ECU JEEP CJ 1953 User Guide

D
HURRICANE
F4
ENGINE d.
Remove the intake valve adjusting screw lock-
nuts from each of the rocker arm valve lash ad­

justing
screws. Remove the screws from the rocker
arms.

D-76.
Inspection and
Repair

Run
a round wire brush through the bore of the

rocker
arm shaft and clean out the drilled oil holes.
Clean
out the oil
holes
in the rocker arm shaft

brackets,
and the oil
holes
and
grooves
in the bores
of the rocker arm.
Inspect
the diameter of the shaft at the rocker arm

bearing
areas. Replace the shaft if there are scores

or
abrasion marks along the length of the shaft.
Check
the shaft for alignment by rolling it across

a
smooth level surface. If the shaft
will
not
roll
freely, or if it rolls with a bumping motion, the
shaft is out of alignment and must be replaced.
Inspect
the threads of the adjusting screw
hole
in
the rocker arms and if necessary clean with a

proper
size tap. Replace the adjusting screw lock-
nut or the adjusting screw if either part is damaged

or
deformed.

Inspect
the threads in the tapped
hole
in the top
of the rocker arm shaft brackets and if necessary

clean
with a proper size tap. Replace the bracket

if
either side is worn or scored.

D-77.
Reassembly

a.
Install
two rocker arm shaft plugs, one in each
end of the shaft. Slide two
rocker
arm
shaft brackets
onto
the center of the shaft. Align the tapped
holes

in
the brackets with the drilled
holes
in the top of
the shaft and install the rocker arm shaft lock
screws,
making sure the points of the screws enter
the drilled
holes
in the shaft.

b.
Screw the intake valve adjusting screws into
the rocker arms and install the locknuts.

c.
The rocker arms are paired; that is, two of the
arms
are angled to the right and two are angled to
the left. One of each type is used on each end of
the rocker arm shaft. Slide a rocker arm with the

adjusting
screw end of the rocker arm angling

away
from the bracket
onto
the shaft so that the
adjusting
screw is on the same side of the shaft
as the mounting
hole
in the bracket.

d.
Temporarily
secure the end bracket in place by
installing
a rocker arm cover stud in the tapped
opening in the top of the support.
e. Assemble the parts on the
opposite
end of the
rocker
arm shaft repeating
steps
c and d above.

D-78. ENGINE REASSEMBLY
The
engine
reassembly procedure in the following

paragraphs
is given in the sequence to be followed
when the
engine
is being completely overhauled.
Individual
inspection,
repair,
and fitting operations
previously covered in detail are made throughout
the reassembly procedure. The reassembly pro­
cedure
does
not cover accessories. If a new cylinder

block
fitted with pistons is used, many of the
operations
will
not be required.
Mount
the cylinder block in an
engine
repair stand.
If
an
engine
stand is not available, perform the fol­
lowing reassembly operation in a manner designed to protect personnel against an accident and the

engine
and its parts against damage.

Note:
During
engine
reassembly, use Perfect Seal

Aerosol
Spray
Sealer
Part
No.
994757
on all
engine
gaskets to ensure against vacuum, oil, gasoline and

water
leaks. Apply to head gaskets, valve covers,
water
pumps, oil pan gaskets, radiator and heater
hose
connections, felt gaskets, gasoline and oil line
connections, stud bolts,
spark
plug threads, and
grease retainer washers. Refer to manufacturer's in­
structions on container for proper application pro­
cedure.

D-79.
Install
Oil
Gallery
Plug

Coat
plug threads with a suitable sealing compound

and
install the plugs in the front and
rear
ends of
the oil gallery in the cylinder block and the
rear

end of the cylinder head. Torque the plugs 20 to 25 lb-ft. [2,8 a 3,4 kg-m.].

There
is also a pipe plug
(}/g,f
[3,2 mm.] slotted, headless) in the opening in the main oil gallery inside the cylinder block at No. 2 cylinder and another pipe plug
(}/g
"
square-head) in the opening

in
the oil passage directly below the oil pump intake
passage. If
these
two pipe plugs were removed,
make
certain they are reinstalled in the locations
described above or the counterweight of the

crankshaft
might strike the projecting head of the
square-head
plug.

D-80.
Install
Tappets

Turn
the block upside down. Beginning at the

rear
end of the cylinder block, install the intake

and
exhaust valve tappets in the tappet bores in the cylinder block in the following order: one
exhaust, two intake, two exhaust, two intake, and
finally
one exhaust valve tappet.

Check
the tappet to bore fit of each tappet as it
is installed in the block. If the stem-to-block

clearance
tolerance of .0005" to .002" [0,0127 a
0,051 mm.] is
exceeded
install a new tappet fitting
within
this tolerance or ream the bore to accomo­ date the next oversize tappet which is available

in
.004" oversize.

D-81.
Install
Camshaft and
Thrust
Plate

Lubricate
all camshaft bearings and cam surfaces generously with clean, light
engine
oil.
Carefully,

so not to damage or score the camshaft front bear­
ing,
install the camshaft, locating it properly in the bearings. Do not allow the
rear
end of the cam­shaft to strike sharply against the expansion plug

installed
in the
rear
end of the bore.
Install
the camshaft thrust plate. Slide the thrust
plate spacer
onto
the end of the camshaft with the
beveled inner
edge
of the spacer facing the cam­
shaft. If the same camshaft is being reinstalled,
install
any shims previously removed. These shims
are
placed
between
the camshaft shoulder and the

spacer.
Torque the thrust plate attaching
bolts
20
to 26 lb-ft. [2,8 a 3,6 kg-m.].

End
play of the camshaft is determined by running
clearance
between
the
rear
face of the camshaft
gear and the thrust plate. The standard clearance 62

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

D

FIG.
D-38—CHECKING
FLYWHEEL
RUN-OUT
place the flywheel on the mounting
bolts
in the

crankshaft.
When installing a new crankshaft or
flywheel, replace the tapered dowel
bolts
with
straight snug-fitting special
bolts
provided using

Flywheel
Dowel Bolt Installing Tool Kit W-231 as shown in Fig. D-35 and D-36. Assemble the

crankshaft
and flywheel in proper relation; then in­

stall
the straight
bolts
previously used and tighten
securely. Next, use the [13,9 mm.]
drill
to
enlarge the tapered holes. Ream the
holes
with the 5fo" [14,3 mm.] straight reamer and install the
two special flywheel
bolts
with nuts and lock­
washers in place of the two tapered dowel
bolts
formerly
used.
This
procedure overcomes the
necessity of reaming special tapered holes.

Tighten
the nuts alternately and evenly until each
is tightened 35 to 41 lb-ft. [4,8 a 5,7 kg-m.].

After
installation check the run-out of the flywheel

with
a
dial
indicator attached to the
engine
plate
as illustrated in
Fig.
D-38. Mount the
dial
indicator

with
the contact button of the indicator resting against the clutch face of the flywheel. Set the

indicator
at zero and rotate the flywheel. Maximum
allowable run-out is .008"
[0,203
mm.] near the
outer
edge
of the
rear
face of the flywheel.
With
the flywheel housing installed temporarily,
the alignment can be checked with a
dial
indicator. Without the clutch installed on the flywheel, a

dial
indicator can be mounted on one of the flywheel bolts. Set the
dial
indicator with the button resting
against the
rear
face of the flywheel housing. Ro­
tate
the flywheel, noting the run-out on the
indi­

cator.
Maximum allowable run-out is .005" [0,127
mm.].
Relocate the
dial
indicator so that the
button is against the side of the
rear
opening to
check the
radial
run-out. Rotate the flywheel and
note
the run-out which should not exceed .006" [0,152 mm.].

D-88.
Install
Flywheel Housing

Be
certain that the mating surfaces of the flywheel housing and cylinder block are clean and smooth.

Place
the flywheel housing in position and attach to the cylinder block and
engine
rear
plate. The
long
bolts
through the lugs on the
engine
crankcase
and
those
below are installed with the nuts on the
flywheel housing side.
Install
the other
bolts
from
the
rear
except the screw used to attach the top
side of the starting motor. Tighten securely.

D-89.
Install
Clutch

To
install the clutch assembly with the
engine
out
of the vehicle use a clutch plate aligning arbor.

Place
the clutch driven plate in position against
the flywheel. Insert the arbor into the clutch driven plate and clutch shaft bushing and expand the arbor

in
the bushing to hold it in place. Hold the clutch
pressure plate assembly in position against the
clutch
driven plate and install the attaching
bolts

and
washers, tightening the
bolts
alternately and
evenly. Remove the arbor.

D-90.
Install
Valves and Springs

Oil
the valve stems. Insert all intake and exhaust valves in the valve
guides
from which they were
removed.

Install
one exhaust valve spring and exhaust valve

spring
retainer (Roto Cap) for each exhaust valve.

Slip
the top end of the spring
onto
the
bottom
end
of the valve guide and, with a large screwdriver,
snap the spring and retainer over the tappet ad­

justing
screw. Make certain that the two closely wound coils of each spring are at the top (placed up to seat against the block.) See Fig. D-39.

Turn
the crankshaft as necessary to bring each
exhaust valve tappet to its lowest position. Using a
valve spring lifter, compress each exhaust valve

spring,
while holding the valve down, so that the
stem
extends
through the valve spring retainer
far
enough to permit installation of the valve

spring
locks. Heavy lubricating oil or grease
placed on the inside surface of the valve locks
will

help to hold the locks on the valve stem until the valve spring lifter can be removed. When installa­
tion of exhaust valves is complete, remove any
cloths used to block the valve compartment floor
openings.
Install
the intake valves and springs in the cylinder head placing the ends of the springs
having the closed coils down against the cylinder
head.
FIG.
D-39—VALVE
TAPPETS
AND
SPRINGS

65

D

HURRICANE
F4
ENGINE

FIG.
D-40—TIMING
GEARS Be
sure
to install a new rubber oil
seal
ring on each

intake
valve stem before installing the retainer

locks.
With
the retainer and spring compressed position a
seal
ring
on the valve stem just above the

lock
recess, then install the locks and release the
spring.

Adjust
the valve tappets to the proper specified

clearance.
Refer to Par. D-108, and specifications
at the end of this section for specifications and
adjustment procedure.

D-91.
Install
Camshaft
Timing
Gear

Turn
the camshaft or crankshaft as necessary so
that the timing marks on the two gears
will
be
together
after the camshaft timing gear is installed.

Refer
to Fig. D-40.
Install
the woodruff key in the key way on the front end of the camshaft.
Start
the large timing gear on the camshaft with the timing

mark
facing out. Do not drive on the camshaft gear, or the camshaft may
dislodge
the plug at the

rear
of the cylinder block causing an oil leak.
Install
the camshaft gear retaining screw and
torque it 30 to 40 lb-ft. [4,1 a 5,5 kg-m.] drawing
the gear
onto
the camshaft in the process. Standard
running
tolerance
between
the timing gears is .000" to .002" [0 a 0,051 mm.] which should be
checked with a
dial
indicator.

