air condition MAZDA PROTEGE 1992 User Guide

OUTLINE
Component Function Remark
Engine control unit (ECU) Controls operation of the following:
(Cont’d)
1. A/C (Cut-off) 1. A/C relay
2. Fail-safe function 2. Self-Diagnosis Checker and MIL
3. Fuel injection system 3. Injector
4. idle speed control 4. Idle speed control (ISC) valve
5. Ignition timing control system 5. Igniter
6. Monitor function 6. Monitor lamp (Self-Diagnosis Checker)
7. Pressure regulator control system 7. Solenoid valve
(Pressure regulator control) (BP)
8. Purge control system 8. Purge control solenoid valve
9. VICS 9. Solenoid valve (WCS) (DOHC) Fuel filter
Filters particles from fuel Fuel pump
Provides fuel to injectors l Operates while engine running l Installed in fuel tank Igniter
Receives spark signal from ECU and gener-
ates high voltage in ignition coil Ignition switch
Engine cranking signal sent to ECU (START position)
Inhibitor switch (ATX)
Detects in-gear condition; sends signal to Switch ON in N or P range
ECU Injector
Intake air thermosensor
Idle speed control (ISC)
valve
Main relay
(FUEL INJ relay)
MIL (Malfunction
indicator lamp)
Neutral switch (MTX)
Oxygen sensor
PCV valve
P/S pressure switch
Pressure regulator
Resonance chamber
Resonance duct
Separator
Stoplight switch
Solenoid valve
(Purge control)
Shutter valve actuator
(DOHC)
Throttle body
Throttle sensor
Injects fuel into intake port l Controlled by signals from ECU
l High-ohmic injector
Detects intake air temperature; sends signal Installed on dynamic chamber
to ECU
Controls bypass air amount Controlled by duty signal from ECU
Supplies electric current to injectors, ECU,
etc.
Lamp flashes to indicate malfunction code
number of input and output devices
Detects in-gear condition; sends signal to
ECU
Detects oxygen concentration; sends signal
to ECU
Controls blowby gas introduced into engine
Detects P/S operation; sends signal to ECU
Adjusts fuel pressure supplied to injectors
Reduces intake air noise
Reduces intake air noise
Prevents fuel from flowing into charcoal
canister
Detects braking operation (deceleration),
sends signal to ECU
Controls evaporative fumes from canister to
intake manifold
Closes/opens shutter valve to improve
torque characteristics
Controls intake air quantity
l Detects throttle valve fully closed/fully
opened condition (MTX) TEN terminal grounded
Switch ON in neutral
Zirconia ceramic and platinum coating
P/S: ON when steering wheel turned right or
left
Controlled by duty signal from ECU
For Variable inertia charging system (VICS*)
Integrated throttle sensor, dashpot, and ISC
valve
l Detects throttle valve opening angle
(A-W
l Sends signals to ECU
F-l 7

F TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
ENGINE CONTROL OPERATION CHART
Note
Input Device and Engine Conditions
l The data in this chart is for reference only.
INPUT DEVICES APPROX,- SENSORS
MATE TIME G& THROTTLE SENSOR
(BASED ON TRIBUTOR
WATER INTAKE
10-16°C, (G. OXYGEN AIRFLOW AIR
VT
POW
.50-6OOF
SIGNAL)” ;;;;;f- SENSOR METER
AMBIENT) (Ne-SIGNAL) THERMO- TERMINAL TERMINAL yE\MINAL
CONDITIONS SENSOR (ATX)
WX)
A
c
CRANKING
-COLD ENGINE Signal has Signal has Signal has Signal has Slgnal has Slgnal has
l COLD AIR zero no affect no effect no effect no effect no effect
no effect
. COLD COOLANT on ECU on ECU on ECU on ECU on ECU
on ECU
Cool to A A
COLD START
warm: Low volume Closed Closed
Closed
-FAST IDLE
One
Medium airflow: throttle: throttle:
l COLD AIR
minute
voltage High volt-
Low volt- Low volt- throttle.
Low volt-
* COLD COOLANT
(3.5” and :zo:o, ,,Pbove 1’,“,“$; a(ogi-O,8”) ;149&“) we W)
dropping) to high
(68OF)]:
COLD DRIVEAWAY voltage A
Above
-PART THROTTLE Two (O-0.9”) 2.3”
l COLD AIR minutes
l COLD COOLANT
v v ,,
Warm: Medi- Sensor Moderate II
WARM DRIVEAWAY
volume air-
-PART THROTTLE Three N&IGNAL um voitage hot:
flow: Low
l WARM AIR minutes Sends all Vvwrox switching l WARM COOLANT cylinders 0.7V and
from high to medium
Part Part
TDC signal dropping) voltage voltage
throttle: throttle.
