electrical LAND ROVER DISCOVERY 1995 User Guide

MAINTENANCE
11
MAINTENANCE
CHECK/ADJUST ENGINE IDLE SPEED - Tdi
For idle speed.See ENGINE TUNING DATA,
Information, 300 Tdi Engine
CHECK ENGINE IDLE SPEED - Mpi
For idle speed.See ENGINE TUNING DATA,
Information, Engine - Mpi - 2.0 Litre
CHECK/ADJUST STEERING BOX V8i - Tdi - Mpi
Check steering box for fluid leaks.
Check that there is no backlash in steering box in
straight ahead position. Adjust steering box if
necessary.
See STEERING, Adjustment, Power
Steering Box
CLEAN BATTERY CONNECTIONS
NOTE: Some 96 models are fitted with
battery backed-up sounder
See
ELECTRICAL, Repair, Battery
Remove battery terminals, clean and coat with
petroleum jelly.
A low maintenance battery is installed in vehicle.
Dependent upon climate conditions electrolyte levels
should be checked as follows:
Temperate climates every three years.
Hot climates every year.
RENEW CAMSHAFT DRIVE BELT - Tdi
Renew camshaft drive belt.See ENGINE, Repair,
Camshaft Drive Belt and Gears
The engine timing gears are driven by a flexible
rubber belt which must be renewed at intervals
determined by the severity of operating conditions.
In reasonable, temperate climate operation, renew the
belt every 120,000 km (72,000 miles) or every 6 years
whichever occurs earlier.
In adverse operating conditions such as work in dusty
atmospheres, high ambient temperatures and desert
and tropical zones, renew the belt every 60,000 km
(36,000 miles) or every 3 years whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious damage.
RENEW CAMSHAFT DRIVE BELT - Mpi
Renew every 160,000 km (96,000 miles) or every 6
years. In adverse conditions every 80,000 km (48,000
miles).
For details of renewing camshaft drive belt.
See
ENGINE, Repair, Camshaft Drive Belt - Mpi
CHECK CAMSHAFT DRIVE BELT - Mpi
For details of checking camshaft drive belt.See
ENGINE, Repair, Check Camshaft Drive Belt - Mpi

10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

Tdi
23
REPAIR VACUUM PUMP
Service repair no - 70.50.19
Remove
NOTE: To ease pump removal set engine
to T.D.C. on No.1 cylinder.
1.Disconnect battery negative lead.
2.Detach servo hose from vacuum pump.
3.Remove six bolts securing vacuum pump.
4.Detach pump complete with harness bracket.
Note location of bracket for refitting.
Refit
5.Clean mating faces of pump and block.
6.Loosely assemble pump to block with a new
gasket and with harness bracket located under
head of bolt noted during removal.
7.Evenly tighten bolts, to depress pump plunger,
finally tightening to
25 Nm.
8.Connect vacuum hose and secure with clip.
9.Reconnect battery negative lead.GENERATOR
Service repair no - 86.10.02
Remove
1.Disconnect battery negative lead.
2.Remove drive belt.
See Drive Belt Renew
3.Disconnect electrical leads from rear of
generator.
4.Remove securing bolt from bottom of generator.
5.Remove long through bolt from top fixing and
withdraw generator.
Refit
6.Reverse removal procedure.

