boot MAZDA PROTEGE 1992 User Guide

TRANSAXLE Jl
Clutch Housing and Transaxle Case Components
Caution
l Do not remove oil seals unless necessary.
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
-
.ACE
23UOJl-O(
1. Speedometer driven gear 17. Boot 28. Adjust shim
assembly 18. Oil seal (Change rod) 29. Adjust shim
2. Oil seal (Differential) Disassembly Note 30. Bearing outer race
Disassembly Note ,.,,,..,............. page Jl-18 (Differential)
..................... page Jl-19 19. Bushing Disassembly Note
Replacement (On-vehicle) 20. Oil seal (Primary shaft) ..................... page Jl-19
.....................
page Jl-20 Disassembly Note 31. Adjust shim (Differential)
3. Pivot ..................... page Jl-19 Disassembly Note
4. Bleeder 21. Bearing outer race ..................... page Jl-19
5. Bleeder cover Disassembly Note 32. Transaxle case
6. Gasket ..................... page Jl-18 33. Roll pin
7. Roll pin 22. Funnel 34. O-ring
8. Blind plug Disassembly Note 35. Driven gear
Disassembly Note ..................... page Jl-18 36. Packing
..................... page Jl-18 23. Bearing outer race 37. Oil seal
9. Reverse lever shaft (Differential) (Speedometer gear cace)
Disassembly Note Disassembly Note Disassembly Note
..................... page Jl-18 ..................... page Jl-19 ..................... page Jl-19
10. Lever set spring 24. Clutch housing 38. Gear case
11. Reverse lever 25. Oil passage 39. Joint
Inspection ....... page Jl-27 26. Oil seal (Differential) 40. Change rod
12. Guide plate assembly Disassembly Note
13. Roll pin ..................... page Jl-19
14. Selector Replacement (On-vehicle)
15. Change arm ..................... page Ji-20
16. Change rod assembly 27, Bearing outer race
Jl-17

Jl TRANSAXLE
r
03UOJ2-026
03UOJl-03:
Oil seal
Replacement (On-vehicle)
Jack up the vehicle and support it with safety stands. Drain
the transaxle oil. Next, use the following procedure to replace
the driveshaft oil seal:
1. Remove the front wheel.
2. Remove the splash shield.
3. Separate the front stabilizer from the lower arm.
Caution
l Do not damage the dust boots.
4. Remove the clinch bolt and pull the lower arm downward.
Separate the knuckle from the lower arm ball joint.
5. Loosen the nut and disconnect the tie-rod end with the SST.
Caution
l Do not subject the tripod joint to shock when remov-
ing the driveshaft.
6. Disconnect the driveshaft from the transaxle by prying with
a bar inserted between the outer ring and the transaxle.
7. Suspend the driveshaft with a rope.
03UOJl-036
8. Remove the oil seal with a screwdriver.
03UOJ2-03’
03UOJi-03;
51-20
Note
l Tap in until the oil seal installer contacts the case.
l Coat the oil seal lip with transaxle oil.
9. Tap the new oil seal into the transaxle case with the SST.

TRANSAXLE

I
\m/ 7.8-11 N-m
1. Change
rod
2. Joint
3. Bearing outer race
4. Funnel
Assembly Note 11. Oil passage
29. Guide plate assembly
12. Oil
seal (Differential) 30.
Gear case
Assembly Note 31, Oil seal
,.................... page Jl -41 (Speedometer gear cace)
13. Transaxle case Assembly Note
. . . . . . . . . . . . . . . . . . . . .
page Jl-42
5. Bearing outer race
Assembly Note
. . . . . . . . . . . . . . . . . . . . . page Jl-42
6. Bearing outer race
(Differential)
Assembly Note
. . . . . . . . . . . . . . . . . . . . . page Jl-41
7. Adjust shim (Differential)
Assembly Note
. . . . . . . . . . . . . . . ...*.. page Jl-41
8. Bearing outer race
(Secondary shaft gear)
Assembly Note
,..*.,...............
page Jl -41
9. Adjust shim
(Secondary shaft gear)
Assembly Note
. . . . . . ...*. . . . . . . . . . . page Jl-41
IO. Adjust shim
(Primary shaft gear)
Assembly Note
14. Reverse lever . . . . . . . . . . . . . . . . . . . . . page Jl-41
15. Lever set spring 32. Packing
16. Reverse lever shaft 33. O-ring
17. Roll pin 34. Drive gear
18. Blind plug 35. Roll pin
19. Oil seal (Primary shaft gear) (Speedometer driven gear
Assembly Note assembly)
. . . . . . . . . . . . . . . . . . . . . page Jl-42 Assembly Note
20. Gasket ..,......*. ..,,...... page Jl-41
21. Bleeder cover 36. Speedometer driven gear
22. Bushing assembly
23. Oil seal (Change rod) 37. Bleeder
Assembly Note 38. Pivot
..,..,...,........... page Jl-42 39. Oil seal (Differential)
24. Boot Assembly Note
Assembly Note . . . . . . . . . . . . . . . . . ...* page Jl-41
.,.,.,............... page Jl-42 40. Clutch housing
25. Change rod
Assembly Note
. ..*.................
page J l-42 .,................... page Jl-42
26. Change arm
27. Selector
28. Roll pin
Jl-36

