LEXUS LS430 2005 Owners Manual

Page 241 of 539

OCCUPANT RESTRAINT SYSTEMS
222Conditions for memorized position activation

Ignition switch “ON” and selector lever in “N” or “P” position
with the vehicle stopped.
All parts of the memorized positions can be activated.
 Ignition switch off and within 30 seconds of opening driver’s
door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY CALL SYSTEM USING A SMART KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized position when you open the driver’s door after
unlocking it with a smart key. And when you push the
ignition switch, the tilt and telescopic steering is adjusted.
To activate this system, the ID of the smart key needs to
be registered in the memory button.
Registering the smart key ID code
Before the registration of the ID of the smart key, the driving
position must be memorized in the memory button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the smart key in possession, select a button in
which you want to record the ID of the key from buttons
“1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with button “1”, “2” or “3” held\
down.
When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered in another button, that memory will also be erased.

Page 242 of 539

OCCUPANT RESTRAINT SYSTEMS
223
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the smart key in which you want to cancel the
registration in possession and push the “SET” button.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with the “SET” button held
down.
When the previous key ID memory is erased, two beeps
sound.MEMORY CALL SYSTEM USING A WIRELESS REMOTE
CONTROL KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized
position when you open the driver’s door after
unlocking it with a wireless remote control key. And when
you insert the key into the ignition switch, the tilt and
telescopic steering is adjusted.
To activate this system, the ID of the wireless remote
control key ne eds to be registered in the memory button.
Registering the wireless remote control key
ID code
Before the registration of the ID of the wireless remote control
key, the driving position must be memorized in the memory
button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the wireless remote control key in possession,
select a button in which you want to record the ID of the
key from buttons “1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with button “1”,
“2” or “3” held down.

Page 243 of 539

OCCUPANT RESTRAINT SYSTEMS
224When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered
in another button, that memory will also be erased.
CAUTION
Do not push the “LOCK” button any longer than 2 or 3
seconds. Pushing the button longer activates an alarm.
For details, see page 40.
Erasing the previous registration memory
The driver’s door must be closed with the ignition switch in the
“OFF” position.
1. Keep the wireless remote control key in which you want
to cancel the registrati on in possession and push the
“SET” button.
2. Push the “LOCK” or “UNLOCK” button on the wireless
remote control key for about one second with the “SET”
button held down.
When the previous key ID memory is erased, two beeps
sound.
REAR SEAT POSITION MEMORY SYSTEM
A microcomputer will memorize the position of the rear seats
and the height of the rear head restraints.
Recording the rear seat position in the computer’s memory can
only be done when the ignition switch is in the “ON” position.
Setting the rear seat position
16L301a
1. Adjust the rear seat position and the height of the head
restraint of the rear seat to the desired position.
2. Keep pushing the “SET” button until a beep sounds.
The beep sound means that the position has been memorized.
The memory will be erased when the battery is removed for
inspection or service.

Page 244 of 539

OCCUPANT RESTRAINT SYSTEMS
225
Recalling the memorized position
16L302a
Keep pressing the “M” button until a beep sounds; the
rear seat and rear head restraint positions will be
automatically adjusted to the memorized position.
If the “M” switch is pushed while the memorized position profile
is being activated, the operation will stop.
Do not place anything under the rear seat as this might
interfere with seat movement.
Door opening linked seat sliding function
The rear seat automatically moves backward when the
rear door is opened if the seat is adjusted to a forward
position.
The ignition switch must be in the “ON” position.
This function is actuated when the selector lever is set in the
“P” position or if the vehicle is stopped with the brake pedal
depressed.
While the seat is being moved by this function, the operation
will not stop even if the door is closed midway.
16L328a
To cancel this function, push the “C” button.
The indicator light comes on.

Page 245 of 539

OCCUPANT RESTRAINT SYSTEMS
226To reactivate the function once again, push the “C”
button.
The indicator light goes off.

