MITSUBISHI ENDEAVOR 2004 Service Repair Manual

Fig. 85: Checking ABS Sensor Connector D
-15 (Step 14)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are TCL/ASC-ECU connector A-32, intermediate connector C-32 and
ABS sensor < rear: LH > connector D-15 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16.
NO: Open or short circuit may be present in the rear left ABS sensor
circuit. Repair the wiring harness between TCL/ASC-ECU connector A-
32 (terminals 6 and 7) and rear left ABS sensor D-10 (terminals 1 and 2).
Then go to Step 16
.
STEP 15. Recheck for diagnostic trouble code.
Check again if the DTC is set.
1. Turn the ignition switch to the &#34;ON&#34; position.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

2. Erase the DTC.
3. Turn the ignition switch to the &#34;LOCK&#34; (OFF) position.
4. Turn the ignition switch to the &#34;ON&#34; position.
5. Check if the DTC is set.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 86: Recheck For Diagnostic Trouble Code

Courtes
y of MITSUBISHI MOTOR SALES OF AMERICA
.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

6. Turn the ignition switch to the &#34;LOCK&#34; (OFF) position.
Q: Is DTC C1201, C1206, C1211 or C1216 set?
YES: Replace the hydraulic unit (integrated with TCL/ASC-ECU). Then
go to Step 16.
NO: It can be assumed that this malfunction is intermittent. Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
.
STEP 16. Recheck for diagnostic trouble code.
Check again if the DTC is set.
1. Turn the ignition switch to the &#34;ON&#34; position.
2. Erase the DTC.
3. Turn the ignition switch to the &#34;LOCK&#34; (OFF) position.
4. Turn the ignition switch to the &#34;ON&#34; position.
5. Check if the DTC is set.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 87: Recheck For Diagnostic Trouble Code

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

6. Turn the ignition switch to the &#34;LOCK&#34; (OFF) position.
Q: Is DTC C1201, C1206, C1211 or C1216 set?
YES: Go to Step 1.
NO: The procedure is complete.
DTC C1223: SUSPENSION OF SNSR. ACTIVE CHECK
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 88: G And Yaw Rate Sensor Circuit Diagra
m
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 89: Identifying Connectors: A
-32, C
-24, C
-04, C
-31, C101, B
-18, C
-36, C
-
214, C
-215

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CIRCUIT OPERATION
CAUTION: If there is any problem in the CAN bus lines, an
incorrect dia
gnostic trouble code ma
y be set. Prior to
this diagnosis, diagnose the CAN bus lines.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

The TCL/ASC-ECU gathers information regarding lateral and longitudinal
accelerations and yaw rate, through the CAN bus line from the G and yaw rate
sensor. TCL/ASC DTC SET CONDITIONS The TCL/ASC-ECU activates the G and yaw rate sensor via a CAN bus line in
order to diagnose the sensor whenever the ignition switch is turned on. If the G and
yaw rate sensor does not respond to this request, this DTC will be set. TROUBLESHOOTING HINTS (The most likely causes for these DTC are to set are:)
Current trouble
The CAN bus line is defective. Damaged connector(s) The G and yaw rate sensor is defective. The TCL/ASC-ECU is defective.
Past trouble Carry out diagnosis with particular emphasis on connector(s) or wiring harness
between the TCL/ASC-ECU and the G and yaw rate sensor. For diagnosis
procedures, refer to HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
.
DIAGNOSIS Required Special Tools:
MB991958: Scan Tool (MUT-III Sub Assembly)
MB991824: Vehicle Communication Interface (V.C.I.) MB991827: MUT-III USB Cable MB991910: MUT-III Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.
CAUTION: To prevent damage to scan tool MB991958,

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

1. Connect scan tool MB991958 to the data link connec
tor. always turn the ignition switch to the
&#34;LOCK&#34; (OFF) position before connecting or
disconnecting scan tool MB991958.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 90: Connecting Scan Tool MB991958 To Data Link Connector

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor