engine KIA CADENZA 2016 Features and Functions Guide

Page 19 of 50

17
M I S T: Single wipe
OFF: Wiper off
AUTO: Auto Control* wipe
LO: Slow wipe
HI: Fast wipe
Windshield Wipers & Washers
To o p e r a t e :
• Move lever Up/Down to change Wiper modes
• Pull lever to spray and wipe
Auto Control (Rain Sensing)*
The rain sensor located on the upper end of the windshield
glass senses the amount of rainfall and controls the wiping
cycle for the proper interval The more it rains, the faster the
wiper operates When the rain stops, the wiper stops
To adjust the Auto Rain Sensing speed setting, move the
speed control switch
A up/down


•With the ENGINE START/STOP button in the ON position and
the wiper switch is in AUTO mode, the wiper will operate once
to perform a self-check of the system

•Moving lever to HI increases Intermittent wipe frequency and
wipe speed Moving lever to LO decreases frequency of wipes

•Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
A
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

Page 23 of 50

21
Your vehicle’s steering wheel buttons may differ from those in the illustrations. See your Owner’s
Manual for more details.
Audio Controls* Cruise Control*
E CRUISE Control ON/OFF button: Press to turn the Cruise Control
ON/OFF
F Resume Cruising Speed button: Press to resume or increase
cruising speed
G Set Cruising Speed button: Press to set or decrease Cruising Speed
H Cruise Control CANCEL button: To cancel Cruise Control setting, do
one of the following:

• Press the brake pedal

• Press the CANCEL button
A Audio Mode button: Press to cycle through FM 1-2/AM/Sirius® 1-3 /
USB/iPod®/Aux / Bluetooth® Audio Streaming/My Music modes
B Seek/Preset button:
FM/AM/Sirius® Modes: Press to advance through Preset Stations
Press and hold to auto seek

Media Modes: Press to move Track Up/Down Press and hold to Fast
Forward / Rewind
C Volume button: Press up/down to raise/lower volume
D MUTE button: Press to mute all audio
Driving while distracted is dangerous and should be avoided. Drivers should remain attentive to
driving and always exercise caution when using the steering-wheel-mounted controls while driving.
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
CANCELCRUISE
RES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SET
VOL
VOL
MUTEMODE
CANCELCRUISERES
SETVOLVOL
MUTEMODE


Pressing the Audio Mode button for more than 1 second will turn Audio Mode ON/OFF QUICK TIP

•Cruise Control is designed to function above 25 mph
•The Cruise Control system will not activate until the brake pedal has been
depressed at least once after ignition ON or engine start
QUICK TIPS
AD
CB
E
H
F
G
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
STEERING WHEEL CONTROLS

Page 24 of 50

22


UVO eServices with
Navigation System

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www.KuTechVideos.com/audio/
nav_eServices
UVO eServices with Navigation*
– FM/AM/Sirius®/Media (CD, MP3, USB, iPod®, Aux, Bluetooth® Audio Streaming, My Music)
CD-INDISP
PWRPUSH
VOL TUNE
FILE
DEST
SEEK TRACK
MEDIA
FM/AM
PHONE S AT
MAP
VOICE
ROUTEMAP
Press to turn display ON/OFF Press to reset the system
Press to display MAP of the current position
Press to display destination mode
Press to display Info/UVO eServices/
Setup mode
Press to display ROUTE mode
Press to display PHONE mode
Press to turn audio system ON/OFF
Press and hold to turn Power OFF Rotate to adjust Volume
Press to select previous/next Radio/SiriusXM
® stations/Media tracks/files.
Press and hold to move quickly through stations/tracks/files Press to select FM/AM modes
Press to select SiriusXM
® mode
Press to select MEDIA mode
Press to eject CD
Rotate to change Radio/SiriusXM
®
Stations/Media tracks/ files


•Prolonged use of the UVO eServices with Navigation system in ACC mode may
drain the vehicle’s battery A warning screen may appear periodically to remind
users that the system should be operated with the engine running to prevent
battery discharge

•When using the voice command feature, wait for the system BEEP before
speaking the command
QUICK TIPSUVO eServices Registration/Activation – To use UVO eServices:
1 Register through your UVO eServices App or at MyUVO com
2 On your Smartphone, go to an app store or marketplace to download
the UVO eServices App and log in to the app using your MyUVO com
account credentials
3 Follow the App’s phone pairing and activation steps
For further operational information,
refer to the Car Multimedia System
User's Manual. Your vehicle’s audio
system may differ from that in
the illustration.
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

Page 25 of 50

23
Surround View Monitor (SVM)*
The Surround View Monitor (SVM) system is a parking support system that shows the areas around the front, rear, left, and
right sides of the vehicle via four cameras displayed onto the navigation screen The SVM system will turn on when the SVM
button
A is pressed and the LED is illuminated


Surround View
Monitor Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
Front SVM - when in Drive & Neutral: Rear SVM - when in Reverse:
Displays the front side and SVM images
simultaneously on the screen
Displays the front side image on the
screen
Displays the front side and left side
images simultaneously on the screen
Displays the front side and right side
images simultaneously on the screen
Displays the rear view and SVM images
simultaneously on the screen
Displays the rear side image on the
screen
Displays the rear and left side images
simultaneously on the screen
Displays the rear and right side images
simultaneously on the screen
REMINDER: The SVM camera is
equipped with an optical lens to
provide a wider range of vision and
may appear different from the
actual distance
The Surround View Monitor system
is only a supplemental device.
Drivers should not rely solely on the
SVM information when parking and
backing up. Drivers should always
pay attention and directly check the
left/right and rear.