12ENGINE
2
SPECIFICATIONS, TORQUECylinder head
Cylinder head to cylinder block See repair section......................................................
Stub pipe heater feed 22.................................................................................
Water temperature sensor 14.........................................................................
Blanking plug cylinder head 14.......................................................................
Engine lifting brackets 25................................................................................
Electrical harness clip bracket 25...................................................................
Exhaust manifold stud 10................................................................................
Exhaust manifold nut 45.................................................................................
Inlet manifold stud 8.......................................................................................
Inlet manifold nut and bolt 25..........................................................................
Air temperature sensor, inlet manifold 14.......................................................
Blanking plug, inlet manifold 14......................................................................
Heatshield to inlet manifold 6.........................................................................
Glow plug 20...................................................................................................
Glow plug terminal nut 2................................................................................
Injector clamp (stud) 8...................................................................................
Injector clamp (nut) 25....................................................................................
Thermostat housing 25...................................................................................
Water outlet elbow to thermostat housing 25..................................................
Water temperature switch, thermostat housing 11..........................................
Plug thermostat housing 6.............................................................................
Rocker shaft pedestal bolt 5 + 50° .....................................................................
Rocker cover (stud) 8.....................................................................................
Rocker cover (fixing nut) 10............................................................................
Breather cyclone to rocker cover 9................................................................
Tappet adjusting nut 16..................................................................................
Front cover to cylinder block 25......................................................................
Front cover plate to front cover 25..................................................................
Static idler - timing belt (stud) 10.....................................................................
Static idler - timing belt (nut) 45......................................................................
Tensioner (timing belt) 45...............................................................................
Camshaft hub bolt 80......................................................................................
Timing pulley to camshaft hub 25...................................................................
Fuel injection pump (stud) 8...........................................................................
Fuel injection pump (nut) 25...........................................................................
Abutment bracket to injection pump 25...........................................................
Support bracket injection pump to cylinder block 25.......................................
Fuel injection pump access plte to front cover plate 25..................................
Timing pulley to injection pump hub 25...........................................................
TV Damper pulley bolt to crankshaft 80 + 90° .....................................................
Fan pulley to hub 25.......................................................................................
Fan and viscous coupling to hub 45...............................................................
Auto tensioner, auxiliary drive (stud) 14..........................................................
Auto tensioner, auxiliary drive (nut) 45...........................................................
Auxiliary mounting bracket to cylinder block (stud) 8.....................................
Auxiliary mounting bracket to cylinder block (bolt and nut) 25........................
Water pump to block and mounting plate 25..................................................
Water pump pulley to hub 25..........................................................................

Tdi
3
SPECIFICATIONS, TORQUE Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Generator to auxiliaries mounting bracket 25.................................................
Starter motor (bolt and nut) 45........................................................................
Tachometer electrical connection 4...............................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................

V8i
3
FAULT DIAGNOSIS ENGINE STARTING PROBLEMS
Engine fails to crank in park or neutral (Automatic
Transmission)
1.Is battery in good state of charge?
NO -
See INTRODUCTION, Information,
Jump Starting
YES - Continue.
2.Is automatic transmission inhibitor switch faulty
or gear selection linkage incorrectly adjusted?
YES -
See AUTOMATIC GEARBOX, Repair,
Inhibitor Switch
,
NO -
See Electrical Trouble Shooting
Manual.
If problem is not diagnosed repeat tests, starting
at 1.
Engine fails to crank (Manual Transmission)
1.Is battery in good state of charge?
NO -
See INTRODUCTION, Information,
Jump Starting
YES -See Electrical Trouble Shooting
Manual.
If problem is not diagnosed repeat tests, starting
at 1.
Engine cranks but fails to start
1.Is the cranking speed fast enough (120 rpm)?
NO -
See INTRODUCTION, Information,
Jump Starting
If necessary also.See Electrical Trouble
Shooting Manual.
YES - Continue.
2.Is there combustion in any cylinder?
NO -
See ELECTRICAL, Fault diagnosis,
Lucas Constant Energy Ignition
System - V8i See Electrical Trouble
Shooting Manual.
YES - Continue.
3.Are the fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel pump and Sender Unit See
EMISSION CONTROL, Description and
operation, Emission control
If problem is not diagnosed repeat tests, starting
at 2.ENGINE RUNNING PROBLEMS
Engine runs at high speed but will not idle (stops)
Engine idle speed erratic Engine starts but stops
immediately
Engine stalls Engine misfires/hesitation
1.Multiport fuel injection.
See Electrical Trouble
Shooting Manual. See ELECTRICAL, Fault
diagnosis, Lucas Constant Energy Ignition
System - V8i
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
If problem is not diagnosed continue.
2.Are HT leads correctly routed and clipped?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit See
EMISSION CONTROL, Description and
operation, Emission Control
If problem is not diagnosed repeat tests, starting
at 1.
Engine lacks power/poor performance
1.Is throttle travel restricted or cable incorrectly
adjusted?
YES - Check thickness of carpets.
See FUEL
SYSTEM, Repair, Throttle Cable See
FUEL SYSTEM, Repair, Accelerator
Pedal
NO - Continue.
2.Are the Ignition and Multiport Fuel Injection
systems in order?
NO -
See Electrical Trouble Shooting
Manual.A1 See ELECTRICAL, Fault
diagnosis, Lucas Constant Energy
Ignition System - V8i See
ELECTRICAL, Repair, Distributor - V8i
YES - Continue.

