MAZDA MODEL CX-30 2019 Owners Manual (in English)

Request Indication on display
Shift up Shift Up to a Higher Gear
Shift down Shift Down to a Lower Gear
NOTE
xIf the gears are not shifted up even
though the shift-up request
indication is displayed, load will be
applied to the engine and the CTS
might be automatically cancelled or
engine damage could occur.
xIf the gears are not shifted down
even though the shift-down request
indication is displayed, the CTS
might be automatically cancelled or
engine stalling could occur.
▼Stop Hold Control (Automatic
Transmission)
While in headway control using the
CTS, your vehicle will stop when a
vehicle ahead stops. When the vehicle
is stopped and the stop hold control
operates, the CTS indicator light turns
on.
NOTE
xEven if the CTS is temporarily
cancelled during stop hold control,
the vehicle is held in its stopped
position.
xThe parking brake is automatically
applied and the vehicle is held in its
stopped position when 10 minutes
or longer have passed since the stop
hold control operated. When this
occurs, the CTS is temporarily
cancelled.
xIf the i-stop operation conditions are
met during stop hold control, the
engine stops even though the brake
pedal is not depressed.
Refer to i-stop on page 4-11.
xThe brake lights turn on during stop
hold control.

To resume driving
After the vehicle ahead starts moving
while your vehicle is stopped under
stop hold control, press the RES switch
or depress the accelerator pedal to
cancel the stop hold control and start
driving.
NOTE
xWhen you resume driving by pressing
the RES switch, your vehicle does not
start moving until the distance
between your vehicle and the vehicle
ahead lengthens to the
specified
distance or farther.
xThe engine restarts automatically
when any of the actions to resume
driving are performed while i-stop is
operating.
xIf the CTS is temporarily cancelled
during stop hold control, you cannot
resume driving by pressing the RES
switch when there are no vehicles in
front of your vehicle. Depress the
accelerator pedal and resume driving
the vehicle.
When Driving
i-ACTIVSENSE
4-161

xIf the vehicle ahead starts moving
within 3 seconds after your vehicle is
stopped by the stop hold control,
headway control will continue even if
you do not resume driving your
vehicle, such as by depressing the
accelerator pedal.

Vehicle departure information
If you do not resume driving within a
few seconds after the vehicle ahead
starts moving during stop hold control,
the multi-information display
vehicle-ahead indication flashes to
urge the driver to resume driving. If you
do not resume driving after the
indicator light
flashes, a sound is
activated to urge you to resume
driving.
Lane-keep Assist System
(LAS)
*
▼Lane-keep Assist System (LAS)
The LAS provides steering assistance to
help the driver stay within the vehicle
lane if the vehicle might be deviating.
The forward sensing camera (FSC)
detects the white lines (yellow lines) of
the vehicle lane in which the vehicle is
travelling and if the system determines
that the vehicle may deviate from its
lane, it operates the electric power
steering to assist the driver’s steering
operation. The system also alerts the
driver by displaying an alert on the
multi-information display and the
active driving display. Use the system
when you drive the vehicle on roads
with white (yellow) lines such as
expressways and highways.
1. Forward sensing camera (FSC)
WARNING
Do not rely completely on the LAS:
¾The LAS is not an automated driving
system. In addition, the system is not
designed to compensate for a
driver’s lack of caution, and
over-reliance on the system could
lead to an accident.
When Driving
i-ACTIVSENSE
4-162*Some models.

