sensor LAND ROVER FREELANDER 2001 Workshop Manual

SECURITY
REPAIRS 86-4-3
Immobilisation - electronic control unit
(ECU) -
$% 86.77.07
Remove
1.Disconnect battery earth lead.
2.Remove fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
3.Remove 2 plastic nuts securing immobilisation
ECU and disconnect multiplug. Remove
immobilisation ECU.
Refit
1.Connect multiplug to immobilisation ECU.
2.Position ECU, fit and tighten 2 plastic nuts.
3.Fit fascia.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Fascia - up to 04MY.
4.Connect battery earth lead.
5.Initiate using TestBook/T4.
Sensor - volumetric - alarm system - 3
door
$% 86.77.29
Remove
1.Remove roof lamp lens.
2.Remove 2 screws, release roof lamp and
disconnect multiplug.
3.Release headlining rear finisher from roof panel
and remove finisher.
M86 5633

SECURITY
86-4-4 REPAIRS
4.Release door aperture seals to release
headlining.
5.Release 3 studs securing rear edge of
headlining to roof panel.
6.Remove 4 screws securing headlining to 'B'
posts.
7.Release 2 studs securing sides of headlining to
body.
8.Lower front edge of headlining.
9.Release sun roof seal.
10.Remove 2 screws from volumetric sensor.
11.Disconnect multiplug from volumetric sensor
and remove.Refit
1.Position volumetric sensor and connect
multiplug.
2.Fit sensor and secure with screws.
3.Fit headlining to 'B' posts and secure with
screws.
4.Secure headlining behind rear vent rubbers.
5.Fit headlining rear finisher.
6.Fit door aperture seals.
7.Fit headlining to sun roof seal.
8.Position roof lamp and connect multiplug.
9.Fit roof lamp and secure with screws.
10.Fit lens to roof lamp.

SECURITY
86-4-6 REPAIRS
8. Up to 04MY: Remove lens from front interior
lamp.
9. Up to 04MY: Remove 2 Torx screws securing
front interior lamp to body.
10. Up to 04MY: Release front interior lamp from
headlining, disconnect multiplug and remove
lamp.
11. From 04MY: Working from lamp forward edge,
release front interior lamp from headlining,
disconnect multiplug and remove lamp.12.Release LH 'B/C' post upper finisher.
13.Carefully lower headlining to gain access to
volumetric sensor.
14.Disconnect multiplug from volumetric sensor.
15.Remove 2 screws and remove sensor.

SECURITY
REPAIRS 86-4-7
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Raise headlining and secure with trim studs.
4. Up to 04MY: Position front interior lamp and
connect multiplug.
5. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
6. Up to 04MY: Fit lens to front interior lamp.
7. From 04MY: Position front interior lamp and
connect multiplug.
8. From 04MY: Fit and secure front interior lamp
to headlining.
9.Position 'B/C' post upper finisher and secure
with clips.
10.Fit sun visor.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
11.Fit grab handles, tighten screws and fit screw
covers.
12.Fit 'A' post upper finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
14.Secure front and rear door seals.
Module (ECU) - volumetric - alarm
system - 5 door - with sunroof
$% 86.77.29
Remove
1.Release front and rear door aperture seals.
2.Remove 'A' post upper finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
3.Remove screw covers, remove 6 screws
securing front and both rear grab handles and
remove grab handles.
4.Remove grab handle blanking plugs.

SECURITY
REPAIRS 86-4-9
12.Remove 2 trim studs securing centre of
headlining.
13.Release 8 clips securing both 'B/C' post upper
finishers and pull finishers clear of headlining.
14.Carefully lower headlining to gain access to
volumetric sensor.15.Disconnect multiplug from volumetric sensor.
16.Remove 2 screws securing volumetric sensor
and remove sensor.
Refit
1.Fit volumetric sensor and secure with screws.
2.Connect multiplug to sensor.
3.Secure the headlining with trim studs.
4.Position 'B/C' post upper finisher and secure
with clips.
5.Fit sun visors.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Sun visor.
6.Fit 'A' post upper finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
7.Fit grab handles, tighten screws and fit screw
covers.
8.Fit grab handle blanking plugs.
9. Up to 04MY: Position front interior lamp and
connect multiplug.
10. Up to 04MY: Fit Torx bolts securing interior
lamp and tighten to 6 Nm (4.4 lbf.ft).
11. Up to 04MY: Fit lens to front interior lamp.
12. From 04MY: Position front interior lamp and
connect multiplug.
13. From 04MY: Fit and secure front interior lamp
to headlining.
14.Position and secure sun roof finisher.
15.Secure front and rear door seals.