)
A (0.9V) (1 .o-3.5”)
to ECU
.“~ Medium Medium
HOT CRUISE
s voltage voltage
Open
l WARM AIR G-
SIGNAL”’ to low (0.8-3.0”) (4.5-5.5”) throttle:
l WARM COOLANT High
Sends No. voltage
1 cylinder (0.1”) voltage
1 (battery
TDC (com-
1 I voltage)
HOT ACCELERATION pression)
-60% THROTTLE signal to
Moderate
ECU
to strong
High Cool lo warm
voltage ;$,“,” Of j-20-4OT
f t
HOT ACCELERATION
More’ than Hot: Low (0.9”) Low (-4-‘04”F)l: W,ds open
voltage 1.5-4.3v
throttle: Wide open
-WIDE OPEN
four voltage
High volt- throttle
THROTTLE (0.5-1.5V)
minutes (Below High
0.5”) age (Above
voltage (OV)
t 1 3.OV)
I,
A 1. /I
DECELERATION
-CLOSED THROTTLE
HOT CURB IDLE
-EXTENDED
HOT ENGINE
SHUTDOWN Low
voltage
(0”) Low Closed Closed
Closed
volume throttle: throttle.
throttle.
of airflow:
~~~~!$$ (Above Low Low
Low
voltage voltage
voltage
to low 3.OV) (0.2-0.N) (4.5-5 5V) (OV)
voltage
(0.75%
t t 1 0.25”)
r v 1 I I
Sensor
hot: Low
OFF OFF voltage
-
(0.1”) until OFF OFF OFF OFF
OFF
sensw
COOIS
._-

F TROUBLESHOOTING GUIDE
Output Devices and Engine Conditions
Note
. The data in this chart is for reference only.
INJECTOR
CONDITIONS
CRANKING
-COLD ENGINE
l COLD AIR l COLD COOLANT
COLD START
-FAST IDLE
l COLD AIR l COLD COOLANT
COLD DRIVEAWAY
-PART THROTTLE
l COLD AIR l COLD COOLANT
WARM DRIVEAWAY
-PART THROTTLE
. WARM AIR
l WARM COOLANT
HOT CRUISE
l WARM AIR l WARM COOLANT Zero
One
mrnute
Two
minutes
Three
minutes
I AIR
INJECTION “AL”E
INJECTION TlMlNG
A
All A
cylinders
each
ignition
pulse
1
Rich Open:
coolant
tem-
perature:
Below
40%
(104OF)
,
I/
Rich and
2-group” 1’
lean l-group” /I
,
i
HOT ACCELERATION
-60% THROTTLE
-lOT ACCELERATION
-WIDE OPEN
THROTTLE
Closed ISC
VALVE
1, THREE-WAY
SOLENOID SOLENOID
VALVE VALVE
(PURGE
(PRESSURE
CONTROL) REGULATOR
CONTROL)‘3
c
OFF
(Purge
cut)
Large
1
, AK
RELAY
amount or
bypass air
OFF
(Vacuum
to
pressure
regulator)
After start-
rng: ON dur-
ing hot start
only (Vacu-
um cut)
OFF
l 2 SOHC, *’ BP
F-22

TROUBLESHOOTING GUIDE F
USING THIS SECTION
Introduction
Most of the fuel and emission control system is electrically controlled, often making it difficult to diagnose
problems in the system, especially intermittent problems, Before undertaking actual checks, take a few minutes
to talk with a customer who approaches with a drivability complaint. The customer is often a good source
of information on such problems, especially intermittent ones. Through talks with the customer, one can find
out what the symptoms are and under what conditions they occur.
Work flow
CHECK IN
LISTEN TO CUSTOMER COMPLAINTS
REFER TO TROUBLESHOOTING PAGE THAT - - - - - - - - - - - DIAGNOSTIC INDEX
CORRESPONDS TO ACTUAL SYMPTOM (Refer to page F-23)
CHECK FOR WHAT IS BAD IN SYSTEM - - - - - - - - - - - - - INSPECTION
1
CHECK FOR WHAT PART IS BAD - - - - - - -,- - - - - - - ACTION
i I
REPAIR/REPLACEMENT - - - - - - - - 1
I
DETERMINE IF TROUBLE HAS BEEN ELIMINATED
1 Yes
CHECK OUT
13lJOFX-008
Diagnostic index
No.:
Each troubleshooting item is
assigned a number.
