ECU JAGUAR X308 1998 2.G Workshop Manual

Interior Trim and Ornamentation - Rear Door Window Control Switch
Finish Panel
Removal and Installation
Removal
Installation

1.
Remove door casing veneer panel. Refer to 76.47.12.
2. Remove door casing. Refer to 76.34.04.
3. Remove door armrest and remo ve switch/ashtray assembly
from armrest. Refer to 76.34.23.

4. Slacken and remove screws securing veneer panels to door
glass switch/ashtray assembly.
5. Remove veneer panels from switch/ashtray assembly.
1. Position veneer panel over switch/ashtray assembly and fit and
tighten securing screws.
2. Position switch/ashtray assembly on armrest and fit and
tighten the two securing screws.
3. Fit armrest to door casing. Refer to 76.34.23.
4. Fit casing to door. Refer to 76.34.04.

Interior Trim and Ornamentation - Scuff Plate Trim Panel
Removal and Installation
Removal
Installation



1. NOTE: The finisher can be easily damaged, care must therefore be exercised during removal.
Using a thin plastic lever and starting at one end, carefully
remove the treadplate finisher and place face uppermost on
sheet of clean dry polythene.

2. Remove treadplate securing sc rews and remove treadplate.
1. Ensure that draught welt is correctly positioned and fully
seated on aperture flange.
2. Position sill tread plate and install three securing screws.
3. Ensure that sill contact area is clean and dry.
4. Install treadplate finisher, pressing firmly into place. If finisher
has been renewe d, remove protective film.

Interior Trim and Ornamentation - Sun Visor
Removal and Installation
Removal
Installation

1.
Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Release sun visor from suppo rt and turn downwards.

3. Supporting the sun visor, sl acken and remove the three
screws securing the mounting to the header.

4. Disconnect the harness multiplug situated behind the
headlining and remove the sun visor.
5. Slacken and remove screw securing sunvisor support, and
remove support from header.
1. Position sun visor at header.
2. Connect multiplug and position it behind headlining.
3. Correctly position and firmly seat sun visor mounting on
header and fit and tighten securing screws.
4. Position sun visor support at header and fit and tighten
securing screw.
5. Connect ground cable to battery terminal and fit battery cover.
Refer to 86.15.15.

Exterior Trim and Ornamentation - Luggage Comp artment Lid Moulding
Removal and Installation
Removal
1. Remove battery cover and disc onnect ground cable from
battery terminal. Refer to 86.15.19.
2. Disconnect and remove trunk lamp assemblies. Refer to
86.45.16.

3. Remove covers from trunk latc h finisher securing bolts,
slacken and remove bolts and remove finisher.

4. Remove and discard trunk li d liner rear fasteners and
position liner for access.

5. Free trunk lid release button harness from retaining clip and
disconnect multiplug.
6. NOTE: The pressed steel fasteners fitted to Jaguar models
should be discarded on removal.
Slacken and remove nuts/fasteners securing trim finisher to
trunk lid.

Installation


7. Position trim finisher for a ccess and withdraw and discard
release button harness grommet from trunk lid.
8. Remove trim finisher from trunk lid.

9. Carefully remove seal from trim finisher.

10. Slacken and remove screws securing release button assembly
to trim finisher and remove release button from finisher.
1. Fit and fully seat release button in trim finisher and fit and
tighten securing screws.
2. Apply suitable adhesive to contac t area of trim finisher and fit
and align seal to finisher.
3. Position trim finisher and pass release button harness through
trunk lid aperture.

4.
Fit and fully seat a new harn ess grommet in trunk lid.
5. NOTE: Fit new pressed steel fasteners on Jaguar models.
Align and fully seat trim finisher on trunk lid and fit and fully
tighten securing nuts/fasteners.
6. Connect release button harness multiplug and position harness
in retaining clip.
7. Position and fully seat trunk li d trim pad and secure with new
fir tree fasteners.
8. Fit finisher over trunk latch, fi t and tighten securing bolts and
fit bolt covers..
9. Fit trunk lamp assemblies. Refer to 86.45.16.
10. Connect ground cable to batt ery terminal and fit battery
cover. Refer to 86.15.15.

Exterior Trim and Ornamentation - Radiator Grille
Removal and Installation
Removal
Installation



1. Slacken and remove the two scre ws securing top of grill to
surround.

2. Lift grill to withdraw retainin g lugs from slots and remove
grill from vehicle.
3. Remove and discard the two ny lon screw inserts from top of
surround (adapters for su percharged models).
4. Repeat above steps to remove grill on opposite side.
1. Fit new screw inserts/adapters to top of grill surround.
2. Fit grill lower lugs into suurround slots.
3. Fit and tighten the two screws securing top of grill to surround.

4. Repeat above steps to instal l grill on opposite side.

Exterior Trim and Ornamentation - Radiator Grille Bezel
Removal and Installation
Removal
Installation

1.
Remove radiator grills for access. Refer to 76.55.03.

2. Slacken and remove the two screws securing each end of
surround to BIW and remove surround from vehicle.
3. Remove and discard the two nylon screw inserts from each
side of BIW.
1. Fit new screw inserts to BIW locations.
2. Position grill surround on BIW and fit and tighten securing
screws.
3. Fit radiator grills. Refer to 76.55.03.

Rear View Mirrors - Auto-Dimming Interior Mirror
Removal and Installation
Removal
Installation

1.
Remove roof console for access and disconnect interior mirror
harness multiplugs. Refer to 76.13.69.90.

2. Remove upper cover from mirror stem.
3. Remove rain sensor unit. Refer to Section 501.16.

4. CAUTION: When removing mirror from base, care must
be exercised to ensure that base is not detached from windshield.
Applying firm downward pre ssure, remove mirror assembly
from base.
1. Position mirror at bottom of base and apply firm upward
pressure to fully seat and secure in position.
2. Install upper cover to mirror stem.
3. Position roof console at head er and connect mirror harness
multiplugs.
4. Install rain sensor unit. Refer to Section 501.16.
5. Install roof console. Refer to 76.13.69.

Rear View Mirrors - Exterior Mirror
Removal and Installation
Removal
Installation

1.
Fully open door glass and ease top of door casing away from
door Refer to 76.34.01.
2. Remove door frame cheater trim and memory foam for access.

3. Remove mirror assembly from door.
1. Disconnect mirror harness multiplug.
2. Supporting mirror, slacken and remove securing screw and remove mirror assembly from door.

1. Fit exterior mirror assembly to door.
1. Pass harness and multiplu g through cheater aperture
and position mirror foot on cheater, locating the two
dowels correctly and ensuring correct seating on seal.

Fit and tighten the mirror assembly securing screw.
Connect mirror assembly harness multiplug, position in
door and reposition door foam.
2. Fit memory foam and door frame cheater trim.
3. Close door glass.
4. Fit top of door casing. Refer to 76.34.01.