D-92.
Install
Timing
Gear
Oil Jet

Install
the timing gear oil jet in the tapped
hole

in
the front of the cylinder block. Position the oil

hole
in the side of the oil jet so that it
will
direct the

oil
stream against the camshaft driven gear just
ahead
of the point of
engagement
with the
crank­
shaft drive gear.

D-93.
Install
Oil Pump

The
oil pump is driven from the camshaft by means of a
spiral
(worm) gear. The distributor, in

turn,
is driven by the oil pump by means of a

tongue
on the end of the distributor shaft which
engages
a slot in the end of the oil pump shaft.
Because the
tongue
and the slot are both machined off center, the two shafts can be meshed in only
one position. Since the position of the distributor shaft determines the timing of the engine, and is
controlled by the oil pump shaft, the position of the oil pump shaft with respect to the camshaft is

important.

Turn
the crankshaft to bring
together
the timing
marks
on the crankshaft and camshaft gears. See

Fig.
D-4 0.
Install
the oil pump mounting gasket on
the pump.
With
the wider side of the shaft on top
(nearer
the top of the cylinder block), start the

oil
pump drive shaft into the opening in the left side of the cylinder block with the mounting
holes
in
the body of the pump in alignment with the
holes
in
the cylinder block. Insert a long-blade screw­

driver
into the distributor shaft opening in the

opposite
side of the block and
engage
the slot in the oil pump shaft.
Turn
the shaft so that the slot is positioned at what would be roughly the nine-

thirty
position on a clock face. Remove tne screwdriver and, looking down the

distributor
shaft
hole
with a flashlight, observe the position of the slot in the end of the oil pump shaft
to make certain it is properly positioned. Replace the screwdriver and, while turning the screw­

driver
clockwise to guide the oil pump drive shaft
gear into
engagement
with the camshaft gear, press
against the oil pump to force it into position. Remove the screwdriver and again observe the
position of the slot. If the installation was properly made, the slot
will
be in a position roughly equiva­
lent to eleven o'clock position on a clock face with
the wider side of the shaft
still
on the top. If the
slot is improperly positioned, remove the oil pump
assembly and repeat the operation.

Coat
the threads of the capscrews with gasket
cement and secure the oil pump in place with two
lockwasher-equipped capscrews installed through the body of the oil pump and into the cylinder block

and
one lockwasher-capscrew installed through
the oil pump mounting flange.

D-94.
Install
Timing
Gear
Cover

Apply
a thin coat of gasket paste to the timing
gear cover. Position the gasket on the cover and

carefully
locate the cover on the front of the front mounting plate. Attach the cover and timing

indicator
and tighten the bolts.

D-95.
Install
Pistons and Connecting Rods
Before installing each piston and connecting rod assembly in the cylinder block, generously lubricate
the entire assembly with
engine
oil. Space the ring
gaps
around the piston so that no two
gaps
are
aligned vertically and are not located over the
T-slot
in the piston
skirt.
Insert the assembly in
the correct cylinder with the connecting rod
identifying number toward the camshaft side of
the cylinder block. When installing each assembly, rotate the crankshaft so that the
crankpin
is in
the down position. Fit a piston ring compressor
tightly around the piston rings. Reach up from the
bottom
of the cylinder block and guide the end of
the connecting rod over the crankshaft
journal
as
the piston is tapped down into the cylinder bore

with
hammer handle. 66

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

D
Lubricate
the connecting rod bearing surfaces
generously with
engine
oil and install the bearing
cap with the numbered side matched to the num­
bered side of the connecting rod. Torque the nuts
evenly 35 to 45 lb-ft. [4,8 a 6,2 kg-m.]. The con­
necting rod cap nuts are locked with stamped nuts.

Used
stamped nuts should be discarded and re­
placed with new
ones.
These locking stamped nuts
should be installed with the flat face toward the
connecting rod nut.
Turn
the locking nut finger
tight and then 34
turn
more with a wrench. Refer
to Par. D-36 for detailed information on fitting pistons and rings in the cylinder bores.

D-96.
Install
Crankshaft
Pulley

Align
the keyway in the pulley with the woodruff key installed in the crankshaft. Drive the pulley

onto
the crankshaft and secure it in place with
the crankshaft pulley nut. Insert a block of wood

between
one of the counterweights on the
crank­

shaft and the side of the cylinder block to prevent the crankshaft from turning, then tighten the nut.

D-97.
Install
Oil Pan
Before installing the oil pan, make a final internal
inspection particularly making certain that the
inside of the cylinder block is clean. Apply a thin
coat of gasket paste on the oil pan. Place the new

oil
pan gasket in position. Set the oil pan in posi­
tion on the cylinder block and install the oil pan.
Torque
the attaching
bolts
12 to 15 lb-ft. [1,7 a 2,1

kg-m.].
Install
the oil pan
drain
plug and gasket

and
tighten the plug securely.

D-98.
Install
Cylinder
Head

Make
certain that the entire top of the cylinder

block
assembly, the lower surface of the cylinder

head,
and the cylinder head gasket are clean. Blow

all
dirt
or carbon out of the blind tapped bolt
holes

in
the cylinder block before the cylinder head and gasket are installed. Using aerosol spray sealer

Part
No. 994757, spray a thincoat on both surfaces
of the head gasket, position the new cylinder head gasket with the crimped
edges
of the gasket metal down (See Fig. D-31).
This
gasket position allows a
positive seal along the narrow surfaces of the
cylin­

der
head
between
the combustion chambers and
eliminates the possibility of burning combustion
10102

FIG.
D-41—CYLINDER
HEAD
BOLT
TIGHTENING
SEQUENCE
gases
reaching
an
asbestos
portion of the cylinder
head gasket.
Install
the cylinder head bolts. Tighten

the
bolts
with a torque wrench to 60 to 70 lb-ft. 8,3 a 9,7
kg-m.]
in the sequence shown in
Fig.
D-41.
Do not overlook installing the cylinder head bolt

in
the intake
manifold
directly under the
car­

buretor
opening.

D-99.
Install
Rocker Arm Assembly

a.
Insert
ball
ends of the intake valve push rods through the cylinder head and cylinder block and
seat them in the cupped head of the intake valve
tappets.

b.
Install
the
rocker-arm
assembly on the 'four

rocker-arm-mounting
studs. Align the rocker arms
so that the
ball
ends of the intake valve tappet

adjusting
screws fit into the cup ends of the push
rods.

c.
Install
the four rocker-arm-attaching nuts.
Thread
each nut down evenly in sequence, one

turn
at a time, until the torque is 30 to 36 lb-ft. [4,1 a 5,0 kg-m.].

d.
Cement a new gasket on the rocker arm cover.
Install
the cover placing an oil seal then a flat

washer
and nut on each cover stud. Cement a new gasket on the exhaust valve cover.
Install
the cover and crankcase ventilation fittings using a
new gasket back of the vent cover and new copper
ring
gaskets under the attaching screw heads.

Torque
the valve tappet cover nuts 7 to 10 lb-ft. [1,0 a 1,4 kg-m.].
D-100.
Install
Distributor and
Spark
Plugs

To
correctly install the distributor, it
will
be neces­

sary
to place No. 1 piston in the firing position.
To
locate the firing position of No. 1 piston, first

turn
the
engine
until No. 1 piston is moving up on
the compression stroke as indicated by compression

pressure
being forced through the
spark
plug open­

ing.
Turn
the
engine
slowly until the 5° before top
center
mark
on the timing gear cover is in align­
ment with the
mark
on the crankshaft pulley. Oil
the distributor housing where it bears on the
cylin­
der
block and install the distributor. Mount the

rotor
on distributor shaft and
turn
the shaft until
the rotor points towards No. 1
spark
plug terminal
tower position (when cap is installed, about 5
o'clock) with the contact points just breaking.
Move the rotor back and forth slightly until the

driving
lug on the end of the shaft enters the slot cut in the oil pump gear and slide the distributor
assembly down into place. Rotate the distributor body until the contact points are just breaking.
Install
the hold down screw.

Connect
the core
primary
wire to the distributor.

Clean
and adjust the
spark
plugs, setting the elec­

trode
gaps
at .030" [0,762 mm.].
Install
the plugs
to prevent any foreign matter entering the com­
bustion chambers during the remaining operations.
Torque
the
spark
plugs 25 to 30 lb-ft. [3,5 a 4,6

kg-m.].

Install
spark
plug cables, placing them in the dis­

tributor
cap terminal towers starting with No. 1

and
installing in a counter clockwise direction of
the firing order sequence (1-3-4-2). 67

D
HURRICANE
F4
ENGINE
D-101.
Install
Manifold

If
manifold studs were removed for replacement,
apply sealer on the stud threads
before
installing
a
new stud.
See Section Fl for exhaust emission controlled

engines.
Make
certain that no foreign objects are inside the manifold and that all
passages
are clear. Place a
new set of manifold
gaskets
in position on the side
of the cylinder block.
Then,
carefully slide the manifold
onto
the studs and against the cylinder block being careful not to damage the gaskets.
Torque
all manifold attaching nuts evenly 29 to
35 lb-ft. [4,0 a 4,8 kg-m.].
D-102.
Install
Oil
Filler
Tube

When
installing the oil filler tube, be sure that the
beveled lower end is away from the crankshaft.
Place a
piece
of
hard
wood
over the top of the
tube

to prevent damage to the cap gasket seat.
D-103.
Install
Water Pump

Make
certain that the mating surfaces of the water pump and the cylinder block are clean and smooth.
Install
the gasket on the
flange
of the pump and

install
the pump in position on the cylinder block.
Torque
the water pump attaching
bolts
alternately

and
evenly 12 to 17 lb-ft. [1,7 a 2,3 kg-m.].
D-104.
Install
Water Outlet Fitting

Install
the thermostat and the water
outlet
fitting.
Torque
the water
outlet
fitting attaching
bolts
20
to 25 lb-ft. [2,8 a 3,4 kg-m.].
FIG.
D-42—INSTALLING HURRICANE F4 ENGINE
IN
VEHICLE

1—
Lifting
Sling
2— Hoist
Cable

3—
Hurricane
F4 Engine
4— Dowel Bolt
5—
Flywheel
Housing
D-105.
ENGINE INSTALLATION
a.
Install
lifting sling to
engine
and using suitable hoist raise the
engine
from its blocking or stand

and
then slowly lower it
into
the
engine
compart­ment of the vehicle.

Note:
When installing the
Hurricane
F4 Engine,
two % x 4 inch
guide
bolts
or
dowels
should be
used to properly
guide
and align the
engine
to the
flywheel housing (See Fig. D-42).
b. Slightly tilt the
engine
downward and at the
same time slide the
engine
rearward
while lining up the transmission main gear shaft with the clutch
throw-out bearing and disc spline.

Note
:The
engine
crankshaft may have to be turned
slightly to align the transmission main gear shaft
with the clutch disc spline.
c. Remove the
guide
bolts
or
dowels
and secure
the
engine
to the housing.

d.
Secure the front
engine
mounts to the frame brackets and
bolt
ground cable to
engine.

e. Remove lifting sling from
engine.

f. Connect exhaust pipe to
engine
manifold flange.
g. Connect throttle and choke cables to carburetor.
h.
Install
fan to water pump pulley.
i.
Connect fuel pump line to main fuel line,

j.
Replace starting motor assembly. k. Connect
engine
wiring harness connectors at
front of cowl.

I.
Connect wires to starting motor assembly, water
temperature and oil pressure sending units and alternator.

NOTE:
ON
ENGINES EQUIPPED WITH EX­

HAUST
EMISSION CONTROL,
REPLACE
THE
AIR
PUMP,
AIR
DISTRIBUTOR
MANI­

FOLD,
AND
ANTI-BACKFIRE (DIVERTER)
VALVE.
SEE
SECTION
Fl.
m. Replace radiator and radiator grille support
rods and connect coolant
hoses
to
engine.

Note:
Replace heater
hoses
if vehicle is equipped
with hot water heater.

n. Fill
radiator with coolant and
engine
with oil
(see
Lubrication
Chart).

o.
Install
air cleaner and connect carburetor air
hose.

p. Connect battery cables and start
engine,

q.
Install
hood
and road
test
vehicle.
D-103.
FINAL
IN-VEHICLE
ADJUSTMENTS
a.
Clean
battery terminals and check battery. b.
Check
ignition terminals and check battery.
c. Service carburetor air cleaner.

d.
Service positive crankcase ventilation valve.
e.
Check
fuel lines. f. Gap and install new
spark
plugs.
g.
Check
distributor
points
and capacitor; replace
if
necessary. 68

'Jeep9
UNIVERSAL
SERIES
SERVICE
MANUAL

h.
Check
ignition (distributor) timing; reset if
necessary.

i.
Check
carburetor
adjustments; reset if necessary,

j.
With
engine
fully warmed up, tighten cylinder
head and manifold
bolts
and nuts to specified
torque.
Check
cylinder head gaskets and
bolts
for
air
or coolant leaks.

Note:
Tightness of cylinder head
bolts
should be
checked and corrected after 500 to 600 miles [800

a
960 km.] of normal operation.

k.
Check
fan belt tension; adjust if necessary.

I.
Check
for and correct any oil leak, fuel leak or
coolant leak.
D-107.
VALVE
ADJUSTMENT

Proper
valve adjustment is important to prevent
burning
of valves and poor
engine
performance.

This
adjustment consists of obtaining a specified

lash
in the valve mechanism. The exhaust valve
tappets and the intake valve rocker arms should be adjusted to the proper clearance with the
engine

cold (at room temperature). Valve clearance can
be properly adjusted only when the tappet is on the
heel or low portion of the cam.
INTAKE

OPENS

9°
BTC?

FIG.
D-43-
10270

-VALVE
TIMING
D-108. Valve Adjustment Procedure

The
exhaust valve tappets are adjusted by turning
the adjusting screw in or out of the tappet as neces­
sary
to obtain the proper clearance. Where special
wrenches can be obtained, they should be used to facilitate the adjustment. The proper clearance is .016" [0,406 mm.]
between
the end of the adjusting
screw and the
bottom
of the exhaust valve.

Crank
the
engine
over to
close
a valve and check
the clearance with a feeler
gauge.
To adjust, hold
the tappet with one wrench and
turn
the adjusting

screw,
with the other.
Check
and adjust each of
the tappets in proper sequence.

Adjust
each intake valve by adjusting the rocker
arm
screw at the push rod to obtain .018" [0,457 mm.] clearance
between
the rocker arm and the
valve stem with tappet on the heel of the cam.
D-109.
Check
Valve
Timing

To
check the valve timing, carefully set the intake
valve rocker arm adjustment for No. 1 cylinder to .026"
[0,6604
mm.]
between
the rocker arm and the
valve stem. Rotate the crankshaft clockwise until
the piston in No. 1 cylinder is ready for the intake stroke. The intake valve
opens
9° before top center
(BTC).
Note
the distance
between
the
"TC"
and
"5°"
marks on the indicator on the timing gear
cover and estimate the 9° before top center position.
See
Fig.
D-43.
With
the crankshaft in this position, timing is correct if the rocker arm is just tight
against the intake valve stem. Do not overlook resetting the rocker arm adjustment to the correct

running
clearance.
D-110. Positive
Crankcase
Ventilation

Be
sure there are no air leaks at the tube connec­
tions
between
the air cleaner and the oil filler tube,

and
that the oil filler tube cap gasket is in
good

condition. Always keep the cap locked securely in
place. When tuning the
engine
or grinding valves, remove the control valve and clean it thoroughly.
If
the valve is blocked with carbon, the ventilating
system
will
not operate and, should the valve

fail
to seat, it
will
be impossible to make the
engine

idle satisfactorily. Refer to Par. C-6 for servicing.
D-111. Oil
Filter

The
engine
is equipped with a throw-away type

oil
filter.
This
oil filter must be serviced periodi­
cally
as outlined in the
Lubrication
Section. 69

Dl

DAUNTLESS
V-6
ENGINE
DM.
GENERAL

This
section describes service and repair of the
Dauntless V-6 engine. The
engine
code
number shown in
Fig.
A-4 is provided to identify the Daunt­

less
V6-225 engine. The meaning of the coded letters and numbers that are stamped on the right front face of the crankcase, just below the rocker
arm
cover,
between
exhaust manifold ports, is given
below.
Letter
to
Designate
Market

M
—
Military
E
—
Export

D
— Domestic
Letter
to
Designate
Year
Built

N
— 1967
P
— 1968

R
— 1969
S
— 1970

T
— 1971

Letter
to Designate
Engine
and Compression
Ratio

H—V6-225
9.0 to 1
C.R.
(2 Bbl.
Carb.)
Y—V6-225
9.0 to 1
C.R.
Marine
(Low
Profile)
(2
Bbl.Carb.)
Z—V6-225
9.0 to 1
C.R.
Marine
(High
Profile)
(2 Bbl.
Carb.)

