Lexus ES300h 2014 Navigation Manual

150
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
XU.S.A. XCanada
zFCC ID : BABFT0033A
z This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
CAUTION
●FCC WARNING
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s
authority to operate the equipment.
●CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with FCC
radiation exposure limits set forth for
uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at
least 20 cm and more between the
radiator and person’s body (excluding
extremities: hands, wrists, feet and
ankles).
●Co-location: This transmitter must not be
co-located or operated in conjunction
with any other antenna or transmitter.
zIC: 2024B-FT0033A
z This device complies with Industry
Canada licence-exempt RSS
standard(s). Operation is subject to the
following two conditions: (1) this device
may not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesired operation of the device.
z Le présent appareil est conforme aux
CNR d’Industrie Canada applicables
aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2)
l’utilisateur de l’ap pareil doit accepter
tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en
compromettre le fonctionnement.

151
1. PHONE OPERATION
4
PHONE
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
CAUTION
●CAUTION: Radio Frequency Radiation
Exposure
This equipment complies with IC
radiation exposure limits set forth for
uncontrolled equipment and meets RSS-
102 of the IC radio frequency (RF)
Exposure rules. This equipment has very
low levels of RF energy that it deemed to
comply without maximum permissive
exposure evaluation (MPE). But it is
desirable that it should be installed and
operated with at least 20 cm and more
between the radiator and person’s body
(excluding extremities: hands, wrists, feet
and ankles).
●ATTENTION : Exposition aux radiations
des fréquences radioélectriques
Cet équipement se conforme aux limites
d’exposition aux radiations établies par
Industrie Canada pour un environnement
non contrôlé ainsi qu’aux directives
d’exposition aux fréquences
radioélectriques (RF) émises par
Industrie Canada dans la norme
CNR-102. Cet équipement émet un
niveau d’énergie RF faible à un point tel
qu’il se conforme sans devoir effectuer
d’évaluation d’exposition maximum
admissible (MPE). Lorsque l’équipement
est installé et utilisé, il est toutefois
souhaitable de laisser au moins 20 cm
entre l’antenne et le corps (à l’exception
des extrémités : mains, poignets, pieds et
chevilles).
●This Category II radiocommunication
device complies with Industry Canada
Standard RSS-310.
●Ce dispositif de radiocommunication de
catégorie II respecte la norme CNR-310
d’Industrie Canada.

152
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3. REGISTER A Bluetooth® PHONE
1Press the “MENU” button on the
Remote Touch.
2Select “Phone” .
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
3Select “Yes” to register a phone.
zIf 5 Bluetooth® devices have already been
registered, a registered device needs to be
deleted. See “When 5 Bluetooth
® devices
have already been registered” on page
153.
4When this screen is displayed, operate
the Bluetooth
® device.
z Search for the navigation system displayed
on the system’s screen using your
Bluetooth
® device, and register the
Bluetooth® device.
For details about operating the Bluetooth®
device, see the manual that comes with it.
z A passcode is not required for SSP (Secure
Simple Pairing) compatible Bluetooth
®
phones. Depending on the type of
Bluetooth® phone being connected, a
message confirming registration may be
displayed on the Bluetooth
® phone’s
screen. Respond and operate the
Bluetooth
® phone according to the confir-
mation message.
To use the hands-free system, it is neces-
sary to register a phone with the system.
Once the phone has been registered, it
is possible to make a hands-free call.
If a Bluetooth
® phone has not been reg-
istered yet, it is necessary to register it
first according to the following proce-
dure. A Bluetooth
® phone cannot be
registered while driving.
z See “REGISTERING A Bluetooth®
DEVICE” on page 195 of additional reg-
istration when registering.

153
1. PHONE OPERATION
4
PHONE
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zTo cancel the registration, select “Cancel”.
z If the Bluetooth
® phone to be registered
has a Bluetooth® audio function, this can
be registered at the same time.
5This screen will be displayed when reg-
istration is complete.
z When using the same phone, it is not nec-
essary to register it again.
X When this screen is displayed, follow the
guidance on the screen to try again.
X When another Bluetooth
® device is con-
nected
z When another Bluetooth® device is cur-
rently connected, this screen is displayed.
z To disconnect the Bluetooth
® device,
select “Yes” .
XWhen 5 Bluetooth® devices have al-
ready been registered
1When 5 Bluetooth® devices have al-
ready been registered, a registered de-
vice needs to be deleted. Select “Yes” to
delete 1 or more.
2Select the device to be deleted, then se-
lect “Remove” .
3Select “Yes”.
X If the Bluetooth
® phone has a
Bluetooth® audio function
z When the Bluetooth® phone to be regis-
tered has a Bluetooth® audio function, this
audio function will be registered automati-
cally at the same time and this screen may
be displayed. If this screen is displayed,
select “Yes” to connect the audio function
or select “No” to cancel the connection.

