centre panel
overlap plastic edge fastener and release fastener from frame.

7. Withdraw centre overlap thro ugh cushion for access.and
remove and discard hog rings secu ring horizontal seam of right
hand panel to cushion.

14.
Fit rear seat cushion to ve hicle. Refer to 76.70.37.
15. Fit rear heel boards.

Seating - Rear Seat Head Restraint
Removal and Installation
Removal
Installation

1.
Remove rear heel boards.
2. Remove rear seat cushion.
3. Remove rear seat belt escu tcheon. Refer to 76.73.18.
4. Fully lower headrests.
5. Remove rear seat squa b. Refer to 76.70.38.

6. Place seat squab inverted on clean work surface and remove
headrest retaining clips.
7. Withdraw headrest from seat squab.
1. Position headrest fully lowered on seat squab.
2. Fit and fully seat headrest retaining clips.
3. Fit rear seat squab asse mbly. Refer to 76.70.38.
4. Fit rear seat belt escutc heons. Refer to 76.73.18.
5. Fit rear seat cushion. refer to 76.70.37.
6. Fit rear heel boards.
7. Raise headrests to original positions.