MITSUBISHI ENDEAVOR 2004 Service Manual PDF

Fig. 43: Measuring Resistance At ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Q: Does continuity exist?
YES (Continuity exists between terminal 9 or terminal 10 and body
ground): Go to Step 11 .
YES (Continuity exists between terminal 26 or terminal 16 and body
ground): Go to Step 12 .
YES (Continuity exists between terminal 11 or terminal 17 and body
ground): Go to Step 13 .
YES (Continuity exists between terminal 28 or terminal 27 and body
ground): Go to Step 14 .
NO: Go to Step 10.
STEP 10. Measure the resistance at ABS-ECU connector A-02.
1. Disconnect the connector A-02, and connect special tool ABS Check
Harness (MB991970) to the wiring harness-side connector.
2. Measure the resistance between the relevant signal and ground terminals
in the ABS sensor circuit.
DTC C1201 is set: Between signal terminal 9 and ground terminal 10 DTC C1206 is set: Between signal terminal 26 and ground terminal
16 DTC C1211 is set: Between signal terminal 11 and ground terminal
17 DTC C1216 is set: Between signal terminal 28 and ground terminal
27
Standard Value: 1.24 - 1.64 kohm NOTE: Do not connect special tool ABS Check Harness
(MB991970) to the ABS-ECU.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 44: Measuring Resistance At ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Q: Is the resistance between terminals 16 and 26, 9 and 10, 27 and 28, or
11 and 17 within the standard value?
YES (When resistance between all terminals are within the standard
value): Go to Step 15 .
NO (When resistance between terminals 9 and 10 is not within the
standard value): Go to Step 11.
NO (When resistance between terminals 16 and 26 is not within the
standard value): Go to Step 12 .
NO (When resistance between terminals 11 and 17 is not within the
standard value): Go to Step 13 .
NO (When resistance between terminals 27 and 28 is not within the
standard value): Go to Step 14 .
STEP 11. Check ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-31 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 45: Checking ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 46: Checking ABS Sensor Connector A
-31
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-31 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the front right ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 9 and 10) and front right ABS sensor A-31 (terminals 2 and 1).
Then go to Step 16 .
STEP 12. Check ABS-ECU connector A-02 and ABS sensor < front: RH >
connector A-14 for loose, corroded or damaged terminals, or terminals
pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 47: Checking ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 48: Checking ABS Sensor Connector A
-14
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are ABS-ECU connector A-02 and ABS sensor < front: LH >
connector A-14 damaged?
YES: Repair or replace the damaged component(s). Then go to Step 16 .
NO: Open or short circuit may be present in the front right ABS sensor
circuit. Repair the wiring harness between ABS-ECU connector A-02
(terminals 16 and 26) and front left ABS sensor A-14 (terminals 1 and 2).
Then go to Step 16 .
STEP 13. Check ABS-ECU connector A-02, intermediate connector C-32
and ABS sensor < Rear: RH > connector D-10 for loose, corroded or
damaged terminals, or terminals pushed back in the connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 49: Checking ABS
-ECU Connector A
-02
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor

Fig. 50: Checking D
-15 Harness Connector

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BRAKES Anti-Lock Braking System (ABS) - Endeavor