K—V6-225
7.6 to 1
C.R.
(2 Bbl.
Carb.)
L—V6-225
7.4 to 1
C.R.
(2 Bbl.
Carb.)

Market

Domestic
—

Year
"1967"
Engine
J

Day

Plus Chg. If
Any-
Service Engine "S"
Short
Block
"R" -Oversize Bores "B"
Undersize Crank

&
"A"

Rod
Bearings

The
identifying letter or letters follow the
engine
letters are decoded as follows:
A—.010"
Undersize
Main
and Connecting Rod
Bearings

B—.010"
Oversize Pistons

AB—Combination
of A and B
S—Service
Engine

R—Short
Block

All
disassembly and assembly procedures are pre­ sented in logical order, assuming a complete
engine

overhaul
with
engine
removed from the vehicle.

However,
many of
these
procedures can also be
performed as on-vehicle services if vehicle or
engine
components are removed to gain access to parts
involved.

Note:
Some
engines
are equipped with an exhaust
emission control system. Service information on
the components of this system is given in sec­ tion F2.

Dl-2.
ENGINE
DESCRIPTION

The
Dauntless V-6
engine
has a displacement of
225 cubic inches. It has a compression ratio of
9.0 to 1, which permits use of regular-grade
gaso­

line.
See
Figs.
Dl-1 and Dl-2.

The
cylinder block is made of cast
iron.
Two banks
of cylinders (three cylinders per bank) are cast at a
90-degree
angle. The lower part of the cylinder-

block
extends
below the centerline of the
crank­
shaft, forming a continuous flat surface with the

rear
crankshaft main bearing cap and the timing

chain
cover.
This
design allows installation of an
oil
pan with a
one-piece
gasket. The cylinders in
the left bank (as viewed from the driver's seat) are
numbered
1-3-5,
from front to
rear.
The cylinders

in
the right bank are numbered
2-4-6,
from front
to
rear.

The
crankshaft is supported in the cylinder block
by four steel-backed full-precision bearings, all of

which
have an identical diameter.
Crankshaft
main bearings are numbered 1 to 4, front to
rear.
The

thrust
bearing is flanged to maintain crankshaft position and to compensate against crankshaft end

thrust
The No. 2 bearing is the thrust bearing.

The
crankshaft is counterbalanced by weights,
which
are cast integral with the
crank
cheeks. The

weights
are shaped to a contour which
gives
mini­
mum
clearance with cylinder barrels and piston

skirts
to conserve space.

Connecting
rods have I-beam sections with
bosses

on each side. Metal is removed, as required, to secure correct weight and balance. The lower end
of each connecting rod has a steel-backed preci­
sion bearing. The piston pin is a press fit into the upper end. The outer ends of the piston pin

are
a slide fit in the piston
bosses.

The
full-skirted, aluminum alloy pistons are cam ground and tin plated. Two compression rings and
one oil control ring are installed above the piston
pin.
The cast iron compression rings in the two

upper
grooves
of the piston have a
groove
or bevel cut around the inner
edge
on one side. The
top compression ring is installed with this
groove
or
bevel up. The lower compression ring is installed

with
bevel down. The oil
ring,
in the lower groove,
consists of two thin steel
rails
separated by a

spacer.
It is backed by a hump-type spring-steel
expander.

V-6
engine
cylinder heads are made of cast
iron.

Their
valve
guides
are cast integrally. Right and left cylinder heads are identical and interchange­
able. In service, however, it is
good
practice to
install
the cylinder heads on the side from which
they were removed.

The
valves are in line in each head, at an angle
10°
above the centerline of the cylinder bores.

Each
valve has a spring strong enough to ensure
positive valve seating throughout the operating speed range of the engine. The valve rocker arm
mechanism is protected by a
sheet
metal cover.
This
cover is seated on a raised surface of the
cylinder
head. It is gasketed to prevent oil leaks.

The
rocker arms for each bank of cylinders are mounted on a tubular steel shaft, supported on
the cylinder head by brackets. The rocker arms
are
made of aluminum. They have inserts at the

push
rod socket and the valve stem contact face.

The
camshaft is located above the crankshaft be­
tween the two cylinder banks; it is supported in
four steel-backed babbitt-metal bearings. The cam­ shaft is driven at one-half crankshaft speed by
sprockets and a single outside-guide type chain.

Hydraulic
valve lifters and
one-piece
push rods operate overhead rocker arms and valves of both

banks
of cylinders from a single camshaft.
This

system requires no lash adjustment during assem­
bly
or in service.

In
addition to its normal function of a cam follower,
each hydraulic valve lifter also serves as an auto- 76

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

Dl

12710

FIG.
D1
-3—HYDRAULIC VALVE
LIFTER
ASSEMBLY, CROSS-SECTIONAL VIEW
1—
Snap
Ring
6—Ball Retainer

2— Rod
Seat
7—Plunger Spring

3—
Oil
Inlets
8—Lifter
Body

4—
Plunger
9—Bronzed
Cap
5— Feed
Hole
sages
in the block and cylinder head.