TROUBLESHOOTING ITEM: There are 29 troubleshooting
items. Choose the item that
most closely
corresponds to
the actual symptom.
TROUBLESHOOTING GUIDE
‘ROUBLESHOOTINl3 ITEM
f H
DESCRIPTION
iE
7
-
DESCRIPTION:
Describes each troubleshooting
item.
/
PAGE:
Shows the reference page.
OWOFX-014
F-25

F TROUBLESHOOTING GUIDE
Troubleshooting chart
6 I
CRANKS NORMALLY BUT HARD TO START - WHEN ENGINE COLD
*Engine cranks at normal speed but requires excessive crankmg time before starting
IESCRIP-
l Batterv in normal condition
llON l Restans OK after warmup l Engine runs normally at idle [If Idle condrtron is not OK, refer to “Rough idle” (Nos. S-12)]
TROUBLESHOOTING HINTS]
B Air/Fuel mrxture too rrch @Air/Fuel mixture too lean
l Arrflow meter stickrng l Fuel iniectron control malfunction
l Aw cleaner element clogged
*Idle weed control malfunction (Correction for coolant temperature)
0 Poor atomizatron
- ~~ ~~ *Low RVP (summer) fuel is used rn cold weather >
f INSPECTION T Check If “00” is displayed on Self-Diagnosis
Checker wth Ignition switch ON -
Yes
No CT page F-73
SYSTEM SELECT: 1
“SELECT SW: A
Check if ECU terminal voltages are OK
(Especially 1C. 2D. and 2Q)
cc page F-144
Check If engine starts easily when throttle valve -
Yes
-
NO
-
Yes ACTION
Go to next step
Malfunctlon Code No. dlsplayed
Check for cause (Refer to specified
check sequence)
“58” flashes CT- page F-79
Check ECU terminal 1F voltage
Speciflcetlon: Battery voltage CT page F-144
(Ignition ewltch ON)
+ If OK, replace ECU CT page F-143
e If. not OK, check wrring between
ECU and Self-Diagnoos Checker
Go to next step
Check for cause CI page F-145
(-!hnrlr ,‘ ICP ..-I..- .^ nv
c+ page F-103
13UOFX-009
DESCRIPTION:
Further describes the symptom. Confirm that the chart addresses the actual symptom before beginning
troubleshooting.
TROUBLESHOOTING HINTS:
This describes the possible point of malfunction.
STEP:
This shows the order of troubleshooting. Proceed with troubleshooting as indicated.
INSPECTION:
This describes an inspection to quickly determine the malfunction of parts. If a detailed procedure is necessary
to perform the INSPECTION, refer to the page shown by the “~7” mark.
ACTION:
This recommends the appropriate action to take as a result (Yes/No) of the INSPECTION. How to perform
the action is described on the reference page shown by the “~7” mark.