IN CAR ENTERTAINMENT
86-6-4 REPAIRS
Speaker - front
$% 86.50.15
Remove
1.Remove front door trim casing.

+ DOORS, REPAIRS, Trim casing -
front door - 3 door.

+ DOORS, REPAIRS, Trim casing -
front door - 5 door - up to 04MY.
2.Remove 4 screws securing speaker to front
door.
3.Disconnect multiplug from speaker and remove
speaker.
Refit
1.Position speaker to door and connect multiplug.
2.Fit speaker to door and secure with screws.
3.Fit front door trim casing.

+ DOORS, REPAIRS, Trim casing -
front door - 3 door.

+ DOORS, REPAIRS, Trim casing -
front door - 5 door - up to 04MY.
Aerial - manual - 3 door
$% 86.50.18
Remove
1.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
2.Remove 2 screws and release volumetric
sensor mounting bracket.
3.Remove nut securing coaxial cable to aerial
base.
4.Remove aerial base from roof panel and
remove rubber seal.
Refit
1.Position rubber seal and fit aerial base to roof
panel.
2.Connect coaxial cable and secure with nut.
3.Position volumetric sensor bracket and secure
with screws.
4.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.

HARNESSES
86-7-2 REPAIRS
Harness - main
$% 86.70.07
Remove
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove carpet.
3.Remove engine acoustic cover.

+ ENGINE - Td4, REPAIRS, Cover -
engine acoustic - Up to 02.5 Model Year.
4.Remove windscreen washer reservoir.

+ WIPERS AND WASHERS, REPAIRS,
Reservoir - washer.
5.Pull reservoir harness and washer tubes into
engine bay.
6.Remove nut and release earth header from RH
inner wing.
7.Disconnect multiplug from ABS modulator.
8.Disconnect multiplug from RH ABS speed
sensor and release harness from clips.
9.Disconnect 2 multiplugs from RH headlamp
and headlamp levelling motor.10.Disconnect multiplugs from horn, refrigerant
pressure sensor and compressor.
11.Remove jack from holder in engine bay.
12.Disconnect multiplug from brake fluid low level
indicator switch.
13.Disconnect multiplug from bonnet switch.
14.Remove bolt and 2 nuts securing PAS and
coolant reservoir support bracket and position
aside.
15.Release 5 harness retaining clips.
16.Release front screen wash tube from harness
and position aside.
17.Remove nut securing earth header to bulk head
and remove earth header.

HARNESSES
REPAIRS 86-7-3
18.With assistance feed harness through bulk
head into vehicle.
19.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
20.Remove 3 cable ties and release bonnet
release cable from harness.
21.Disconnect multiplug from cooling fan pack and
2 multiplugs from cooling fans.
22.Release 4 clips securing harness to cooling
fans and release harness from cooling fans.
23.Disconnect 2 multiplugs from LH headlamp and
headlamp levelling motor.
24.Disconnect multiplug from harness.25.Remove nut securing LH earth header and
release header.
26.Disconnect multiplug from front LH ABS speed
sensor.
27.Disconnect Lucar connector from starter motor.
28. Models with cruise control:Disconnect
multiplug from cruise control vacuum pump.
29.Release 5 harness retaining clips.
30.Disconnect 2 engine harness to main harness
multiplugs.
31.Release 5 Allen screws securing 'E' box cover
to 'E' box.
32.Remove 'E' box cover

HARNESSES
86-7-4 REPAIRS
33. Automatic gearbox only: Disconnect
multiplug from automatic gearbox ECU.
34.Disconnect 2 engine harness to main harness
multiplugs.
35.Disconnect 'E' box temperature sensor
multiplug.
36.Disconnect 'E' box cooling fan multiplug.
37.Remove fuse box cover.
38.Remove 2 bolts securing battery connections to
fuse box and disconnect multiplug from fuse
box.
39.Remove 3 nuts securing fuse box to brackets.40.Disconnect 6 multiplugs from the underside of
fusebox.
41.Disconnect multiplug from inertia switch.
42.Release 2 fixings securing harness to LH side
of engine bay.
43.Remove air intake plenum.

+ HEATING AND VENTILATION,
REPAIRS, Plenum - air intake.

HARNESSES
86-7-6 REPAIRS
53.Release fuse box, disconnect 11 multiplugs
and remove fuse box.
54.Disconnect multiplug from steering column
switch.
55.Release harness clip from steering column.
56.Disconnect multiplug from throttle position
sensor.
57.Disconnect multiplugs from brake light switch
and brake pedal position switch.58.Disconnect multiplug from airbag ECU.
59.Remove airbag ECU securing bolt and release
earth lead.
60.Remove nut from earth header and release
header from floor tunnel.