¾The functions of the LAS have
limitations. Always stay on course
using the steering wheel and drive
with care.
¾Do not use the LAS under the
following circumstances, otherwise it
may result in an accident.
¾The vehicle is driven on slippery
roads such as icy or snow-covered
roads, and unpaved roads.
¾Tyres of a
different
specified size
are used, such as a temporary
spare tyre.
¾Tyres with
insufficient tread are
used.
¾The tyre pressures are not adjusted
to the
specified pressure.
¾The vehicle is being used to tow a
camper or boat trailer.
¾Tyre chains are used.
¾The vehicle is driven on roads with
lane lines other than white (yellow)
lines, such as an expressway.
CAUTION
Heed the following cautions so that
the LAS can operate normally.
¾Do not modify the vehicle's
suspensions.
¾Always use tyres of the specified type
and size for the front and rear
wheels. Consult an expert repairer
(we recommend an Authorised
Mazda Repairer) for tyre
replacement.
NOTE
The system may not operate normally
under the following conditions.
xThe white (yellow) lane lines are less
visible because of dirt or paint
flaking.
xWhite (yellow) lane lines are less
visible because of bad weather (rain,
fog, or snow).
xThe vehicle is driven on a temporary
lane or section with a closed lane
resulting from construction where
there might be multiple white
(yellow) lane lines, or they are
interrupted.
xThe camera picks up an obscure line,
such as a temporary line being used
for construction, or because of
shade, unmelted snow, or grooves
filled with water.
xThe surrounding brightness suddenly
changes such as when entering or
exiting a tunnel.
xBack-light is reflected off the road
surface.
xThe road surface is wet and shiny
after rain, or there are puddles on
the road.
xThe width of a lane is excessively
narrow.
xThe vehicle is driven on roads with
tight curves.
xHeavy luggage is loaded in the
luggage compartment or on the rear
seat causing the vehicle to tilt.
xThe vehicle is driven through a fork in
the road or a junction.
xThe shade of a guardrail parallel to a
white (yellow) lane line is cast on the
road.
xThe illumination of the headlights is
weakened because of dirt or the
optical axis is deviated at night.
xThe road is excessively uneven.xThe vehicle is shaken after hitting a
road bump.
xA vehicle in front of your vehicle is
running near a white (yellow) lane
line making it less visible.
xThe windscreen is dirty or foggy.
When Driving
i-ACTIVSENSE
4-163

xStrong light is directed from the front
of the vehicle (such as sunlight, or
headlights (high-beam) of
on-coming vehicles).
▼System Operation
When the ignition is switched ON, the
i-ACTIVSENSE status symbol (warning/
risk avoidance support system) (white)
turns on and the system goes on
standby.
NOTE
If the i-ACTIVSENSE status symbol
(warning/risk avoidance support
system) (white) does not turn on, the
system is cancelled using the
i-ACTIVSENSE switch or the
personalisation feature.
Operation conditions
When all of the following conditions
are met, the i-ACTIVSENSE status
symbol (warning/risk avoidance
support system) on the
multi-information display changes
from white to green and the system
becomes operational.
xThe vehicle speed is about 60 km/h
(37 mph) or faster.
xThe system detects white (yellow)
lane lines.
NOTE
When the system does not detect a
white (yellow) lane line on one side
only, the system does not operate on
the side that is not being detected.
When temporarily cancelling the
system
The LAS goes on standby in the
following cases: The LAS operation is
automatically restored when the
system's operation conditions are met.
xThe system cannot detect white
(yellow) lane lines.
xThe vehicle speed is less than about
55 km/h (34 mph).
xThe direction indicator lever is
operated.
xThe accelerator pedal is depressed
abruptly.
xThe TCS/DSC is operating.xThe TCS is turned
off.xThe steering wheel is operated.xThe brake pedal is operated.
The function is temporarily stopped.
The LAS stops functioning in the
following cases:
xThe temperature in the forward
sensing camera (FSC) is too high or
too low.
xThe windscreen around the forward
sensing camera (FSC) is foggy.
xThe windscreen around the forward
sensing camera (FSC) is blocked by
an obstruction, causing poor forward
visibility.
xStrong light (such as sunlight, or
headlights (high-beam) of
on-coming vehicles) is directed at
the forward sensing camera (FSC).
System malfunction
If there is a problem with the system,
the i-ACTIVSENSE status symbol
When Driving
i-ACTIVSENSE
4-164

