cooling JAGUAR X308 1998 2.G Workshop Manual

                              
                                                                                   Valve
 Co
ver 
LH (12.29.43)  
                     Valve
 Cover  RH (12.29.44)  
                     Valve
 Cover  Gasket  LH  (12.29.40)  
                     Valve
 Cover Gasket  RH  (12.29.41)  
                     Valve
 Springs  LH 
                     Valve
 Springs  RH 
                     Variable
 Camshaft  Timing  Oil  Con
trol Unit  LH  (12.65.71)  
                     Variable
 Camshaft  Timing  Oil  Control  Unit  RH  (12.65.70)  
                     Variable
 Camshaft  Timing  Oil  Control  Unit  Housing  LH  (12.65.52)  
                     Variable
 Camshaft  Timing  Oil  Control  Unit  Housing  RH  (12.65.51)  
 
             303‐03A : Engine  Cooling  
                 Descriptio
n and  Operation  
                     Engine Cooling  
                 Diagnosis  and  Testing  
                     Engine Cooling  
                     Related Faults  /  Codes  
                     DTC P0116  ECT  circuit  range  / performance  problem 
                     DTC P0125  Insufficient  coolant  temperature  for  closed  loop  fuel control  
                     DTC P0117  ECT  circuit  low  input  
                     DTC P0118  ECT  circuit  high  input  
                     DTC P1474  Intercooler  coolant  pum
p relay  malfunction  
                     Pinpoint test  A: P0116,  P0125  
                     Pinpoint test  B: P0117  
                     Pinpoint test  C: P0118  
                     Pinpoint test  D: P1474  
                 General Procedures  
                     Cooling System  Draining,  Filling and  Bleeding  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  –  
            AJ27 
                     Cooling System  Draining,  Filling and  Bleeding  ‐ 4.0L  SC  V8  ‐ AJ26  
                     Cooling Sy
stem  Draining  and  Vacuum  Filling  
                 Removal and  Installation  
 
Removal
 
Engine  ‐ Re m
oval
 (12.41.01)  
Installation  
Engine  ‐ Installation  (12.41.01)  

                    Coolant E x
pansion
 Tank  (26.15.01)  
                    
Coolant Outlet  Pipe  (26.31.08)  
                    
                     Cooling Fan  Motor  (26.25.24)  
                     Cooling Fan  Motor  and  Shroud  (26.25.25)  
                     Cooling Fan  Motors  (26.25.25)  
                     Cooling Fan  Shroud  (26.25.30)  
                     Engine Coolant  Level  Switch  (26.40.11)  
                     Radiator (26.40.01)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Radiator (26.40.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Radiator Lower Hose  (26.30.07)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Radiator Lower Hose  (26.30.07)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Radiator Upper Ho
se (26.30.01)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Radiator Upper Hose  (26.30.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  (26.45.07)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Thermostat  (26.45.07)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  Housing  Cover  (26.
45.22)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Thermostat  Housing  Cover  (26.45.22)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Thermostat  Housing  Cover  Seal  (26.45.20)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Thermostat  Housing  Cover  Seal  (26.45.20)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Water Pump  (26.50.
01) ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                     Water Pump  (26.50.01)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Water Pump  Pulley  (26.50.05)  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ27  
                     Water Pump  Pulley  (26.50.05)  ‐ 4.0L  SC  V8 ‐ AJ26  
 
             303‐03B : Supercharger  Cooling 
                 Removal and  Installation  
                     Water Pump  
 
             303‐04:  Fu
el Charging  and Controls  
                 Diagnosis  and  Testing  
                     Fuel Charging  and Controls  
                 Inspection  and Verification  
                     Driver Information  Chart  
                     Default mode Definitions  
                     Diagnostic Trouble  Code  (DTC)  index  
                     Pinpoint Tests  

 
            307‐01B : A u
tomatic
 Transmission/Transaxle  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Vehicle  Repair  
                     Extension Housing  Seal  (44.20.18)  
                     Main Control  Valve Body  (44.40.01)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Support Insulator  (12.45.04)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Shaft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
 
             307‐02A : Transmission/Transaxle  Cooling  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ
27  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐02B : Transmission/Transaxle  Cooling  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐05A : Automatic  Transmission/Transaxle  External  Controls  ‐ 3.2L  NA  V8  –  
            AJ26/4.0L NA  V8  ‐ AJ27  
                 Description  and  Operation  
                     External Controls  

Electrically Programmable
R
ead-Only memory
EPROM
Ele
c
tronic Secondary Air
Injection
EAIRA p
ump-driven system for providing seco
ndary air using an electric air pump
Engine C
ontrol Module
ECM
End of dashEODR
e
ferring to a vehicle fascia, eg EOD air vent
Engine
C
oolant Level
ECL
Engine
C
oolant
Temperature
ECT
ECT Sen s
or
ECTSTherm
i
stor which provides engine coolant temperature signal to the ECM to
trigger enrichment circuits which increase injector 'on' time for cold start and
warm-up
Engine s
peed
RP
M
Environ m
ental Protection
Agency
EPA
Evaporative EmissionEVAPSy stem designed to prevent fu
el vapor from escaping into the atmosphere.
Typically includes a charcoal filled canister to absorb fuel vapor
Evaporative Emission
Control ValveEVAPP
Exhaust G
as Recirculation
EGRSys
t
em which reduces NOx emissions by adding exhaust gases to the
incoming fuel/air charge
Exhaus t G
as Recirculation