• The Front SVM camera is ON when the ENGINE START/STOP
button is On, the gear shift is in Drive or Neutral and the SVM
button is pressed ON

• Rear SVM: The camera view will automatically display on the
navigation screen when the vehicle is shifted into Reverse
The camera view will turn off when the vehicle is shifted out
of Reverse

• Front SVM: The camera view will display on the navigation
screen in both Drive and Neutral In Drive, the camera
view will continue to display until the vehicle is above
approximately 12 mph The camera view will reappear on
the navigation screen whenever the vehicle drops below
approximately 12 mph
Camera View Modes – To change camera view modes, press the icons shown below on the navigation screen to select the mode


The Front SVM camera will turn off when the gear shift is
moved into Park or Reverse or the SVM button is pressed QUICK TIP
Check yo ur sur roun dings for safety.
(Button located on gear shift)
A
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

Page 26 of 50

24
REMINDER: Using the power outlet (accessory plug) for
prolonged periods of time with the ENGINE START/STOP
button in the ACC position (Engine OFF ) could cause the
battery to discharge
For more information on the Aux/USB/iPod
® Port & Power
Outlets, refer to the Owner's Manual.
Aux/USB/iPod® Port
& Power Outlets
Clock

USB Port Video


To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
Center Panel Clock Setup:
Clock setup is done through the UVO eServices with Navigation
system See below or refer to the Car Multimedia System User's
Manual for more information
UVO eServices with Navigation* Clock Setup:
Press the Info/Settings key
on the audio control unit Then
press the on-screen Setup button and select the Clock icon Use the
on-screen buttons to navigate through setup
CLIM AT E
MODEACPASS
AIR BAG
OFF
AUTOFRONT
REAR
OFF
DUAL
AUX USB
If equipped, additional power outlets are
located inside the center console



Press the DONE button on the navigation screen to ensure changes
are saved QUICK TIP


The power outlets are inactive when the ENGINE
START/STOP button is OFF QUICK TIP
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

Page 29 of 50

27
Auto-Hold*
Auto-Hold temporarily maintains the vehicle
at a standstill even if the brake pedal is
released Auto-Hold can be turned ON/OFF
using the AUTO HOLD switch
B on the
driver’s panel Before Auto-Hold will operate,
the driver’s door, engine hood and trunk
must be closed, and the driver’s seat belt
must be fastened
The Auto-Hold indicator has four states:
White: Standby - With vehicle at a standstill,
and AUTO HOLD switch
B turned ON, the
indicator will illuminate white While driving
the vehicle (vehicle is not at a standstill), the
Auto-Hold indicator will remain white
Green: Engaged - When coming to a
complete stop by depressing the brake
pedal, the Auto-Hold indicator changes from
white to green
OFF (not illuminated) - The indicator will turn OFF when the AUTO HOLD
switch
B is manually turned OFF or when the EPB is manually turned ON
Yellow: Malfunction - When the indicator is illuminated yellow, there may
be a system malfunction Take your vehicle to a local Kia dealer
Refer to page 4 for location of Instrument Cluster indicators.

Electric Parking Brake*
The Electric Parking Brake (EPB) system utilizes
an electric motor to engage the parking brake
Applying the Parking Brake
Depress the brake pedal and pull up the EPB
switch
A Ensure that the indicator light is
illuminated on the instrument cluster
Releasing the Parking Brake
The EPB will automatically release when the shifter
is placed in Reverse or Drive
To release EPB manually, depress the brake pedal, then press the EPB
switch
A, with the ignition switch in the ON position Ensure that the
indicator light
i s O F F
REMINDERS:

• As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds
when the ignition switch is turned ON

• If the warning light does not illuminate temporarily, or continues to remain lit, take your
vehicle to an authorized Kia dealer and have the system checked

• The EPB should not be operated while the vehicle is moving, unless there is an
emergency situation

• A click or electric brake motor sound may be heard while operating or releasing the EPB,
but these conditions are normal and indicate that the EPB is functioning properly


Electric Parking
Brake Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
(Buttons located below Gear Shift)


•When leaving your keys with parking lot attendants or valet, make sure to inform
them how to operate the EPB

•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a
firmer EPB application

•Pull up and hold EPB switch again to increase brake pressure if parked on a
decline or incline
QUICK TIPS
A
B
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
CENTER PANEL