Jl TRANSAXLE
03UOJl-10
-
23UOJl.01
Adjust shim (Primary shaft gear)
Caution
l Use adjust shim(s) selected during bearing preload
adjustment.
1. Apply transaxle oil to the adjust shim(s) and install it.
Funnel and bearing outer race
Caution
l Apply transaxle oil to the bearing outer race.
1. Install the funnel and the bearing outer race.
Oil seal (Primary shaft gear)
Caution
* Apply transaxle oil to outer circumference of the oil
seal.
1. install the new oil seal with a suitable pipe.
Oil seal (Change rod)
Caution
l Apply transaxle oil to the oil seal lip.
1. Install the oil seal.
Boot and change rod assembly
Caution
l Install the boot with the air bleed downward as
shown in the figure.
1. Slide the boot onto the change rod assembly.
2. Install the change rod assembly into the clutch housing.
-,
Jl-42

Jl SHIFT MECHANISM
SHIFT MECHANISM
OVERHAUL
1. Disassemble in the order shown in the figure.
2. Inspect all parts and repair or replace as necessary.
3. Assemble in the reverse order of disassembly, referring to
Assembly Note.
t
w 16-G (1.6-2.3, 12-17)
“..d
n /~~16--23 (1.6-2.3, 12-17)
1. Shift lever knob
2. Rear ashtray
3. Rear console
4. Front console
5. Boot
6. Nut
7. Washer
8. Bolt
9. Nut
10. Washer
Il. Bushing
12. Spring
Inspect for damage and weakness
Assembly Note.. . . . , . . . . . . . . . . . . . . . . . . . . page Jl -57
13. Shift lever
;45. “,Mlseat (upper)
Inspect for wear and damage
Jl-56
16. Holder
17. Ball seat (lower)
18. Nut
19. Washer
20. Pipe
21. Bushing
Inspect for wear and damage
22. Washer
23. Extension bar
Assembly Note,.. . . ., . . . . . . . . . . . . . . . . . . .
24. Insulator
Inspect for damage and cracks
25.
Nut
26. Bolt
27. Bushing
Inspect for wear and damage
28. Change control rod
Inspect for bending
142
page Jl -57

TRANSAXLE J2
1. Wheel and tire 14. Exhaust pipe
2. Splash shield 15. Engine mount No.2
3. Air hose and resonance chamber 16. Clutch release cylinder
4. Battery Removal Note .,...........,....,.,...... page J2-11
5. Battery carrier 17. Tie-rod end
6. Speedometer cable Removal Note . . . . . . . . . . . . . . . . ..*........ page J2-11
7. Back-up light switch connector 18. Stabilizer
8. Neutral switch connector 19. Driveshaft
9. Ground Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-12
10. Starter 20. Joint shaft
11. Extension bar 21. Engine mount No.4
12. Control rod 22. Transaxle
13. Engine mount member Removal Note ..,..,....*................ page J2-12
Removal Note . . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-1 1
03UOJ2-014
-
03UOJ2-01
Removal Note
Engine mount member
1. Suspend the engine with the SST and remove the engine
mount member.
Clutch release cylinder
Caution
l Do not damage the clutch pipe.
1. Remove the bolts shown.
2. Lay aside the clutch release cylinder and the clutch pipe.
I ,
03UOJ2-016
Tie-rod end
1. Remove the cotter pin.
Caution
l Do not damage the dust boot.
2. Loosen the nut and disconnect the tie-rod end with the SST.
I I
03UOJ2-017
52-l 1

TRANSAXLE J2
Clutch Housing and Transaxle Case Components
Caution
l Do not remove an oil seal if not necessary.
1. Disassemble in the order shown in the figure, referring to Disassembly Note.
ACE
1. Bearing outer race (Primary shaft) 19. Oil seal (differential)
2. Oil seal Replacement (On-vehicle) . . . . . . . . . page J2-16
3. Bearing outer race (Secondary shaft) 20. Bearing outer race (differential)
Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16 Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
4. Funnel 21. Reverse lever shaft
5. Guide plate 22. Reverse lever
6. Change arm 23. Drain plug and washer
7. Roll pin 24. Neutral switch and gasket
Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16 25. Bearing outer race (transaxle case)
8. Change rod assembly Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
9. Boot 26. Diaphragm spring
10. Spring 27. Adjust shim
11. Reverse gate 28. Bearing outer race (differential)
12. Selector Disassembly Note . . . . . . . . . . . . . . . . . . . . . page J2-16
13. Oil seal 29. Adjust shim(s)
14. Bleeder cover 30. Oil seal (differential)
15. Bleeder Replacement (On-vehicle) . . . . . . . . . page J2-16
16. Speedometer driven gear assembly 31. Back-up light switch
Inspection ..,.,,.,......,................... page J2-24 32. Oil passage
17. Driven gear 33. Joint
18. Gear case 34. Change rod
52-l 5