Solenoid Vacuum Valve
EGRS
Exhaus t G
as Recirculation

Temperature Sensor
EGRT Sen s
or
Exhaus
t G
as Recirculation

Valve
EGRV
F
F a
n Control
FCEngine

cooling fan control
F
e
deral Motor Vehicle
Safety Standard (US)
FMV S
S
Fi
gur
e
Fi
g.Illustrati
on reference
Flash
E
lectrically Erasable

Programmable Read-Only
Memory
FEE PR
OM
Flash
E
rasable
Programmable Read-Only
Memory
FEP R
OM
Flywhee
l
Sensor
CKFSSens
or moun
ted so as to be
triggered by each flywheel ring gear tooth to give
an engine speed signal
Fue l
Injectors
FISol
e
noid operated devices that spray a metered quantity of fuel into the inlet
ports
F u
el Pressure Regulator
Control
FP RCControls fuel pressure regu l
ator; used primarily to
give extra fuel at cold
start-up
Fue l
Pump
FP
Fue
l
Pump Monitor
FP
MMonitors operation of fuel pump
Fue l
Pump Relay
FP
R
Fu
el rich/lean
Q
u
alitative evaluation
of air/fuel ratio based on a ratio known as
stoichiometry, or 14.7:1 (Lambda)
F u
ll Scale Deflection
FSDTh
e
maximum indication point on
an analogue meter or gauge
G
Gene
rator
GENRot
a
ting machine which converts mechanical energy into electrical energy
G
r
amme centimeter
gcm
Gramm
e
(force)
gf
Gramm
e
(mass)
g
GroundGNDEle
c
trical conductor used
as a common return for an electrical circuit or
circuits, and with a relative zero potential
H
Hard f a
ult
A
fau
lt currently present in the system
HeadlampHL
Heat
ed Oxygen
Sensor
HO2SElectrically
h
eated oxygen sensor which induces fueling corrections
Hertz (frequency)HzFrequ
e
ncy, one cycle per second
High
Moun
ted Stoplamp
HMSL

Front Suspension -
Lubri
cants, Fluids, Sealants and Adhesives
Press-In Loads
Torques


UnitS
pecification
Loctite27

0
Greas

e
Shell Retin
ax 'A'
Greas

e
Castro
l 'NTR'
Com

ponent
Kn
Ball join

t to upper wishbone
25
- 50
B

all joint to lower wishbone
25
- 50
Com

ponent
Nm
N

ut - ball joint, upper wishbone to vertical link.
60
-80
N

ut - ball joint, lower wishbone to vertical link.
60
-80
Nu

t - fulcrum bolt, upper wishbone.
60
-80
N

ut - ball joint, tie rod to steering arm.
71
-85
Bol

t - wheel speed sensor to vertical link.
8-1
0
Bol

t - front mounting to crossbeam.
22
-28
Bolt

- mounting , stabilizer bar.
30
-40
N

ut - link arm ball joint to stabilizer bar.
60
-80
Bolt

- mounting, steering rack to crossbeam.
41
-54
B

olt - front mounting, crossbeam to body.
22
-28
Bol

t - spring pan to lower wishbone.
70
-90
N

ut - shock absorber to upper mounting
(vehicles with adaptive damping).
16
-18
Nu

t - shock absorber to upper mounting (vehicles without adaptive damping).
30
-40
N

ut - shock absorber lower to wishbone.
43
-57
B

olt - engine Hydramount to crossbeam.
34
-46
B

olt - crossbeam rear mounting to body.
13
1-185
Bol

t - generator cooling du
ct deflector to crossbeam.
17
-23
N

ut - lower steering column to pinion shaft.
22
-28
N

ut - hub, speed sensor rotor.
27
0-330
B

olt - shield, brake disc.
9-1
2
Bol

t - lower wishbone, front arm to rear arm.
77
-103
Nu

t - stabilizer bar link arm to wishbone bracket.
41
-54
N

ut - wishbone front
eccentric bolt.
11
3-153
Nu

t - wishbone rear
eccentric bolt.
11
3-153
N

ut - fulcrum shaft, upper wishbone.
60
-80
Bolt -

power steering pi
pes to pinion housing.
9-1
2

Front Suspension - Fro
nt Stabilizer Bar
Re
moval and Installation
Materials
S
pecification
Cas

trol NTR
Remov

al
Na
me
R

ubber Suspension Insulator Lube
1. Raise front of vehicle and support on stands. Refer to Section
100-02.

