coil MITSUBISHI LANCER 2005 Owner's Manual

EMISSION CONTROL <MPI>
ENGINE AND EMISSION CONTROL17-5
EMISSION CONTROL <MPI>
GENERAL INFORMATIONM1173000100370
The emission control system consists of the following
subsystems:•Crankcase emission control system
•Evaporative emission control system
•Exhaust emission control system
EMISSION CONTROL DEVICE
REFERENCE TABLE
M1173006600135
SERVICE SPECIFICATION(S)M1173000300288
Items Name Specification
Crankcase emission control
systemPositive crankcase ventilation
(PCV) valveVariable flow type
(Purpose: HC reduction)
Evaporative emission control
systemCanister
Purge control solenoid valveEquipped
Duty cycle type solenoid valve
(Purpose: HC reduction)
Exhaust emission control system Air-fuel ratio control device - MPI
systemOxygen sensor feedback type
(Purpose: CO, HC, NOx reduction)
Exhaust gas recirculation system
•EGR valve
•EGR control solenoid valveEquipped
Single type
Duty cycle type solenoid valve
(Purpose: NOx reduction)
Catalytic converter Monolith type
(Purpose: CO, HC, NOx reduction)
Related parts Crankcase
emission
control
systemEvaporative
emission
control
systemAir/fuel ratio
control
systemCatalytic
converterExhaust gas
recirculation
system
PCV valve
×
Purge control solenoid valve
×
MPI system component
××
Catalytic converter
×
EGR valve
×
EGR control solenoid valve
×
Items Standard value
Purge control solenoid valve coil resistance (at 20°C) Ω30 − 34
EGR control solenoid valve coil resistance (at 20°C) Ω29 − 35

GENERAL INFORMATION
FRONT SUSPENSION33-2
GENERAL INFORMATION
M1332000100407
The front suspension is a McPherson strut with coil
spring. The shock absorber is gas-filled hydraulic
double-acting type.
CONSTRUCTION DIAGRAM
SPECIFICATIONS
COIL SPRING
NOTE: .
•The*mark indicates optional item.
AC304023
AC304022
AC304754
Lower arm assembly
Front axle No.1
crossmember Stabilizer bar
Strut (shock absorber) Coil spring
AB
<Comfort>
Strut cover Strut damper
<Sport>Strut damper
Item Sedan Wagon
Comfort Sport Comfort Sport
Wire diameter mm 13 13 13 <1600-M/T>
14 1600-A/T,
2000>14
13 <1600>
*
14 <2000>*
Average diameter mm 160 160 160 160
Free length mm 330 321 330 <1600-M/T>
338 <1600-A/T>
338 <2000>314 <1600>
321 <2000>
330 <1600>
*
338 <2000>*

SPECIAL TOOLS
FRONT SUSPENSION33-4
SPECIAL TOOLS
M1332000600297
Tool Number Name Use
MB991004 Wheel alignment gauge
attachmentWheel alignment
measurement <Vehicles
with aluminium wheels>
A: MB991237
B: MB991238A: Spring compressor
body
B: Arm setCoil spring compression
MB991680
A: MB991681
B: MB991682Wrench set
A: Wrench
B: SocketStrut assembly
disassembly and
reassembly
MB991006 Preload socket Lower arm ball joint
rotation starting torque
check
MB990800 Ball joint remover and
installerLower arm ball joint cover
installation
MB991004
MB991237
A
B
MB991680
A
B
MB991006
MB990800

STRUT ASSEMBLY
FRONT SUSPENSION33-8
DISASSEMBLY AND REASSEMBLYM1332001300329
AC300065AC300065
9
101
2
3
4
5
6
60 ± 10 N·m
AC
8
7
<Sport><Comfort>
Disassembly steps
<<A>> >>B<<1. Strut nut (self-locking nut)
2. Strut insulator
3. Strut bearing
>>A<<4. Spring upper seat
5. Strut damper <Sport>6. Strut cover <Comfort>
7. Strut damper <Comfort>
8. Coil spring
9. Spring lower pad<<B>>10. StrutDisassembly steps (Continued)

STRUT ASSEMBLY
FRONT SUSPENSION33-9
DISASSEMBLY SERVICE POINTS
<<A>> STRUT NUT (SELF-LOCKING NUT)
REMOVAL
CAUTION
•Install special tool arm set (MB991238) evenly,
and so that the maximum length will be
attained within the installation range.
•Do not use an impact wrench to tighten the
bolt of special tool spring compressor body
(MB991237), otherwise the special tool will
break.
1. Use following special tools to compress the coil
spring.
•MB991237: Spring Compressor Body
•MB991238: Arm Set
WARNING
Do not use an impact wrench to remove the
strut nut (self-locking nut). Vibration of the
impact wrench will cause special tools
(MB991237 and MB991238) to slip and cause
personal injury.
2. Use following special tools to secure the strut, and
then remove the strut nut (self-locking nut).
•MB991681: Wrench
•MB991682: Socket
<<B>> STRUT DISPOSAL
WARNING
Wear goggles when drilling to protect your
eyes from flying metal debris.
The gas must be discharged from the strut before
discarding it. Place the strut horizontally with its
piston rod extended. Then drill a hole of
approximately 3 mm in diameter at the location
shown in the illustration and discharge the gas.
REASSEMBLY SERVICE POINTS
>>A<< SPRING UPPER SEAT
INSTALLATION
If the spring upper seat peeled off the pad, adhere
the seat and the pad with a double-sided tape.
AC001085 AB
MB991238
MB991237
AC006091 AB
MB991681 MB991682
AC001087
AC304396AB
Seat
Pad