(warning/risk avoidance support
system) (white) and the i-ACTIVSENSE
warning indication/warning light on
the multi-information display turns on
and a message is indicated.
Refer to i-ACTIVSENSE Status Symbol
(Warning/Risk Avoidance Support
System) on page 4-96.
▼Steering Wheel Operation Assist
When the system determines that the
vehicle might be deviating from its
lane, the steering wheel operation
assist operates.
The system notifies the driver that it
provided steering wheel operation
assistance on the multi-information
display and the active driving display.
Multi-information display (Basic
display)
Multi-information display
(i-ACTIVSENSE display)
Active driving display
NOTE
When the driver operates the steering
wheel while the steering wheel
operation assist is operating , the
steering wheel operation assistance is
cancelled.
▼System Cancelling
The LAS can be set to inoperable.
x(If only the LAS is turned
off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the LAS is turned off by operating
the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-165

Adjustable Speed Limiter
(ASL)
*
▼Adjustable Speed Limiter (ASL)
The ASL is a function to prevent the
vehicle from being driven at a vehicle
speed faster than a set speed. The
vehicle speed is controlled to kept it
below the set speed even if the
accelerator pedal is depressed.
The ASL can be set between 30 km/h
(19 mph) and 200 km/h (125 mph).
The vehicle speed may exceed the set
speed when the vehicle is driven on a
down slope, however, the system
notifies the driver by flashing the
display and operating a warning
sound.
WARNING
Always turn off the system when
changing drivers:
If the driver is changed and the new
driver is unaware of the ASL function,
the vehicle may not accelerate when
the driver depresses the accelerator
pedal, leading to an accident.
The system consists of the ASL display
and the speed limiter switch on the
steering wheel.
Multi-information display (Basic
display)
1. ASL set vehicle speed

Multi-information display
(i-ACTIVSENSE display)
1. ASL set vehicle speed

Active driving display
1. ASL set vehicle speed

When Driving
i-ACTIVSENSE
4-166*Some models.

Speed limiter switch
1. CANCEL switch
2. RES switch
3. LIM switch
▼Adjustable Speed Limiter (ASL)
Standby Indication (White)/
Adjustable Speed Limiter (ASL) Set
Indication (Green)
ASL standby indication (white)
The indication is display in white when
the LIM switch is pressed and the ASL
is activated.
ASL set indication (green)
The indication is display in green when
a speed has been set.
When Driving
i-ACTIVSENSE
4-167

▼Adjustable Speed Limiter (ASL) Display
The setting status of the ASL is displayed in the active driving display or the display in
the instrument cluster.
StatusIndication on
multi-informa-
tion display/
active driving
displayExplanation
Stand-by dis-
play
Displays when the speed limiter switch is operated and the system
is turned on.
Turns off when the system is turned off.
Setting display
Displays when the SET- or SET+ switch is operated and the speed is
set.
Cancel display
Displays when any of the following operations is done and the sys-
tem is temporarily cancelled.
xCANCEL switch is operatedxAccelerator pedal is strongly depressed
Warning display
If the vehicle speed exceeds the set speed by about 5 km/h (3
mph) or more, the ASL display
flashes.
The display flashes until the vehicle speed decreases to the set
speed or less.
A warning beep is activated at the same time as the warning dis-
play.
Refer to Speed Limiter Warning Beep on page 7-72.
▼Activation/Deactivation
NOTE
When the ignition is switched
off, the
system status before it was turned
off is
maintained.
For example, if the ignition is switched
off while the ASL is operating , the
system will be operable when the
ignition is switched ON the next time.
Activation
Press the LIM switch to activation the
system. The ASL screen is displayed,
and the ASL standby indication
displays in white.
Deactivation
Press the LIM switch again to
deactivation the system. The ASL
screen is no longer displayed and the
ASL indication does not display.
When Driving
i-ACTIVSENSE
4-168