12ENGINE
4
FAULT DIAGNOSIS 3.Are fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit
YES - Suspect valves held open by hydraulic
tappets due to high oil pressure.
See
Engine Oil Pressure Test
4.Is oil pressure high?
YES - Remove oil filter and cooler adaptor and
check pressure relief valve strainer gauze
for blockage and that the relief valve is
not stuck closed.
See Description and
operation, Description
NO - Carry out cylinder compression tests to
determine condition of head gaskets and
valves.
See Cylinder Compression -
Test
5.Are cylinder compressions satisfactory?
NO -
See Repair, Cylinder Heads - Renew
YES - Check brake vacuum connections.See
BRAKES, Description and operation,
Brake Servo Unit
Check heater/ventilation unit vacuum connections.
See HEATING AND VENTILATION, Description and
operation, Heating and Ventilation Unit
If problem is not diagnosed: Continue.
6.Are the brakes binding?
YES - Investigate cause of binding.
NO - Continue.
7.Automatic Transmission only. Is the Torque
Converter and Transmission operating correctly?
Carry out Road test, Static tests and Stall tests
to determine condition of Automatic
transmission.
If problem is not diagnosed: repeat tests starting at 1.Engine backfires into exhaust system
1.Are there any leaking joints/connections or holes
in the exhaust system?
YES -
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust System
Complete
NO - Continue.
2.Is distributor fitted correctly, HT leads in correct
firing order and routed correctly?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
4.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
See Repair, Cylinder Heads - Renew
If problem is not diagnosed: repeat tests starting
at 1.

V8i
5
FAULT DIAGNOSIS Engine backfires into inlet system
1.Is the Distributor, HT connections and routing
correct?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
2.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
3.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
For repairSee Repair, Cylinder Heads -
Renew
If problem is not diagnosed: repeat tests starting
at 1.

V8i
9
REPAIR FRONT COVER GASKET
Service repair no - 12.65.04
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys
2.Remove water pump pulley.
3.Release distributor cap clips.
4.Release plug leads from plugs and clips.
5.Place cap and leads to one side.
6.Turn engine until No. 1 piston is at T.D.C.
7.Check position of rotor arm.
8.Remove fixings securing power steering pump
bracket to water pump bracket.
9.Remove power steering pump bracket from
water pump.
10.Remove clips securing wiring to generator
tensioner.
11.Disconnect distributor feed wire.
12.Pivot power steering pump away from front
cover, tighten pivot to retain in position.
13.Disconnect vacuum pipe from distributor.
14.Remove water pump bottom hose.
15.Disconnect oil pressure switch.
16.Disconnect heater hose at water pump.
17.Remove generator tensioner from water pump,
move tensioner aside.
18.Mark distributor position to front cover.
19.Remove distributor clamp, remove distributor.
See ELECTRICAL, Repair, Distributor - V8i
20.Remove fixings sump to front cover.
21.Loosen four adjacent sump fixings.
22.Remove generator support strut from front cover,
move strut aside.
23.Loosen remaining front cover fixings and remove
front cover.
24.Remove front cover gasket.Refit
25.Clean timing cover, clean block face.
26.Lightly grease gasket faces.
27.Fit new gasket to block face.
28.Apply hylosil to sump gasket.
29.Clean threads of cover fixing bolts, apply Loctite
372 to threads.
30.Fit timing cover, fit fixing bolts. Tighten to
28
Nm.
31.Fit generator support strut to front cover.
32.Tighten sump to timing cover fixings to
10 Nm.
33.Tighten sump fixings to10 Nm.
34.Lubricate distributor O ring.
35.Fit distributor in position marked.
36.Align oil pump drive, if distributor does not seat
correctly.
37.Fit distributor clamp. Tighten to
20 Nm.
38.Locate generator tensioner on water pump
bracket.
39.Connect heater hose, tighten clip.
40.Connect oil pressure switch.
41.Connect bottom hose, tighten clip.
42.Connect vacuum pipe to distributor.
43.Loosen power steering pump pivot, lower pump.
44.Connect distributor feed wire.
45.Connect wire ties to generator tensioner.
46.Fit power steering pump bracket to water pump.
Tighten to
28 Nm.
47.Fit power steering pump to bracket.
48.Position distributor cap. Fit plug leads to plugs
and clips.
49.Clip distributor cap in position.
50.Fit water pump pulley. Tighten to
10 Nm.
51.Fit crankshaft pulley.See Crankshaft Pulley
Assembly
52.Tension drive belts correctly.
53.Check ignition timing.
54.Refill cooling system.