sensor MAZDA MODEL CX-9 2019 (in English) Manual Online

▼Taking Action
Take the appropriate action and verify that the warning light t
urns off.
SignalWarning Action to be taken
(Amber)
Smart Brake Support/
Smart City Brake Sup‐
port (SBS/SCBS)
Warning Indication
*
The light turns on if the windshield or the
radar sensor are dirty, or there is a malfunc‐
tion in the system. Verify the reason why the warning light is
illuminated on the center display.
If the reason why the warning light is illu‐
minated is due to a dirty windshield, clean
the windshield.
If the warning light is illuminated because
of a dirty radar sensor, clean the front em‐
blem.
For any other reasons, have the vehicle in‐
spected at an Authorized Mazda Dealer.
Low Fuel Warning In‐
dication/Warning Light The light turns on when the remaining fuel
is about 9.0 L (2.3 US gal, 1.9 Imp gal).NOTE
The light illumination timing may vary be
‐
cause fuel inside the fuel tank moves
around according to the driving conditions
and the vehicle posture. Add fuel.
Check Fuel Cap Warn‐
ing Indication/Warning Light If the check fuel cap warning light illumi‐
nates while driving, the fuel-filler cap may
not be installed properly.
Stop the engine and rein
stall the fuel-filler
cap.
Refer to Refueling on page 3-30.
Engine Oil Level Warning Light This warning light indicates that the engine
oil level is around the MIN mark (page
6-24).
Add 1 L (0.3 US gal, 0.2 Imp gal) of en‐
gine oil (page 6-23).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-37
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

SignalWarning Action to be taken
Seat Belt Warning
Light (Front seat) Except Mexico
The seat belt warning light turns on if the
driver or front passeng
er's seat is occupied
and the seat belt is not fastened with the ig‐
nition switched ON.
If the driver or front passenger's seat belt is
unfastened (only when the front passenger's
seat is occupied) and the vehicle is driven at
a speed faster than abo ut 20 km/h (12 mph),
the warning light flash es. After a short time,
the warning light stops flashing, but re‐
mains illuminated.
NOTE
The warning light fla shes for about 6
seconds if the driver's seat belt is not fas ‐
tened when the ignition is switched ON.
To allow the front passenger occupant
classification sensor to function properly,
do not place and sit on an additional seat
cushion on the front passenger's seat.
The sensor may not function properly be‐
cause the additional seat cushion could
cause sensor interference.
If a small child is seated on the front pas ‐
senger's seat, the warning light may not
operate. Fasten the seat belts.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-38
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

SignalWarning Action to be taken
Seat Belt Warning
Light (Front seat) Mexico
The seat belt warning light turns on if the
driver or front passenger's seat is occupied
and the seat belt is not
fastened with the ig‐
nition switched ON.
If the driver or front passenger's seat belt is
unfastened (only when the front passenger's
seat is occupied) and the vehicle is driven at
a speed faster than abo ut 20 km/h (12 mph),
the warning light flash es. After a short time,
the warning light stops flashing, but re‐
mains illuminated. If a seat belt remains un‐
fastened, the warning light flashes again for
a given period of time.
NOTE
Placing heavy items on the front pas‐
senger's seat may cause the front pas ‐
senger's seat belt warning function to op ‐
erate depending on the weight of the
item.
To allow the front passenger seat weight
sensor to function properly, do not place
and sit on an additional seat cushion on
the front passenger's seat. The sensor
may not function properly because the
additional seat cushion could cause sen ‐
sor interference.
If a small child is seated on the front pas‐
senger's seat, the warning light may not
operate. Fasten the seat belts.
(Red)
Seat Belt Warning
Light (Rear seat)
*
If the rear seat belts are not fastened while
the ignition is switched ON , the driver and
the passenger are alerted by the warning
light.
The warning light operates even if there is
no passenger on the rear seat.
NOTE
If a rear seat belt is not fastened by a cer ‐
tain period of time after the engine has
been started, the warning light turns off. Fasten the seat belts.
Low Washer Fluid
Level Warning Indica‐
tion
*
This warning light indicates that little wash‐
er fluid remains. Add washer fluid (page 6-27).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-39
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