Page 246 of 539

SECTION 1 – 7
227
INSTRUMENTS AND CONTROLS150.
Steering wheel and mirrors
Tilt and telescopic steering column228
. . . . . . . . . . . . . . . . . . . . . . . . .
Outside rear view mirrors 230
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside rear view mirror 234
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vanity mirrors 235
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .\
. . . . . .

Page 247 of 539

STEERING WHEEL AND MIRRORS
228
151.TILT AND TELESCOPICSTEERING COLUMN
Adjustment of steering column tilt
16L646
To adjust the tilt of the steering column, push the control
switch upward or downward to set it to the desired
position.
CAUTION
Do not adjust the steering column while the vehicle is
moving. Doing so may cause the driver to mishandle
the vehicle and an accident may occur resulting in death
or serious injuries.
Adjustment of telescopic steering column
16L647
To adjust the steering column length, push the control
switch forward or backward to set the steering wheel to
the desired position.
CAUTION
Do not adjust the steering column while the vehicle is
moving. Doing so may cause the driver to mishandle
the vehicle and an accident may occur resulting in death
or serious injuries.

Page 248 of 539

STEERING WHEEL AND MIRRORS
229
Automatic tiltaway*
In case of the smart key system:
16L644
When the smart key system is used, turning the ignition
switch
1 to the “LOCK” position moves the steering
column forward away from the driver and also tilts it up for
easy exit and entry.
When you push in the ignition switch, the steering column
returns to the previously set position.
NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details. When the key is inserted into the ignition:
16L715
When you remove the smart key 2
or ignition key 3,
the steering column moves forward away from the driver
and also tilts up for easy exit and entry.
When you insert the key in the ignition switch, the steering
column returns to the previously set position.
NOTE:
* This feature can be deactivated.
Ask your Lexus dealer for details.

Page 249 of 539

STEERING WHEEL AND MIRRORS
230
152.OUTSIDE REAR VIEWMIRRORS
16L282
Adjust the mirror so that you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side
because it is a convex mirror. Any object seen in a convex
mirror will look smaller and farther away than if seen in a normal
flat mirror.
When the inside rear view mirror darkens in “AUTO” mode, the
outside rear view mirrors also darken to reduce the reflection
of the headlights of the following vehicle. For details, see
“Inside rear view mirror” on page 234. When you push the rear window and outside rear view mirror
defogger swi
tch or operate the wipers, the heater panels in the
outside rear view mirrors will quickly clear the mirror surface.
(See “Windshield wiper and washer switch” on page 58 and
“Rear window and outside rear view mirror defogger switch” on
page 63.)
CAUTION
 Do not adjust the mirror while the vehicle is moving.
Doing so may cause the driver to mishandle the
vehicle and an accident may occur resulting in death
or serious injuries.
 Since the mirror surfaces can get hot, do not touch
them when the rear window and outside rear view
mirror defogger switch is on.

Page 250 of 539

STEERING WHEEL AND MIRRORS
231
Power rear view mirror control153.
16L641
 1Master switch 2Control switch
To adjust the power rear view mirror, first place the master
switch at “L” (left) or “R” (right), and push the contro\
l
switch on the desired side.
The power rear view mirrors can be adjusted when the ignition
switch is in the “ACC” or “ON” position. When you are backing up,
you can adjust the mirrors
down quickly by the following operations with the ignition
ON.
 Put the selector lever in the “R” position.
 Place the master switch at “L” (left) or “R” (right).
The mirrors return to the previous position by any of the
following operations.
 Put the selector lever in a position other than “R”.
 Place the master switch in the neutral position.
 Turn the ignition switch to the “ACC” position.NOTICE
If ice should jam the mirror, do not operate the control
or scrape the mirror face. Use a spray deicer to free the
mirror.

Page:   < prev 1-10 ... 201-210 211-220 221-230 231-240 241-250 251-260 261-270 271-280 281-290 ... 540 next >