OWOFX-016
F-26

F TROUBLESHOOTING GUIDE
3 CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) - WHEN ENGINE COLD
DESCRIP- *Engine cranks at normal speed but shows only partial combustion and will not continue to run
TION
l Battery in normal condition
*Fuel in tank
[TROUBLESHOOTING HINTS]
0 Air/Fuel mixture too rich
*Air cleaner element clogged
l Airflow meter stuck @ Low engine compression
@ Air/Fuel mixture too lean
l Fuel injection control malfunction
(Correction for coolant temperature)
*Low fuel line pressure
*Air leakage of intake air system
Checker with ignition switch ON
CT page F-83
w page F-150
Specification: Battery voltage
(Ignition switch ON)
W: SELF TEST w page F-149
Fuel line pressure:
285-314 kPa (2.7-3.2 kg/cm’, 38-48 psi) If fuel line pressure quickly in-
creases, check pressure regulator CF- page F-129
d If fuel line pressure gradually in-
creases check for clogging be-
I pump and pressure
Check if fuel return hose is clogged or
F-32

TROUBLESHOOTING GUIDE
TEP INSPECTION ACTION
4 Check if ECU terminal voltages are OK Yes Go to next step
MTX...Especially IC, 20 and 2Q
ATX... Especially lC, 2E and 3D v page F-150
No Check for cause ~3‘ page F-151
5
Check for air leakage of intake air system com- Yes Repair or replace
ponents
No Go to next step
6 Check if engine starts when water thermosensor Yes Check water thermosensor c7 page F-158 is disconnected
Check for correct engine compression 82-10 ’ No
Check engine condition CIP page Bl-10
Engine compression: 82-10
l BP SOHC l Worn piston, piston rings or cylinder 834 kPa (8.5 kg/cm*, 121 psi)300 rpm
wall
l BP DOHC l Defective cylinder head gasket 883 kPa (9.0 kg/cm*, 128 psi)-300 rpm l Distorted cylinder head
l B8 l Improper valve seating 932 kPa (9.5 kg/cm*, 135 psi)300 rpm *Valve sticking in guide
9 Check if spark plugs are OK Yes Go to next step CT- page G-18
1.0-l .l mm
(0.039-0.043 in) DAMAGE AND
DETERIORATION No Clean, or replace c7 page G-18
10 Try known good ECU and check if condition
improves CT- page F-149
23UOFX-01 I
F-33

F TROUBLESHOOTING GUIDE
4
CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) - AFTER WARM-UP *Engine cranks at normal speed and shows partial combustion but will not continue to run after running and
DESCRIP- hot soaked
TION *Battery in normal condition
*Engine starts normally when cold
[TROUBLESHOOTING HINTS] 3 Air/Fuel mixture too rich
@ Vapor lock
l Insufficient fuel injection control
*Fuel pressure not held in fuel line after engine stopped
(Correction for coolant temperature)
*High RVP (winter) fuel used in warm weather
l Injector fuel leakage @ Pressure regulator control system malfunction [BP]
switch ON, then check if en
D‘ page F-134
Fuel line pressure:
265-314 kPa (2.7-3.2 kg/cm’, 36-46 psi) ne pressure w
+ If fuel line pressure quickly in-
if fuel return hose is clogged
or
F-=34

F TROUBLESHOOTING GUIDE
5
CRANKS NORMALLY BUT HARD TO START - ALWAYS
DESCRIP- l Engine cranks at normal speed but requires excessive cranking time before starting
TION l Battery in normal condition
*Engine runs normally at idle [If idle condition not OK, refer to “Rough idle” (Nos. 8-12)J [TROUBLESHOOTING HINTS]
@ Air/Fuel mixture too lean
@ Air/Fuel mixture too rich l Fuel injection control malfunction
(Correction for coolant temperature) *Air cleaner element clogged
l Airflow meter stuck
*Low fuel line pressure
l Air leakage @ Poor ignition spark
;TEP INSPECTION ACTION
1
Check if “00” is displayed on Self-Diagnosis Yes Go to next step
Checker with ignition switch ON W page F-82 No
Service Code No. displayed
Check for cause (Refer to specified SYSTEM SELECT: 1 check sequence) w page F-83
“88” flashes
Check ECU terminal 1F voltage w page F-150
Specification: Battery voltage
(Ignitlon switch ON)
* If OK, replace ECU w page F-149
W: SELF TEST c3 If not OK, check wiring between
ECU and Self-Diagnosis Checker
2 Check for correct intake manifold vacuum at idle
Yes Go to next step
VsCUUm: More than 450 mmHg (17.7 inHg) No Check for air leakage of intake air sys-
tem components
3 Check if air cleaner element is clean
Yes Go to next step w page F-79
No
Replace air cleaner element
4 Check if engine starts easily when throttle valve Yes Check throttle valve for carbon deposit
quarter open and then go to Step 6 Fuel line pressure:
265-314 kPa (2.7-3.2 kg/cm*, 38-46 psi)
(Vacuum hose to pressure regulator dis-
pressure while pinching
c3 If fuel line pressure quickly in-
creases, check pressure regulator w page F-129
c3 If fuel line pressure gradually in-
creases, check for clogging be-
tween fuel pump and pressure
If not clogged, check fuel pump
maximum pressure W- page F-126
F-36

TROUBLESHOOTING GUIDE F
CY page F-l 16
ATX... Especially IC, 2E and 3D
OK, repair or replace wire
ST” and check
for correct ignition timing at idl
*Worn piston, piston rings or cylinder
l Defective cylinder head gasket l Distorted cylinder head l Improper valve seating
aValve sticking in guide
known good ECU and check if condition
23UOFX-02
F-37