The
water cooled system is pressurized to provide efficient
engine
cooling. It consists of a centrifugal-
type water pump, mounted on the timing chain cover, and is driven by the
engine
fan pulley. The
pump provides coolant flow equally to both
cylin­
der banks under control of a thermostat. Coolant
flow is around the cylinders and through the
cylinder
head to dispel the heat of combustion in
the engine.

Dl-3.
Engine Mounts

The
engine-transmission unit is mounted to the chassis at three points by rubber pads. The two
front mounts are bolted to the
engine
cylinder
block and the frame members. These mounts sup­ port most of the
engine
weight, and absorb
vibra­

tion which would otherwise be caused by changes
in
engine
output torque. The single
rear
mount is
placed
between
the transmission and the trans­ mission support. It supports part of the engine'

and
transmission weight, and locates the
rear
of
the
engine
with respect to the centerline of the
vehicle.

Dl-4. ENGINE REMOVAL
To
remove the
engine
from the vehicle follow the
procedurers listed below:

a.
Remove hood. b. Disconnect battery cables from battery and
engine. c. Remove air cleaner.

d.
Drain
coolant from radiator and engine.
e.
Drain
engine
oil.
f. Disconnect alternator wiring harness from con­ nector at regulator.

cj.
Disconnect the fuel evaporative purge line con­ nected to the
P.C.V.
valve.

h.
Disconnect upper and lower radiator
hoses
from
the engine.

i.
Remove right and left radiator support
bars,

j.
Remove radiator from the vehicle.

k.
Disconnect
engine
wiring harnesses from con­
nectors located on
engine
firewall.
I.
On
engines
equipped with exhaust emission con­

trol,
remove the air pump, air distribution manifold,

and
anti-backfire (gulp) valve. See Section F2 for
procedure.

m.
Disconnect battery cable and wiring from en­

gine
starter assembly.

n.
Remove
engine
starter assembly from engine,

o.
Disconnect
engine
fuel
hoses
from fuel lines at

right
frame
rail,
p. Plug fuel lines.

q.
Disconnect choke cable from carburetor and cable support bracket mounted on engine,
r.
Disconnect exhaust pipes from right and left

engine
manifolds.
s. Place
jack
under transmission and support trans­
mission weight.
f. Remove
bolts
securing
engine
to front motor mounts.

u.
Attach suitable sling to
engine
lifting
eyes
and,
using hoist, support
engine
weight.
v. Remove
bolts
securing
engine
to flywheel housing.
w. Raise
engine
slightly and slide
engine
forward
to remove transmission main shaft from clutch plate spline.

Note:
Engine and transmission must be raised
slightly to release the main shaft from the clutch
plate while sliding the
engine
forward.
x. When
engine
is free of transmission shaft raise

engine
and remove from vehicle,
y. Place
engine
on suitable blocking or
engine
stand and remove sling from engine.

Dl-5.
ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some of the operations of the procedure are also appli­cable separately with the
engine
in the vehicle,
provided that wherever necessary the part of the
engine
to be worked on is first made accessible by removal of
engine
accessories or other parts.

When
the disassembly operations are performed
with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have
been removed
prior
to starting the disassembly and
the oil has been drained.

Dl

DAUNTLESS
V-6
ENGINE
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle, special instructions are given to cover different
operations required when disassembly is
done
with
the
engine
installed.

During
disassembly operations, the
engine
should be mounted in a suitable
engine
repair stand.

Where
practicable, modify or adapt an existing re­

pair
stand as necessary to accommodate the
engine.
If
an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that
will
protect personnel against an accident and the
engine
and its parts against damage.

Dl-6.
Mounting Engine
On
Engine Stand

Refer
to Fig. Dl-4.
a.
With
the
engine
supported by a hoist, remove
the clutch housing and clutch. Match
mark
the flywheel and the clutch cover before disassembly to assure proper reassembly.
b. Position the
engine
on the
engine
stand.
c. Release
some
tension of the hoist cables and secure
engine
to stand.

d.
Make sure the position lock on the
engine
stand
is tight to prevent the
engine
from accidentally
inverting.

e.
Release the hoist cables.
FIG.
D1
-4—ENGINE
MOUNTED
ON
STAND

1—
Spacer
J-8690-6
A—Bolt,
i/2-NC
x 3i/2"

2—
Bolt,
3/a-NC
x 4*/2" 5—Adapter 21316-J 3—
Engine
Mounting Stand
Dl-7.
Remove Intake Manifold
and

Carburetor Assembly

Disconnect crankcase vent
hose,
distributor vacuum

hose,
and fuel line from carburetor. Disconnect two distributor leads from ignition coil. Disconnect

wiring
harness from coolant temperature sending

unit.
Remove ten cap
bolts
which attach intake
manifold to cylinder heads. Remove intake mani­
fold assembly and gaskets from
engine.

Dl-8. Remove Exhaust Manifold
The
engine
has two exhaust manifolds. Remove five attaching screws, one nut, and exhaust mani­
fold from each cylinder head.

Dl-9.
Remove Distributor

Disconnect vacuum
hose
and wiring harness from

distributor.
Disconnect spark plug cables from
spark
plugs. Remove sparks plugs from
engine.
Pull

spark
plug cable retainers from brackets on rocker

arm
covers. Remove mounting screw, retainer

bracket,
and distributor from timing chain cover.
If
timing chain and sprockets are not to be re­
moved from
engine,
note
position of distributor
rotor so that it can be installed in identical position.

Dl-10. Remove
Fuel Pump
Disconnect output fuel line from fuel pump. Re­
move
two mounting bolts, fuel pump, and gasket

from
timing chain cover.

Dl-11.
Remove Alternator
and Fan
Belt

Disconnect wiring harness from alternator. Remove nut and flat washer which fasten alternator to
adjustment bracket. Pivot alternator
inward,
to­

ward
engine
cylinder block, to relieve fan belt
tension. Remove fan belt from pulleys. Remove
two attaching screws, mounting bracket, and alter­ nator from right cylinder head of
engine.

Dl-12.
Remove Cooling
Fan and
Water Pump

Refer
to Fig. Dl-5.
Remove four cap screws, lock washers, cooling fan,

fan
hub, and fan drive pulley from flange of water
pump shaft. Remove nine attaching screws, water
pump, alternator adjustment bracket, and water pump from timing chain cover.

Dl-13.
Remove
Oil
Filter

Unscrew
oil filter from
engine
oil pump.

Dl-14.
Remove Starter Motor

Disconnect wiring harness from starter motor and
solenoid. Remove two attaching screws, starter motor, solenoid, and motor attaching bracket from

engine
flywheel housing and cylinder block.

Dl-15.
Remove
Oil
Pressure Sending Unit

Disconnect wiring harness from oil pressure send­
ing unit. Remove oil pressure sending unit from

engine
cylinder block.

Dl-16.
Remove
Oil
Dipstick

Withdraw
and remove oil level dipstick and dip­

stick
tube
from
engine
cylinder block.

Dl-17.
Remove Crankshaft Pulley

Remove six attaching screws and crankshaft pulley

from
crankshaft vibration damper. 80

Dl

DAUNTLESS
V-6
ENGINE
This
will
prevent damage to piston rings or
crack­

ing piston lands during removal.
b. Use a silver pencil or quick-drying paint to mark
the cylinder number on all pistons, connecting rods,
and
caps. Starting at the front end of the crankcase,
the cylinders in the right bank are numbered 2-4-6
and
in the
left
bank are numbered
1-3-5.

c. Remove cap and lower connecting rod bearing

half
from No. 1 connecting rod.

d.
Push the piston and rod assembly away from
the crankshaft and remove it from top of cylinder bore. Then install cap and lower bearing half on
connecting rod.
e. Remove each connecting rod and piston as­ sembly as described in c and d, above.
FIG.
D1-9—CRANKSHAFT
MAIN
BEARING
CAPS

1—Thrust
Bearing
D1-32.
Remove
Main
Bearing and Crankshaft
a.
This
engine
has four crankshaft main bearings.

Front
to
rear,
they are numbered 1 to 4. Refer to

Fig.
Dl-9. With a silver pencil or quick-drying
paint, mark the bearing number on each main bearing cap.
b. Remove two
bolts
which secure first (front)

main
bearing cap to
engine
cylinder block. With

a
lifting bar, carefully pry the cap from the crank­ shaft and block. Be careful not to damage the cap,
block or crankshaft. Remove the bearing cap, with
lower main bearing half, from the cylinder block.

Keep
bearing half and cap
together.
Similarly, remove the next two main bearing caps with lower

main
bearing halves. To remove
rear
main bearing
cap,
use
rear
main bearing remover bolt W-323.
c. Remove the fabric seal from inside diameter of
fourth (rear) main bearing cap, and remove neo-
prene composition seal from outer surface of this
bearing cap. Discard both seals.

d.
Lift
and remove the crankshaft from
engine
cylinder
block. Do not remove upper main bearing
halves from block or lower main bearing halves

from
caps at this time. Mount main bearing caps

in
their original positions.
Dl-33.
ENGINE
CLEANING,
INSPECTION,

AND
REPAIR

The
cleaning, inspection, and repair procedures
detailed herein are recommended to be followed
when a
complete
engine
overhaul is to be made
with the
engine
out of the vehicle. These instruc­
tions
can generally be applied individually with the

engine
in the vehicle. Wherever the procedure dif­
fers due to the
engine
being in the vehicle, the necessary special instructions are provided. Inspec­
tion and repair instructions are included to cover
the cylinder block, cylinder head, crankshaft and bearings, connecting rods and bearings, oil pump,
valves and tappets, pistons and rings, flywheel,
timing gears, and the camshaft and bearings. In
addition, fitting operations for
these
engine
com­

ponents
are included.

D1-34.
Cylinder Block

The
cylinder block must be cleaned thoroughly, inspected, and repaired as necessary, as described
below.

Dl-35.
Cylinder Block Cleaning
Steam-clean the cylinder block, or clean it with

a
suitable cleaning solvent A scraper can be used
to remove
hard
deposits, but do not score machined
surfaces. Be certain that oil passages, valve cham­

bers,
crankcase, and cylinder walls are free from sludge, dirt, and carbon deposits. After cleaning,

dry
the cylinder block carefully with compressed
air.

Dl-36.
Cylinder Block Inspection

a.
Inspect cylinder walls visually for scoring,
roughness, or ridges which indicate excessive wear.
Check
cylinder bores for taper and out-of-round
with an accurate cylinder
gauge.
Measure eact bore at top, middle and bottom, both parallel tc
and
at right
angles
to the centerline of the
engine

The
diameter of the cylinder bores at any poin
FIG.
Dl-10—MEASURING
CYLINDER
BORE

1—Telescope Gauge [90*
From
Piston Pin]
84