NOTE
To allow the front passenger occupant
classification sensor to function
properly, do not place and sit on an
additional seat cushion on the front
passenger's seat. The sensor may not
function properly because the additional
seat cushion could cause sensor
interference.
If a small child is seated on the front
passenger's seat, the warning beep may
not operate.
Mexico
If the vehicle speed exceeds about 20
km/h (12 mph) with the driver or front
passenger's seat belt unfastened, a warning
beep sounds continuously. If the seat belt
remains unfastened, the beep sound stops
once and then continues for about 90
seconds. The beep stops after the driver or
front passenger's seat belt is fastened.
Until a seat belt is fastened or a given
period of time has elapsed, the beep sound
will not stop even if the vehicle speed falls
below 20 km/h (12 mph).
NOTE
Placing heavy items on the front
passenger's seat may cause the front
passenger's seat belt warning function
to operate depending on the weight of
the item.
To allow the front passenger seat weight
sensor to function properly, do not place
and sit on an additional seat cushion on
the front passenger's seat. The sensor
may not function properly because the
additional seat cushion could cause
sensor interference.
If a small child is seated on the front
passenger's seat, the warning beep may
not operate.
Rear seat
*
The warning beep only sounds if a seat
belt is unfastened after being fastened.
▼ Ignition Not Switched Off (STOP)
Warning Beep
If the driver's door is opened with the
ignition switched to ACC, a beep will be
heard continuously in the cabin to notify
the driver that the
ignition has not been
switched OFF (STOP). Under this
condition, the keyles s entry system will
not operate, the vehicle cannot be locked,
and the battery voltage will be depleted.
▼ Key Removed from Vehicle Warning
Beep
Vehicles with advanced keyless function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, the beep which
sounds outside of the vehicle will be heard
6 times, the beep which sounds inside the
vehicle will be
heard 6 times.
Vehicles without advanced keyless
function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, a beep will be heard
in the cabin 6 times.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key is
carried together with a metal object or it
is placed in a poor si gnal reception area.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-47
CX-9_8HB2-EA-18G_Edition1 2018-5-11 13:09:27

▼Power Steering Warning Buzzer
If the power steering system has a
malfunction, the power steering
malfunction indication/malfunction
indicator light turns on or flashes and the
buzzer operates at the same time.
Refer to Stop Vehi
cle in Safe Place
Immediately on page 7-28.
▼ Tire Inflation Pressure Warning
Beep*
The warning beep sound will be heard for
about 3 seconds if the tire pressures
decrease.
Refer to Tire Pressure Monitoring System
on page 4-208.
▼Blind Spot Monitoring (BSM)
Warning Beep*
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monit
oring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-10.
Reversing
The Blind Spot Monitoring (BSM)
warning sound is activated if there is a
possibility of collision with a vehicle
approaching from behind and from the
rear on the left and right sides of the
vehicle.
▼ Excessive Speed Warning*
If the vehicle speed exceeds the speed
limit sign displayed
on the active driving
display, the warning sound is activated and
the area around the speed limit sign
displayed on the active driving display
flashes 3 times in amber, and if the vehicle
speed continues to exceed the displayed
speed limit sign, the indication stops
flashing and remains on.
▼ Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) System
War ni ng s
*
The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop &
Go function) system warnings notify the
driver of system pr
oblems and precautions
on use when required. Check after hearing
a warning beep sound.
Warning beep What to check
While the Mazda Radar
Cruise Control with Stop
& Go function (MRCC
with Stop & Go func‐
tion) system is operating,
a single beep sound is
heard when “Front Ra‐
dar Sensor Blocked” is
displayed in the mul‐
ti-information display. Cancel the Mazda Radar
Cruise Control with Stop
& Go function (MRCC
with Stop & Go func‐
tion) system if the radar
sensor (front) becomes
dirty. Clean the area
around the radar sensor
(front).
The beep sounds inter‐
mittently while the vehi‐
cle is being driven. The distance between
your vehicle and the ve‐
hicle ahead is too close.
Verify the safety of the
surrounding area and re‐
duce vehicle speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-49
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

Warning beep What to check
While the Mazda Radar
Cruise Control with Stop
& Go function (MRCC
with Stop & Go func‐
tion) system is operating,
a single beep sound is
heard when “Front Ra‐
dar Sensor System Mal‐
function” is displayed in
the multi-information
display. A malfunction in the
system may be indicated.
Check the center display
to verify the problem
and then have your vehi‐
cle inspected by an Au‐
thorized Mazda Dealer.
▼
Lane Departure Warning Sound*
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
The volume of the Lane-keep Assist
System (LAS) & Lane Departure
Warning System (LDWS) warning sound
can be changed.
Refer to Personalization Features on
page 9-10.
The type of the Lane-keep Assist System
(LAS) & Lane Departure Warning
System (LDWS) warning sound can be
changed.
Refer to Personalization Features on
page 9-10.
▼
Collision warning*
If there is a possibility of a collision with a
vehicle ahead, a warning sound is
activated at the same time as the warning
indications are displayed in the instrument
cluster or active driving display.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-50*Some models.
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