2. R
emove generator front cooling duct.
Re

move bolt.
Move duct rea

rwards to rele
ase tang from undertray.
R
elease front duct from rear vertical duct.

3. R
emove scrivets or screws se
curing undertray to bumper
cover. Discard scrivets.

4. R
emove and discard tiestrap securing undertray to crossbeam
brace.
5. At each side of vehicle, remo ve and discard scrivet securing
undertray to wheelarch liner.

Front Suspension - Front Stabilizer B
ar Bushing
Re
mo
val and Installation
Materials
S p
ecification
Cas
t
rol NTR
Remov
a
l
Na
m
e
R
u
bber Suspension Insulator Lube
1. Raise front of vehicle and support on stands. Refer to Section
100-02.

2. Re
move generator front cooling duct.
Re
mo
ve bolt.
Move duct rea
r
wards to rele
ase tang from undertray.
Re
lease front duct from rear vertical duct.

3. Re
move scrivets or screws se
curing undertray to bumper
cover. Discard scrivets.

4. Re
move and discard tiestrap securing undertray to crossbeam
front brace.
5. At each side of vehicle, remo ve and discard scrivet securing
undertray to wheelarch liner.

Front Disc Brake - Front Disc Brake
Description and Operation


The brake disc is mounted on the wheel studs and is clamped between the wheel and hub. Cooling ducts run through the
center of the brake disc to provide the required ventilation to keep the disc cool under operating conditions.
The caliper carrier, which is se cured to the vertical link by two bolts, carries the single-pis ton caliper housing. The caliper
housing is secured to the caliper carrier by two guide-pins and an anti-rattle spring. When the brakes are applied the
caliper-housing piston pushes th e brake pad in front of it, towards the brake di sc. This movement forces the caliper housing
to move along the guide-pins, in the oppo site direction of the piston, to apply the second brake pad. The brake disc is
therefore gripped between the two pads. As brake pressure is increased the grip on the brake disc is increased to slow-down
the rotation of the road wheel.
The disc brakes requ ire no adjustment.
It
e
m
Par
t
Number
De
scr
iption
1—B
r
ake Disc
2—Caliper Housin
g
3—Caliper Carrier
4—Brake Pads
5—Guide P i
ns
6—Du
st
Covers
7—An
ti
-rattle Spring
8—Du
st
Shield
9—Brake Hos
e

10—Bleed Nipp
le

• C
AUTIONS:
The Brembo caliper is aligned to the brak e disc when it is first installed to the vehicle, therefore, care must be taken
not to disturb this alignment. When removi ng the caliper; remove the bolts that secure the anchor bracket to the vertical
link only. DO NOT loosen any other caliper bolts.
Do not loosen bolts securing brake disc to disc mounting.
Brembo calipers and discs provide higher -performance braking using the existing hydraulic braking system. The brakes are
installed to the vehicle using unique vertical links, hubs, hydraulic hoses and disc shields.
The front brake disc consists of a ventilated, cross-drilled disc, bolted to a disc carrier. The disc assemb ly is mounted on the
wheel studs and clamped be tween the wheel and hub.
A unique feature of the front disc is th e slanted (non radial) ventilation webs which lean the opposite-way to the disc's
direction of rotation. This design enables he at generated by the disc to be dispersed by air entering at the disc's center and
being forced outwards through the cooling ducts.
Due to the use of fixed calipers in place of the standard floating caliper, certain lateral dimensions on the vertical link and
It
em
Par
t Number
De
scription
1—B

rake Disc
2—Caliper


3—Anch

or Bracket
4—Anchor Pl

ate to Vertical Link - Bolts
5—Brake Pad

s
6—Guide P

ins
7—Anti-r

attle Spring
8—Di

sc Shield
9—Brake Hos

e
10—Bleed Nipp

les


Front Disc Brake—
Brembo

Rear
Disc Brake - Rear Disc Brake
Description an
d Operation

The brake disc is mounted on the wheel studs and is clamped between the wheel and hub. Cooling ducts run through the
center of the brake disc to provide the required ventilation to keep the disc cool under operating conditions.
The caliper carrier, which is se cured to the hub carrier by two bolts, carries the single-piston caliper housing. The caliper
housing is secured to the caliper carrier by two guide-pins and an anti-rattle spring. When the brakes are applied the
caliper-housing piston pushes th e brake pad in front of it, towards the brake di sc. This movement forces the caliper housing
to move along the guide-pins, in the oppo site direction of the piston, to apply the second brake pad. The brake disc is
therefore gripped between the two pads. As brake pressure is increased the grip on the brake disc is increased to slow-down
the rotation of the road wheel.
The disc brakes requ ire no adjustment.
It
em
Par
t Number
De
scription
1—B

rake Disc
2—Caliper Housin

g
3—Caliper Carrier
4—Brake Pad

s
5—Guide P

ins

6—Du
st Covers
7—An

ti-rattle Spring
8—Du

st Shield
9—Brake Hos

e
10—Bleed Nipp

le