154
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zFor automatic connection, see “CHANG-
ING “Bluetooth* Power”” on page 202.
z When the “START STOP ENGINE”
<“POWER”> switch is in ACCESSORY or
IGNITION ON <ON> mode, the system
searches for a nearby registered cellular
phone.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
z The system will connect with the phone that
was last connected, if it is nearby.
When “Display Phone Status” is set to
“On” , the connection status is displayed.
(See “Bluetooth
® DEVICE CONNEC-
TION STATUS DISPLAY SETTINGS” on
page 204.)
z This screen appears when the Bluetooth
®
phone is first connected after the “START
STOP ENGINE” <“POWER”> switch is in
ACCESSORY or IGNITION ON <ON>
mode.
CONNECTING A Bluetooth®
PHONE
AUTOMATICALLY
When a phone is registered, auto con-
nection is turned on. Always set it to this
mode and leave the Bluetooth
® phone
in a location where connection can be
established.
INFORMATION
●
It may take time if the phone connection
is carried out during Bluetooth® device
playback.
Depending on the type of Bluetooth
®
phone being connected, it may be neces-
sary to perform additional steps on the
phone.

155
1. PHONE OPERATION
4
PHONE
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch, then select “Phone”.
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
2Select “Connect Phone” .
3Select the screen bu tton corresponding
to the desired phone connection.
z When the cellular phone’s device name has
not been able to be obtained, “Device 1” to
“Device 5” will be displayed in the order the
phones were registered.
*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
4This screen is displayed.
5When the connection is completed, this
screen is displayed.
z Now you can use the Bluetooth® phone.
X When a phone is connected while
Bluetooth® audio is playing
zThis screen is displayed, and the
Bluetooth® audio will stop temporarily.
MANUALLY
When the auto connection has failed or
“Bluetooth* Power” is turned off, it is
necessary to connect Bluetooth
® man-
ually.

156
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zIf a Bluetooth® phone is disconnected on
purpose, such as turning it off, this does not
happen. Reconnect the Bluetooth
® phone
manually.
RECONNECTING THE
Bluetooth® PHONE
If a Bluetooth® phone is disconnected
due to poor reception from the
Bluetooth
® network when the “START
STOP ENGINE” <“POWER”> switch is
in ACCESSORY or IGNITION ON
<ON> mode, the system automatically
reconnects the Bluetooth
® phone.
When “Display Phone Status” is set to
“On” , the connection status is displayed.

157
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4
PHONE
4. CALL ON THE Bluetooth® PHONE
1Press the “MENU” button on the
Remote Touch. (See “Remote Touch”
on page 10.)
2Select “Phone” on the “Menu” screen.
zThe “Phone” screen can be displayed by
pressing
on the steering wheel.
3Select the desired keys to input the
phone number.
zEach time is select ed, an input digit is
deleted.
4Select or press the switch on
the steering wheel.
z Depending on the type of Bluetooth®
phone being connected, it may be neces-
sary to perform additional steps on the
phone.
1Select “Contacts” .
2Select the desired data from the list.
After a Bluetooth® phone has been reg-
istered, a call can be made using the
hands-free system. There are 7 methods
by which a call can be made. These are
described below.
BY DIAL
A call can be made by inputting the
phone number.
This cannot be operated while driving.
BY PHONEBOOK
Calls can be made by using the phone-
book data which is transferred from the
registered cellular phone.
The phonebook changes depending on
the phone connected. Up to 1000 con-
tacts (maximum of 3 numbers per con-
tact) can be regi stered in each
phonebook.
This cannot be operated while driving.

158
1. PHONE OPERATION
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3Select the desired number from the list.
4Select or press the switch on
the steering wheel.
1Select “Contacts” .
2Select “Yes” or “Transfer” to automati-
cally transfer the phonebook from the
connected phone.
z Select “Manual” to transfer the phonebook
manually. (See “TRANSFERRING A
PHONE NUMBER” on page 175.)
z Select “No” or “Cancel” to cancel transfer-
ring.
z If your cellular phone is neither PBAP nor
OPP compatible, the phonebook cannot
be transferred.
X PBAP compatible models
X PBAP incompatible but OPP compatible
models
3Transfer the phonebook data to the sys-
tem using the Bluetooth
® phone.
zDepending on the type of cellular phone,
OBEX authentication may be required
when transferring phonebook data. Enter
“1234” into the Bluetooth
® phone.
z This screen appears while transferring. To
cancel this function, select “Cancel” .
WHEN THE PHONEBOOK IS
EMPTY

159
1. PHONE OPERATION
4
PHONE
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
4When the data transfer from a PBAP in-
compatible but OPP compatible model
is complete, “Done” will appear on the
screen. Select “Done”.1Select “Speed Dials” .
2Select the desired number to call.
zThe list to be displayed can be changed by
selecting the “Speed Dial 1” , “Speed Dial
2” or “Speed Dial 3” tab.
INFORMATION
●
Depending on the type of Bluetooth®
phone:
• It may be necessary to perform addi- tional steps on the phone when transfer-
ring phonebook data.
• The registered image on the phone- book may not appe ar when phonebook
data is transferred.
BY SPEED DIAL
Calls can be made using registered
phone numbers which can be selected
from a phonebook. (See “REGISTER-
ING THE SPEED DIAL” on page 183
for registering the speed dial.)
This can be operated while driving.