▼Setting the System
WARNING
Always verify the safety of the
surrounding area when setting the
ASL:
If the speed is set lower than the
current vehicle speed, the vehicle
speed is decreased to the set speed.
Verify the safety of the surrounding
area and keep a safer distance
between vehicles ahead and behind
you.
1. Press the LIM switch to turn the
system on.
2. Press the RES switch up (SET+) or
down (SET-) to set the speed.
When the current vehicle speed is
30 km/h (19 mph) or more, the
speed is set to the current vehicle
speed. When the current vehicle
speed is less than 30 km/h (19
mph), the speed is set to 30 km/h
(19 mph).
3. To increase the set speed, press the
RES switch up (SET+) continuously.
The set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES switch up (SET
+) momentary. For example, the set
speed increases about 4 km/h (4
mph) by pressing the RES switch up
(SET+) 4 times.
4. To decrease the set speed, press the
RES down
(SET-) continuously. The
set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES down
(SET-)
momentary. For example, the set
speed decreases about 4 km/h (4
mph) by pressing the RES down
(SET-) 4 times.
NOTE
xWhen the vehicle set speed is
displayed in the instrument cluster,
press the RES switch to set the
displayed vehicle speed.
xThe system is temporarily cancelled
when the vehicle is accelerated by
depressing the accelerator pedal
strongly, however, it resumes when
the vehicle speed decreases to the
set speed or less.
xThe vehicle speed may exceed the
set speed on a down slope.
xIn the following cases, the system
cannot be set.
xAny door is open.xThe driver's seat belt is unfastened.
▼Temporarily Cancelling the System
The system is temporarily cancelled
(stand-by status) when any of the
following operations is done while the
ASL is displayed.
xCANCEL switch is pressedxAccelerator pedal is strongly
depressed
xAny door is openedxThe driver’s seat belt is unfastened
Press the RES switch to resume the
operation at the previous set speed.
The ASL display remains displayed.
NOTE
xThe set speed can be set by pressing
the RES switch up (SET+) or down
(SET-) while the system is in stand-by
status.
xThe ASL is not cancelled by
depressing the brake pedal.
When Driving
i-ACTIVSENSE
4-169

Intelligent Speed
Assistance (ISA)
*
▼Intelligent Speed Assistance (ISA)
The ISA is a function which keeps the
vehicle speed below the speed limit
set from a speed limit sign or an
optionally set speed limit. The speed
limit can be set between 30 and 200
km/h (19-125 mph), and if the vehicle
speed exceeds the set speed limit
while driving on steep slopes, the
system notifies the driver using the
display and a warning sound.
The ISA recognises a speed limit sign
based on the
Tra ffi c Sign Recognition
System (TSR) or the navigation system
information.
Refer to
Tra ffi c Sign Recognition
System (TSR) on page 4-111.
WARNING
Always turn
off the system when
changing drivers:
If the driver is changed and the new
driver is unaware of the ISA function,
the vehicle may not accelerate when
the driver depresses the accelerator
pedal, leading to an accident.
Depending on the weather conditions
or problems with traffic signs, a traffic
sign may not be recognised or a traffic
sign
different from the actual
traffic
sign may be displayed. Always make it
your responsibility as a driver to check
the actual traffic signs. Otherwise, it
could result in an accident.
NOTE
The ISA operates only when the
navigation system's SD card (Mazda
genuine) is inserted. In addition, the
Adjustable Speed Limiter (ASL)
operates only when the navigation
system's SD card (Mazda genuine) is
not inserted. Refer to Adjustable
Speed Limiter (ASL) on page 4-166.
The system consists of the ISA display
and the speed limiter switch on the
steering wheel.

Multi-information display (Basic
display)
1. set vehicle speed

When Driving
i-ACTIVSENSE
4-170*Some models.