flex plate JAGUAR X308 1998 2.G Workshop Manual

                    
                                                                                                      Flexplate
 Vehicles  With
out: 
Supercharger  (12.53.13) 
                     Flexplate
 Vehicles  With: Supercharger  (12.53.13)  
                     Intake
 Camshaft  LH  (12.13.16)  
                     Intake
 Camshaft  RH  (12.13.14)  
                     Intake
 Manifo
ld (30.15.01)  
                     Intake
 Manifold  Gaskets  (30.15.08)  
                     Intake
 Manifold  LH  (18.50.26)  
                     Intake
 Manifold  RH  (18.50.25)  
                     Intake
 Manifold  Gasket  LH  (18.50.28)  
                     Intake
 Manifold  Gasket  RH  (18.50.27)  
                     Oil
 Pan  (12.60.44)  
                     Oil
 Pan  Gasket  (12.60.38)  
                     Oil
 Pressure  Switch (88.25.07)  
                     Oil
 Pump  Vehicles  Without:  Supercharger  (12.60.26) 
                     Oil
 Pump  Vehicles  With: Supercharger  (12.60.26)  
                     Primary
 Timing  Chain  LH  4.0L,  Vehicles  Wit
hout:  Supercharger  (12.65.67) 
                     Primary
 Timing  Chain  LH  3.2L/4.0L,  Vehicles With:  Supercharger  (12.65.67)  
                     Primary
 Timing  Chain  RH  (12.65.66)  
                     Primary
 Timing  Chain  Inner  Guide  LH  (12.65.58)  
                     Primary
 Timing  Chain  Inner  Guide  RH  (12.65.60)  
                     Primary
 Timing  Chain  Outer  Guide  LH  (12.65.61)  
                     Primary
 Timing Chain  Outer  Gu
ide  RH  (12.65.57)  
                     Primary
 Timing  Chain  Tensioner  LH  (12.65.55)  
                     Primary
 Timing  Chain  Tensioner  RH  (12.65.54)  
                     Secondary
 Timing  Chain  LH  (12.65.69)  
                     Secondary
 Timing  Chain  RH  (12.65.68)  
                     Secondary
 Timing  Chain  Tensioner  LH  4.0L,  Vehicles  Without:  Supercharger   
           (12.65.64)
 
                     Secondary
 Timing  Chain  Tensioner  LH  3.2L/4.0L,  Vehicles  With: Supercharger  
           (12.65.64)
 
                     Secondar
y Timing  Chain  Tensioner  RH  4.0L,  Vehicles  Without:  Supercharger   
           (12.65.63)
 
                
                                                        
Secondar y Timing  Ch
ain
 Tensioner  RH  3.2L/4.0L,  Vehicles  With: Supercharger  
(12.65.63)  
Upper  Oil  Pan  3.2L  (12.60.48)  
Upper  Oil  Pan  4.0L,  Vehicles  Without:  Supercharger  (12.60.48) 
Upper  Oil  Pan  4.0L,  Vehicles  With: Supercharger  (12.60.48)  

Re
ar Drive Axle/Differential -
Lubric
ants, Fluids, Sealants and Adhesives
Capacities
Torques


UnitSp
ecification
F
i
nal Drive
Shell Sp
irax Supe
r TS 90
Hub s
p
line to Axle shaft
Loct
it
e 270 Studlock or equivalent
UnitLi
t
ers
F
i
nal Drive
1,
90
Com p
onent
Nm
B
ol
t - Final drive nose plate
39
- 51
Bol t
- 'A' frame to final drive
9
0 -
110
Nu
t 'A' f
rame to rear mounting bracket
8
5 -
115
Nu
t -
Axle shaft to final drive flange
81
-
99
Nu
t -
Axle shaft to hub
3
04 -
336
N
u
t - Damper lower fixing
8
0 -
100
Bol
t
M12 - Jurid flexible coupling to
transmission and final drive flanges
75 -
88
N
u
t - Lower fulcrum
9
0 -
110
Nu
t -
Pendulum to final drive
1
60 -
200
N
u
t - Stabilizer to wishbone
30
-
40
N
u
t - Tie rod to final drive
8
5 -
105
Nu
t -
Tie rod to wide mounting bracket
8
5 -
115
Nu
t -
Wishbone pivot
8
0 -
100
N
u
t - Wishbone tie to final drive
8
5 -
105
N
u
t 'A' frame to wide mounting bracket
8
5 -
105

Engine - Flexplate4.0L NA V8 - AJ27/3.2L NA V8 - AJ26
In-vehicle Repair
Removal
Installation
1. Open the engine compartment and fit paint protection sheets.

2. Disconnect the batt ery ground cable.
Remove the battery cover.
3. Remove the Engine Covers, Air Intake Tube, Catalytic
Converters and the Front Muffler. Drain the transmission fluid
and remove the transmission for access.
Refer to Operation 44.20. 01 Transmission Remove, in
Section 307-01A, which includes each of the above
operations.

4. Remove the drive plate.
Prevent the drive plate from rotating by use of a small
wedge in the ring gear.
Remove the bolts which secure the drive plate to the
crankshaft.
Remove the drive plate.
5. Clean the crankshaft mating face and any other components
which are to be refitted.

1. Fit the drive plate.
Fit and align the drive plate to the crankshaft.
Fit, but not tighten, the bolt s which secure the drive plate
to the crankshaft.
Prevent the drive plate from rotating by use of a small
wedge in the ring gear.
2. Tighten the securing bolts in two stages and in the order
shown.

Engine - Flexplate4.0L SC V8 - AJ26
In-vehicle Repair
Removal
Installation
1. Open the engine compartment and fit paint protection sheets.

2. Disconnect the batt ery ground cable.
Remove the battery cover.
3. Remove the Engine Covers, Air Intake Tube, Catalytic
Converters and the Front Muffler. Drain the transmission fluid
and remove the transmission for access.
Refer to Operation 44.20. 01 Transmission Remove, in
Section 307-01B, which includes each of the above
operations.

4. Remove the drive plate.
Prevent the drive plate from rotating by use of a small
wedge in the ring gear.
Remove the bolts which secure the drive plate to the
crankshaft.
Remove the drive plate.
5. Clean the crankshaft mating face and any other components
which are to be refitted.

1. Fit the drive plate.
Fit and align the drive plate to the crankshaft.
Fit, but not tighten, the bolt s which secure the drive plate
to the crankshaft.
Prevent the drive plate from rotating by use of a small
wedge in the ring gear.
2. Tighten the securing bolts in two stages and in the order
shown.