TRANSAXLE
03UOJ2-02
03UOJ2-0:
I IO
03UOJ2-031
1
03UOJ2-121
Caution
l Do not damage the dust boots.
4. Remove the clinch bolt and pull the lower arm downward.
Separate the knuckle from the lower arm ball joint.
5. Loosen the nut and disconnect the tie-rod end with the
SST.
Caution
l Do not subject the tripod joint to shock when remov-
ing the driveshaft.
6. Disconnect the driveshaft from the transaxle by prying with
a bar between the outer ring and the transaxle.
7. Suspend the driveshaft with a rope.
8. Remove the oil seal with a screwdriver.
Note
l Tap in until the oil seal installer contacts the case.
l Coat the oil seal lip with transaxle oil.
9. Tap the new oil seal into the transaxle case with the SST.
10. Replace the driveshaft end clip with a new one. Insert the
driveshaft with the end-gap of the clip facing upward.
I I
I 03UOJ2-032
J2-17

TRANSAXLE J2
Clutch Housing and Transaxle Case Components
1. Select the adjust shim(s), referring to Bearing Preload Adjustment.
2. Assemble in the order shown in the figure, referring to Assembly Note.
3. Verify that the bearing preload is satisfied after assembly, referring to Bearing Preload.
-s
APPLY SPECIFIED OIL TO INDIVIDUAL PARTS EXCEPT SWITCHES
&II N.m (SO-110 cm-kg, SO-95 In-lb)
20-29
P-3,
@NEW=
O-RING, I
14-22) 11
R N.m (120-160 cm-kg,
104-l 39 in-lb)
A
=SELECTlVE ROLL PIN NE
(120-140 cm-kg,
SELECTIVE 20-29 (2-3, 14-22)
N.m (m-kg,
??I 1
1. Change rod 16. Oil seal
2. Joint
3. Oil passage
4. Back-up light switch
5. Oil seal
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35
6. Adjust shim(s)
Bearing preload adjustment . . . . . page J2-32
Bearing preload . . . . . . . . . . . . . . . . . . . . . . . . page J2-36
7. Bearing outer race
8. Adjust shims
Bearing preload adjustment . . . . . page J2-32
Bearing preload . . . . . . . . . . . . . . . . . . . . . . . . page J2-36
9. Diaphragm springs
Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35 Assembly Note . . . . . . . . . . . . . . . . . . . . . . . . . . page J2-35
17. Gear case
18. Driven gear
19. Speedometer driven gear assembly
20. Bleeder
21. Bleeder cover assembly
22. Oil seal
23. Selector
24. Reverse gate
25. Spring
26. Boot
Assembly Note ,.,....................... page J2-35
27. Change rod assembly
28. Roll pin
10. Bearing outer races
11. Neutral switch and gasket
12. Drain plug and washer
13. Reverse lever
14. Reverse lever shaft
15. Bearing outer race 29. Change arm
30. Guide plate
31, Funnel
32. Bearing outer race
33. Oil seal
34. Bearing outer race
J2-31

TRANSAXLE
i
03UOJ2-078
-
Thickness
0.10 (0.004)
0.20 (0.008)
0.25 (0.010)
0.30 (0.012)
0.35 (0.014)
0.40 (0.016)
0.45 (0.018)
050 (0020)
0.55 (0.022)
0 60 (0.024)
0.65 (0.026)
03UOJZO7 mm (in)
0.70 (0.028)
0.75 (0.030)
0.80 (0.031)
0.85 (0.033)
0.90 (0.035)
0.95 (0.037)
1.00 (0.039)
1.05 (0.041)
1.10 (0.043)
1.15 (0.045)
1.20 (0.047)
03UOJ2-081
, T/RAkiXiE /CA/SE/////,///
BEARING OUTER RACE
,ADJUSTMENT SHIM
__________
po3u0J2-08i
Caution
l Measure the gap around the entire circumference
of the selector
13. Use a feeler gauge to measure the gap in the selector for
the differential.
14. Add 0.15mm (0.0059 in) to the measured clearance and
select the combination of shims closest in value to that meas-
urement.
Note
l Use a maximum of two shims.
See the table below for available shim sizes.
Example: 0.32mm (0.013 in)
0.32mm (0.013 in) + 0.15mm (0.006 in) = 0.47mm
(0.019 in).
So the nearest shim (on the thick side) to 0.47mm
(0.019 in) is 0.50mm (0.020 in).
15. Remove the SST and the transaxle case.
16. Remove the selectors, the primary shaft assembly and the
-differential.
17. Remove the bearing outer races.
Assembly note
Oil seals
1. Apply transaxle oil to outer periphery.
2. Install the new oil seals with the SST.
Diaphragm spring
1. Install the diaphragm spring as shown in the figure.
Boot
1. Install the boot with the drain hole facing downward.
03UOJ2-082
J2-35