radiator cap MAZDA 626 1987 User Guide

TROUBLESHOOTING GUIDE
3B

SPECIFICATIONS

Cooling system Water-cooled, forced circulation
Coolant capacity liters (US
qt,
Imp
qt)

With heater 9.5 (10.0, 8.4) Coolant capacity liters (US
qt,
Imp
qt)

Without heater 9.0 (9.5, 7.9)
Water pump Type Centrifugal, timing belt driven Water pump
Water seal Unified mechanical seal
Thermostat
Type Wax, two stage
Thermostat
Opening temperature °C(°F) Main Sub
Thermostat
Opening temperature °C(°F)
86.5-89.5 (188-193) 78.5—81.5 (173-179) Thermostat
Full-open temperature °C(°F) 100 (212) 100 (212)
Thermostat
Full-open lift
mm (in)
8.0 (0.31) min. 1.5 (0.06) min.
Radiator
Type Corrugated
fin

Radiator Cap valve opening pressure
kPa (kg/cm2,
psi)
74-103 (0.75-1.05, 11—15)
Cooling
fan

Type Electric
Cooling
fan

Capacity
W
120
Cooling
fan
Switching temprature orvopi OFF
- ON ^
91 (196) Cooling
fan

Number
of
blade 4
Cooling
fan

Outer diameter
mm
(in) 340 (13.4)

76G03B-003
TROUBLESHOOTING GUIDE
Problem Possible Cause Remedy Page
Overheating
Insufficient coolant Add 3B-
4

Coolant leakage Repair
—

Radiator fins clogged Clean 3B—
6

Radiator cap malfunction Replace 3B—
5

Cooling fan malfunction Repair 3B-11 Thermostat malfunction Replace 3B—
9

Water passage clogged Clean 3B—
4

Water pump malfunction ReDair
or
replace 3B—
7

Corrosion
Impurities
in
coolant Replace 3B-
4

76G03B-004
3B—3

3B COOLANT
86U03X-004
69G03A-006
COOLANT
INSPECTION
Coolant Level (Engine cold)
1. Check that the coolant level is near the radiator inlet
port.
2. Check that the coolant level in the coolant reser-
voir is between the FULL and Low marks.
Add coolant if necessary.
Warning
a) Never remove the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
removing it.
Coolant Quality
1. Check that there is no build-up of rust or scales
around the radiator cap or radiator filler neck.
2. Check that coolant is free from oil.
3. Replace the coolant, if necessary.
Coolant Leakage
1. Connect a tester and SST to the radiator inlet port.
2. Apply 103 kPa (1.05 kg/cm2, 15 psi) pressure
to the system.
3. Check that the pressure is held.
If not, check for coolant leakage.
Warning
When removing either the radiator cap or the
tester, loosen it slowly until the pressure in
the radiator is released, and then remove it.
86U03X-005
REPLACEMENT
1. Remove the radiator cap and loosen the drain plug.
2. Drain the coolant into a suitable container.
Warning
a) Never open the radiator cap while the en-
gine is hot.
b)Wrap a thick cloth around the cap when
loosening.
c) Use caution when draining hot coolant.
86U03X-006
3B—4

RADIATOR CAP 3B
86U03X-028
86U03X-007
86U03X-008
3. Set the heater control switch to the maximum heat
position.
4. Flush the cooling system with water until all traces
of color are gone, then let the system drain com-
pletely.
5. Fill with the proper mixture and amount of ethy-
lene glycol-based coolant.
Caution
a) Do not use alcohol- or methanol-based
coolant.
b) Use only soft (demineralized) water in the
coolant mixture.
Anti-freeze solution mixture percentage

Protection Volume percentage Gravity
at

20°C (68°F) Protection Solution Water
Gravity
at

20°C (68°F)
Above —16°C (3°F) 35 65 1.054
Above -26°C (-15°F) 45 55 1.066
Above -40°C (-40°F) 55 45 1.078

6. Run the engine at idle with the radiator cap re-
moved. Let any air bleed from the system, and add
more coolant.
7. Install the radiator cap, and inspect all connections
for leakage.
RADIATOR CAP
INSPECTION
Radiator Cap Valve
1. Remove foreign material (such as water residue)
from between the radiator cap valve and the valve
seat.
2. Attach the radiator cap to a tester with the SST.
Apply pressure gradually to 74—103 kPa
(0.75—1.05 kg/cm2, 11—15 psi).
3. Wait about 10 seconds; then check that the pres-
sure has not decreased.
Negative Pressure Valve
1. Pull the negative-pressure valve to open it. Check
that it closes completely when released.
2. Check for damage on the contact surfaces, and
for cracked or deformed seal packing.
3. Replace the radiator cap if necessary.
86U03X-009
3B-5