STRUT ASSEMBLY
FRONT SUSPENSION33-10
>>B<< STRUT NUT (SELF-LOCKING NUT)
INSTALLATION
1. Ensure that the bearing is seated correctly.
CAUTION
Do not use an impact wrench to tighten the bolt
of special tool spring compressor body
(MB991237), otherwise the special tool will break.
2. Install following special tools to the strut assembly
same as its removal.
•MB991237: Spring Compressor Body
•MB991238: Arm Set
3. While the coil spring is being compressed by the
special tools, temporarily tighten the strut nut
(self-locking nut).
4. Align the hole in the strut spring lower seat with
the hole in the spring upper seat.
NOTE:
Using a rod as shown facilitates the alignment.5. Align lower end of the coil spring with the groove
in the spring lower seat, and then loosen the
special tools.CAUTION
Do not use an impact wrench to tighten the
self-locking nut, otherwise the strut nut
(self-locking nut) will be damaged.
6. Using following special tools, tighten the strut nut
(self-locking nut) to 60 ± 10 N⋅m.
•MB991681: Wrench
•MB991682: Socket
INSPECTIONM1332001400188
•Check the strut bearing for wear or rust.
•Check the rubber parts for damage or
deterioration.
•Check the coil spring for deformation,
deterioration or damage.
•Check the strut for deformation.
AC001085 AB
MB991238
MB991237
AC006091 AB
Rod
AC006091 AB
MB991681 MB991682

GENERAL INFORMATION
REAR SUSPENSION34-2
GENERAL INFORMATION
M1341000100353
A trailing arm type multi-link suspension has been
adopted as the rear suspension. The shock absorber
is a hydraulic, cylindrical double-acting type.
CONSTRUCTION DIAGRAM
AC304024AB
Shock absorber
Coil spring
Trailing arm bushing Lower arm assembly Control link Trailing armUpper arm assembly
Stabilizer barRear shock
absorber damper<Sedan>
<Wagon>
<Comfort>
Rear shock
absorber damper
Rear shock
absorber cover
AC304025AB
Shock absorber
Trailing arm bushing Control link Trailing armStabilizer bar
<Sport>
Coil spring
Lower arm assembly
Rear shock
absorber damper Upper arm assembly

SERVICE SPECIFICATIONS
REAR SUSPENSION34-3
SPECIFICATION
COIL SPRING
SERVICE SPECIFICATIONS
M1341000300409
LUBRICANT
M1341000400172
Item Sedan Wagon
Comfort Sport Comfort Sport
Wire diameter mm 10 10 10 10
Average diameter mm 78 − 90 78 − 90 78 − 90 78 − 90
Free length mm 359 331 377 368
Item Standard value
Camber (Difference between right and left within 30')
−0°40' ± 30'
Toe-in At the centre of tyre tread mm 3 ± 2
Toe-angle (per wheel) 0°08' ± 05'
Thrust angle 0°00' ± 0°09'
Control link pillow ball bushing rotation starting torque <Sport> N⋅m0.5 − 3.0
Upper arm pillow ball bushing rotation starting torque <Sport> N⋅m0.5 − 3.0
Lower arm pillow ball bushing rotation starting torque N⋅m0.5 − 3.0
Protruding length of stabilizer link bolt mm 6 − 8
Stabilizer link ball joint continuous rotating torque N⋅m0.5 − 1.5
Item Specified lubricant Quantity
Stabilizer link ball joint (inside of dust cover) Multipurpose grease SAE J310, NLGI No.2
or equivalentAs required

ON-VEHICLE SERVICE
REAR SUSPENSION34-5
ON-VEHICLE SERVICE
REAR WHEEL ALIGNMENT CHECK AND
ADJUSTMENT
M1341011000372
Measure wheel alignment with an alignment
equipment on level earth.
The rear suspension, wheels, and tyres should be
serviced to the normal condition prior to wheel
alignment measurement.
CAMBER
Standard value: -0° 40' ± 30' (Left/right
deviation within 30')
CAUTION
Never subject the wheel bearings to the vehicle
load when the rear wheel hub nuts (self-locking
nuts) or special tool wheel alignment gauge
attachment (MB991014) are loosened.
NOTE:
For vehicles with aluminium wheels, attach the
camber/caster/kingpin gauge to the trailing arm
spindle by using special tool wheel alignment gauge
attachment (MB991014). Tighten the special tool to
the same torque 175
± 25 N⋅m as the rear wheel hub
nut (self-locking nut). MB990947 Lower arm bushing arbor Trailing arm bushing
removal and press-fitting
MB991816 Bushing remover and
installer base
MB990890 Rear suspension bushing
base
A: MB991237
B: MB991239A: Spring compressor
body
B: Arm setCoil spring compressing Tool Number Name Use
MB990947
MB990890
MB991237
A
B
AC001079
MB991014
AG
<Vehicles with aluminium wheels>

SHOCK ABSORBER ASSEMBLY
REAR SUSPENSION34-15
SHOCK ABSORBER ASSEMBLY
REMOVAL AND INSTALLATIONM1341002500261
CAUTION
*: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the earth in the unladen condition.
Pre-removal and Post-installation Operation
•Centre Luggage Floor Lid <Wagon> Removal and
Installation
•Centre Luggage Floor Box <Wagon> Removal and
Installation
AC304794AB
44 ± 5 N·m
2413
5
95 ± 15 N·m*95 ± 15 N·m*
N
Removal steps
>>B<<1. Stabilizer link connection
<<A>>2. Lower arm bolt
3. Coil spring nut4. Coil spring bolt>>A<<5. Shock absorber assemblyRemoval steps (Continued)