Page 30 of 50

28
Heated Steering Wheel*
Press Heated Steering Wheel button A to turn ON/OFF Steering Wheel
Heater, while the ENGINE START/STOP button is in the ON position Steering
Wheel Heater will turn off automatically in 30 minutes, or when button is
pressed again to deactivate
Power Rear Sunshade*
Press the Power Rear Sunshade button B to raise/lower sunshade, while
the ENGINE START/STOP button is in the ACC/ON position
(Buttons located below Gear Shift)


•If ignition is turned OFF, then ON again within 30 minutes of Steering Wheel
Heater being turned ON, the system will remain in the ON position

•System does NOT turn off when ignition is cycled To turn off system, press the
Heated Steering Wheel button
QUICK TIPS


1 The Power Rear Sunshade will lower when the Gear Shift is moved into the R
(Reverse) position
2 Then when the Gear Shift is moved into D (Drive) and vehicle’s traveling more
than 12 mph, the Power Rear Sunshade will unfold automaticallyQUICK TIPS
A
B
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
CENTER PANEL

Page 33 of 50

31
Front Seat Headrest Adjustment
To adjust headrest forward: Pull headrest forward at an angle
To adjust headrest back: Pull forward at a slight angle to the farthest
position and release Then pull forward to desired position
To raise headrest: Pull headrest up
To lower headrest: Press lock
A, then press the headrest down
Driver Position Memory System*
The integrated system stores into memory the position
of the Driver’s Seat, Outside Rearview Mirrors and the
Steering Wheel
To store positions into memory, first place the Gear
Shift into P (Park) while the ENGINE START/STOP
button is in the ON position Then:
1 Adjust the Driver’s Seat, Outside Mirrors and the
Steering Wheel
2 Press the Memory button
B on the control panel
System will beep once
3 Press one of the memory buttons
C within 5
seconds The system will beep twice when memory
has been stored
M
1
2
(Buttons located on
Driver's Door Panel)
A
B
C
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
SEATING

Page 34 of 50

32
Smart Key
A Press to lock All Doors
B Press to unlock Driver’s Door Press twice in 4 seconds to unlock All Doors
C Press and hold for more than 1 second to unlock Trunk and manually open
REMINDERS:

•Trunk lid will partially open To fully open, lift up manually

•The Trunk unlocks when the Smart Key is within close proximity of the vehicle
D Press and hold more than 1 second for Panic Alarm To turn off Alarm, press any button
E Press to release Mechanical Key (Button on reverse side of fob)
REMINDERS:

•Remote button configuration may vary depending on vehicle options

• The Smart Key’s signal can be blocked by the normal operation of a cell phone or smartphone To help prevent
this, store each device separately


Engine Start/Stop Button
& Smart Key Video

To view a video on your
mobile device, snap this
QR Code or visit the listed
website
Refer to page 2 for more
information QR CODE
www. KuTechVideo s.c om/vg13/2016
Driver’s Door Lock/Unlock button G:
To unlock door(s):

• Press button once to unlock
Driver’s door

• Press again within 4 seconds to
unlock all doors
To lock all doors - Press again to lock all doors


If the Smart Key battery is weak or not working properly, hold the Smart Key fob up to the ENGINE
START/STOP button (Lock button side closest) and press to start engine QUICK TIP
A
B
C
D
F
E
G
UnlockLock
Mechanical Key F:
Use to unlock /lock Driver’s Door 1 Remove door handle keyhole cover with Mechanical Key
by pressing up into slot as shown
2 Insert Mechanical Key and turn right to Unlock Driver’s
Door Turn twice within 4 seconds to Unlock all doors
3 Insert Mechanical Key and turn left to Lock
Driver’s Door
4 Return keyhole cover to its original position
Use to lock glove box and to turn Child Safety Locks
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

Page 36 of 50

34
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30 seconds after the ENGINE
START/STOP button is OFF
Map/Room Lamp Operation
Press the buttons
A to turn the Map Lamps ON/OFF This light produces a spot
beam for convenient use as a map lamp or as a personal lamp for the driver or the
front passenger
Room Lamp - Press the lens
B to turn the Room Lamp ON/OFF
The Map and Room Lamps turn ON when button
C is pressed any door is opened
or the ignition is turned OFF When all doors are locked or the ignition is ON, the Map
Lamp will turn OFF immediately The Map and Room Lamps turn ON for approximately
30 seconds
REMINDER: When Room Lamp lens is pressed ON it will remain ON, even when the Map Lamp switch is in the
OFF position


•When doors are unlocked by the Smart Key*, the lamp turns ON for approximately 30 seconds
•If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off
approximately 3 seconds after the system is in armed stage

•Using interior lights for an extended period of time may cause battery discharge
QUICK TIPS
AA
A
BC
CADENZA FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES

Page:   < prev 1-10 11-20 21-30 next >