30 TECHNICAL DATA
3A. COOLING SYSTEM (GASOLINE)
Engine model F6, F8, FE SOHC
Item FE DOHC ECE, Hong Kong
Singapore Middle East General

Cooling method Water-cooled, forced circulation

Water pump

Type Centrifugal, timing belt driven
Impeller diameter mm (in) 70 (2.76)
Number
of
impeller blades 6
Speed ratio 1
:
1.00 1
:
1.05
Water seal type Unified mechanical seal

Thermostat

Type Wax, 2-stage Wax
Start
to
open °C (°F) Sub: 83.5-86.5 (182-188) Main: 86.5-89.5 (188-193) 86.5-89.5 (188-193) 80.5-83.5 (177-182)
Full open °C (°F) 100 (212) 95 (203)
Lift mm (in) Sub: 1.5 (0.06) min.
Main: 8.0 (0.31) min. 8.5 (0.33) min.

Radiator

Type Corrugated
fin

Cap opening valve pressure kPa (kg/cm2,
psi)
74-103 (0.75-1.05,
11
-15)
Cooling system pressure kPa (kg/cm2,
psi)
103 (1.05,
15)
Cooling fan

Type Electric
Capacity W MTX 80 Capacity W ATX 120
Current A MTX 5
6 7.6
Current A ATX
—
8.0-11.0
Number
of
blades 4
Outer diameter mm (in) MTX 320 (12.6) Outer diameter mm (in) ATX 340 (13.4)
Switching temperature OFF -
ON
°C(°F) 97 (207) 91 (196)

Coolant

Capacity liters (US qt, Imp
qt)
With heater 7.5 (7.9, 6.6) Capacity liters (US qt, Imp
qt)
Without heater 7.0 (7.4, 6.2)
Protection Mixture percentage (volume)
%
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution
Protection Water Solution
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution Above -16°C (3°F) 65 35 1.054
Above -26°C (-15°F) 55 45 1.066
Above -40 °C (—40°F) 45 55 1.078

30-16

TECHNICAL DATA 30
3B. COOLING SYSTEM (DIESEL)
Item Engine model RF-CX, RF-N

Cooling method Water-cooled, forced circulation

Water pump

Type Centrifugal, timing belt driven
Water seal type Unified mechanical seal

Thermostat

Type Wax, two stage
Start
to
open °C (°F) Main valve:
86.5-89.5 (188-193)
78.5-
Sub valve: 81.5 (173-179)
Full open lift mm (in)/°C (°F) Main valve: 8.0 (0.31) Sub valve: 1.5 (0.06) min./100 (212) min./100 (212)

Radiator

Type Corrugated
fin

Cap opening valve pressure kPa (kg/cm2,
psi)
74—103 (0.75—1.05,
11
-15)
Cooling circuit checking pressure kPa (kg/cm2,
psi)
103 (1.05,
15)
Cooling fan

Type Electric
Number
of
blade 4
Outer diameter mm (in) 340 (13.4)
Switching temperature OFF -»
ON
°C (°F) 91 (196)
Voltage V 12
Capacity W-A 120-8.0-11.0

Coolant

Capacity liters (US qt, Imp
qt)
With heater 9.5 (10.0, 8.4) Capacity liters (US qt, Imp
qt)
Without heater 9.0 (9.5, 7.9)
Protection Mixture percentage (Volume) Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution
Protection Water Solution
Specific gravity
of
mixture
at
20°C (68 °F) Antifreeze solution Above -16°C (3°F) 65 35 1.054
Above -26°C (-15°F) 55 45 1.066
Above -40°C (-40°F) 45 55 1.078

30-17

30 TECHNICAL DATA
4B. FUEL AND EMISSION CONTROL SYSTEMS (FUEL INJECTION FE)
Item Specifications

Fuel tank capacity Liters (US gal, Imp gal) 60 (15.9, 13.2)
Fuel pump
Type In-tank, electric motor
Fuel pump Fuel pressure kPa (kg/cm2, psi) 441-588 (4.5-6.0, 64-85) Fuel pump
Feeding capacity cc (cu in)/10 sec. 220 (13.4) min.
Air cleaner Element type Oil permeated
Accelerator cable Deflection
mm
(in) 1—3 (0.04-0.12)
Idle speed
rpm
ATX: 800 +58 (Neutral), ATX: 900 +600
(P
range)
Dash
pot
Adjustment speed
rpm
1,900-2.100
EGR control valve Starts
to
open mmHg (in Hg) 40-60 (1.6-2.4)
Air control valve Starts
to
open mmHg (in Hg) 180-280 (7.1-11)
Water thermo valve Opened
°C
(°F) Higher than 46—54 (115-129)
Water thermo switch Opened
At
radiator
°C
(°F) Lower than 15—19 (59—66)
Vacuum switch valve Starts to open mmHg (in Hg) 66—106 (2.6—4.2)
Water thermo sensor Resistance
-20°C (-4°F)k!) 14.5-17.8
Water thermo sensor Resistance 20°C (68°F)
kQ
2.2-2.7 Water thermo sensor Resistance
80°C (176°F)k!i 0.28-0.35
Throttle sensor
Resistance
at