ItemFeatureFactory Set‐
ting Available Set‐
tings Settings
Change
Method
Blind Spot Mon‐
itoring (BSM)
(page 4-114) The system can be chan
ged so that Blind Spot
Monitoring (BSM) does not operate.*1On On/Off A ―
Warning beep volume*2High High/
Low/ Off A―
Distance Recog‐
nition Support
System (DRSS)
(page 4-126) The system can be chan
ged so that Distance
Recognition Support System (DRSS) does not
operate.*1On On/Off A ―
The distance at which the vehicle ahead and
your vehicle indicated in the display flashes in
white can be changed. Near Far/Med./Near A ―
Traffic Sign
Recognition
System (TSR)
*3
(page 4-120)The Traffic Sign Recognition System (TSR)
can be set to inoperable.
*1On On/Off A ―
The warning pattern of the excessive speed
warning can be changed.
OffOff/
Vis u a l /
Audio & Visual A―
The activation timing fo
r the excessive speed
warning can be changed.00/5/10 A―
360° View Mon‐
itor (page 4-166) Setting can be changed so that the 360° view
monitor is automatically displayed when the
ignition is switched to ON.
Off On/Off A ―Setting can be changed so that the display of
the estimated forward l
ine of progress is not
displayed. On On/Off A ―
Setting can be changed so
that the top view/
front view displayed while the vehicle is mov‐
ing in the forward direc tion after reversing is
not displayed. On On/Off A ―
Parking sensor
system (page
4-225)
Display*4/non-display
On On/Off A ―
Specifications
Personalization Features
9-12
CX-9_8HB2-EA-18G_Edition1
2018-5-11 13:09:27

ItemFeatureFactory Set‐
ting Available Set‐
tings Settings
Change
Method
Active driving display (page 4-56)
Display Setting can be changed so that the Active Driv‐
ing Display is not displayed.
On On/Off C ―
The display height (up/down position) can be
changed.
013 steps up/
down from ini‐
tial setting (total: 27 steps) C―
The method for adjusting the display bright‐
ness (automatically/manually) can be changed.
Auto Auto/Man. C ―
The standard brightness with the automatic
brightness adjustment can be changed. 02 steps up/down
from initial set‐ ting (total: 5
steps) C―
The standard brightness with the manual
brightness adjustment can be changed.
020 steps up/
down from ini‐
tial setting (total: 41 steps) C―
The display angle can be changed.
03steps up/down
from initial set‐ ting (total:7steps) C―
Navigation guid‐
ance
Display/non-display On On/Off C ―
*1 Though these systems can be tur
ned Off, doing so will defeat the purpose of the system and Mazda
recommends that these systems remain On.
*2 Only the volume of the warning beep during Blind Spot Monitori ng (BSM) operation can be changed. The
volume of the warning beep durin g Rear Cross Traffic Alert (RCTA) operation cannot be changed.
*3 This system functions only when t he navigation system is functioning.*4 When the ultrasonic sensors detect an obstruction, the content s indicated on the center display switches to the
360°View Monitor. (Vehicles with 360°View Monitor)
*5 If the auto-wiper control is set to Off, the wiper lever position is set to in termittent operation.*6 If the setting is changed to O ff, the following operation is performed according to the headlight switch
position:
At position: Headlights turn off immediately after the ignition i s switched off.At any position other than : Headlights on/off conditions vary according to the headlight switch
position. Refer to Headlights on page 4-68.
*7 When set to 0 seconds, the lights-on reminder is operable.*8 The lights-on reminder settings can be changed at anytime, how ever, the lights-on reminder only operates
when the auto headlight function is set to Off. Refer to Lights-On Reminder on page 7-46.
*9 Change the ambient light illumin ation level with the parking lights or headlights turned on.*10 When set to OFF, the ambient lights remain turned off regardless of whether or not the parking lights or
headlights are on or off. However, they will turn on or off in conjunction with the illuminated entry system.
Specifications
Personalization Features
9-16
CX-9_8HB2-EA-18G_Edition1 2018-5-11 13:09:27

Index
Dashboard Illumination............... 4-49
Engine Coolant Temperature
Gauge........................................... 4-48
Fuel Gauge.................................. 4-48
Indication/Indi cator Lights.......... 4-53
Multi-information Display (Type
C)................................................. 4-46
Odometer..................................... 4-47
Outside Temperature Display...... 4-49
Speedometer................................ 4-45
Tachometer.................................. 4-45
Trip Computer............................. 4-50
Trip Meter....................................4-47
Warning Indication/Warning
Lights........................................... 4-52
Interior Care...................................... 6-63
Active driving display
maintenance................................. 6-65
Cleaning the floor mats............... 6-65
Cleaning the window interiors.....6-65
Instrument panel top
maintenance................................. 6-64
Leather upholstery
maintenance................................. 6-64
Panel maintenance....................... 6-65
Plastic part maintenance.............. 6-64
Seat belt maintenance..................6-63
Upholstery maintena nce.............. 6-64
Vinyl upholstery maintenance..... 6-63
Interior Lights................................... 5-93 Luggage compartment light.........5-93
Map lights....................................5-93
Overhead lights............................5-93
i-ACTIVSENSE.............................. 4-107
Active safety techno logy........... 4-107
Adaptive Front Lighting System
(AFS)......................................... 4-110
Advanced Smart City Brake Support
(Advanced SCBS)..................... 4-158
Blind Spot Monitoring (BSM)... 4-114
Camera and sensors................... 4-108Distance Recognition Support System
(DRSS).......................................4-126
Forward Sensing Camera
(FSC)......................................... 4-192
High Beam Control System
(HBC).........................................4-111
Lane-keep Assist System (LAS) &
Lane Departure Warning System
(LDWS)..................................... 4-147
Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function)..................4-134
Pre-crash safety technology.......4-108
Radar sensors (rear)...................4-200
Radar sensor (front)...................4-197
Rear Cross Traffic Alert
(RCTA)...................................... 4-130
Smart Brake Suppor t (SBS)...... 4-164
Smart City Brake Support
(SCBS)....................................... 4-161
Traffic Sign Recognition System
(TSR)......................................... 4-120
360°View Monitor..................... 4-166
i-ACTIV AWD Operation...............4-104
J
Jack...................................................... 7-4
Jump-Starting.................................... 7-19
K
Keyless Entry System......................... 3-3
Keys.....................................................3-2
Key suspend function.................... 3-8
Transmitter..................................... 3-4
Key Left-in-luggage Compartment
Warning beep (With the advanced
keyless function)............................... 7-48
Key Left-in-trunk Warning Beep (With
the advanced keyless function)......... 7-48
10-6
CX-9_8HB2-EA-18G_Edition1 2018-5-11 13:09:27

Index
Key Left-in-vehicle Warning Beep (With
the advanced keyless function)......... 7-48
Key Removed from Vehicle Warning
Beep...................................................7-47
Key Suspend Function........................ 3-8
L
Label Information............................... 9-2
Lane Departure Warning sound........ 7-50
Lane-change Signals......................... 4-74
Lane-keep Assist System (LAS) & Lane
Departure Warning System
(LDWS)........................................... 4-147
Leaving Home Light......................... 4-71
Liftgate.............................................. 3-19When Liftgate Cannot be
Opened......................................... 7-51
Lighting Control................................4-68
Lights-on Reminder.......................... 7-46
Light Bulbs Replacement................................ 6-42
Specifications.................................9-6
Lubricant Quality ................................ 9-4
Luggage Compartment....................5-103 Cargo Securing Loops............... 5-103
Cargo Sub-Compartment........... 5-103
Luggage Compartment Light............ 5-93
M
Maintenance Information.................................... 6-2
Scheduled.......................................6-4
Maintenance Monitor........................ 6-16
Map Lights........................................ 5-93
Mazda Radar Cruise Control with Stop &
Go function (MRCC with Stop & Go
function).......................................... 4-134 Close proximity warning........... 4-137
Cruise control function.............. 4-144
Display indication......................4-136
Setting the system..................... 4-138
Stop hold control....................... 4-143
Message Indicated in Multi-information
Display.............................................. 7-45
Message Indicated on Display.......... 7-43
Meters................................................ 4-11
Mirrors
Outside mirrors..... ....................... 3-32
Rearview mirror.......................... 3-34
Mirror Defogger......... ....................... 4-79
Moonroof...........................................3-40
Multi-information Display (Type
A).......................................................4-13
Multi-information Display (Type
B)....................................................... 4-30
Multi-information Display (Type
C)....................................................... 4-46
O
Outside Mirrors......... ........................ 3-32
Overhead Console........................... 5-101
Overhead Lights................................ 5-93
Overheating....................................... 7-23
Overloading....................................... 3-52
Owner Maintenance Closing the hood...... ................... 6-21
Engine compartment overview.... 6-22
Key battery replacemen t..............6-36
Opening the hood........................ 6-20
Owner maintenance
precautions................................... 6-18
P
Parking Sensor System................... 4-220
Personalization Features................... 9-10
Power Liftgate................................... 3-21
Power Liftgate Warning Beep........... 7-48
Power Steering................................ 4-106
Power Steering Warning Buzzer....... 7-49
Power Windows............. ................... 3-37
10-7
CX-9_8HB2-EA-18G_Edition1 2018-5-11 13:09:27