fully closed
B
C kQ
4-6
Throttle sensor
Resistance
at

fully closed A
« B Q
Approx.
500

Throttle sensor Resistance
at
fully opened A
«• B kQ
Approx.
4.5
Throttle sensor
Setting Closed at mm (in) 0.4 (0.0157)
Throttle sensor
Setting Open at mm (in) 0.55 (0.022)
Air flow meter
Resistance
of

full closed

E2 « Vs fi
More than
20

Air flow meter
Resistance
of

full closed

E2 •+ Vc 0
100-300
Air flow meter
Resistance
of

full closed
E2 VB Q
200-400 Air flow meter
Resistance
of

full closed
Ei
•+ Fc Q OO
Air flow meter
Resistance
at
full open Ei
•+ Fc Q
0
Intake
air
thermo sensor Resistance
-20°C M°RkQ 13.6-18.4
Intake
air
thermo sensor Resistance 20°C (68°F) kfi 2.21—2.69 Intake
air
thermo sensor Resistance
60°C (140°RkQ 0.493-0.667
Pressure regulator Regulating pressure At idling kPa
(kg/cm
,
psi) 235-275 (2.4—2.8, 34-40)
Injector
Injection amount cc (cu in)/15 sec. 38-53 (2.3-3.2) Injector
Resistance
Q
12-16
Circuit opening relay Resistance STA Ei Q 15-30 Circuit opening relay Resistance B
Fc fi
80-150
Fuel Unleaded gasoline

30-20

SPECIAL TOOLS 40
ENGINE
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 0107 680A
Engine stand A

V
ir==JJ
i

49 0636 100A
Arm, valve
spring lifter
A \JL
JL

49 0223 105B
Lifter, valve spring
(F6, F8, FE-2V)

A

49 G030 040
Tool set,
pis-
ton pin setting (F6,
F8,
FE SOHC)
A
49 E301
060

Brake, ring
gear
A

J

49 H011 101A
Lock tool,
crankshaft
A
ft
im

49 0636
145

Puller,
fan
puller boss A
49 S120 710
Holder, coupling
flange
A

TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 G030 005A
Hanger, engine stand A

|i
l\fy ^

49 G030 222
Pivot, valve spring lifter (F6,
F8,
FE SOHC)
A
r
o

49 0249 01 OA
Remover
&
installer, valve guide (FE-3V)
A
49 0249 01 OA
Remover
&
installer, valve guide (FE-3V)
A
c ii&zm

49 0249 01 OA
Remover
&
installer, valve guide (FE-3V)
A
49 1285 071
Puller bearing A
49 0221 251A
Remove
&

installer, valve
guide (F6,
F8,

FE-2V)
A
cr-

49 G030
160

Pusher, valve
seal (F6,
F8,

FE-2V)
A

if !

49 9200
146

Radiator cap tester adaptor set
A
49 B012 005
Remover and installer valve guide
(FE DOHC)
A

40—3

40 SPECIAL TOOLS
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 S120 220
Holder, tappet
(Disel)
A
49 0636 165A
Remover
&

installer,
valve guide
(Diesel)
A i
1 vrn

49 0223
061

Remover
&,
installer, piston pin (RF-N, FE DOHC)
B
49 S120 215A
Pulley puller (Diesel)
A
49 V101 060A
Brake,
ring gear
(Diesel)
A
49 S120 222
Pivot, valve spring lifter (RF-N, RF-CX, FE DOHC)
A
49 G011
101

Lock tool, crankshaft (RF-N, RF-CX)
A
49 H012 009
Pusher, valve
seal
(FE-3V)
A

40-4
TOOL NUMBER & DESCRIPTION PRIORITY ILLUSTRATION

49 9200
147

Radiator cap tester adaptor set
A
49 S120 170
Remover, valve seal (RF-N, RF-CX, FE DOHC)
A
49 0552
165

Remover
&
installer, valve guide (Diesel)
A D
<-—j
nm

49 S120 105
Compressor, valve spring (Diesel)
A

S-tSfe
49 S120 105
Compressor, valve spring (Diesel)
A
49 S120 160
Pusher, valve
seal
(Diesel)
A
49 G012 001
Collar (FE DOHC) A
( 4

49 G012 002
Pusher, valve seal (FE DOHC)
A
49 G011
001

Replacer,
piston
pin

(RF-CX)
A