tow MITSUBISHI LANCER 2005 Owner's Manual

WINDSHIELD WIPER AND WASHER
EXTERIOR51-24
NOTE: For removal and installation of the wiper and
washer switch, refer to GROUP 54A, Column switch
P.54A-87.
REMOVAL SERVICE POINT
<<A>> WINDSHIELD WIPER MOTOR
ASSEMBLY REMOVAL
1. Remove the windshield wiper motor assembly
mounting bolt.
CAUTION
Be careful not to damage the windshield glass
when the windshield wiper motor assembly is
removed.
2. Use the fiat-tipped screwdriver to disengage the
link between the windshield wiper motor assembly
and the link assembly to remove the windshield
wiper motor assembly.
INSTALLATION SERVICE POINTS
>>A<< WIPER BLADE INSTALLATION
CAUTION
The driver's side wiper blade is not warped.
When installing the passenger's wiper blade, check
that the backing inside the wiper blade is warped
toward the wiper arm.
>>B<< WIPER BLADE ASSEMBLY
INSTALLATION
Install the wiper blade at the specified position
(standard value).
Standard value (A): 34 ± 5 mm
Wiper blade assembly removal steps
>>B<<1. Wiper blade assembly
>>A<<2. Wiper blade
Windshield wiper motor and link
assembly removal steps
3. Cover
4. Wiper arm
5. Hood weather strip
6. Front deck garnish (passenger's side)
7. Front deck garnish (driver's side)
<<A>>8. Windshield wiper motor assembly
9. Link assembly
Washer hose removal steps
•Front splash shield (Refer to GROUP
42, Fender P.42-6)
10. Rear washer hose <Wagon>
11. Front washer hoseWindshield washer nozzle removal
steps
•Connection of front washer hose
11. Washer nozzle
Washer tank and washer motor
removal steps
•Side undercover (RH)
•Front splash shield (Refer to GROUP
42, Fender P.42-6)
•Connection of front washer hose and
rear washer hose
12. Washer tank assembly
13. Front washer motor
14. Rear washer motor <Wagon>
AC304411AB
Windshield wiper
motor assembly
Link assembly
connection
Flat-tipped screwdriverAC101090AD
Wiper bladeBacking
BackingA
A
Section A – A
Wiper
bladeBacking
AC000427
A
A
Front deck garnish terminalAD

IGNITION SWITCH
CHASSIS ELECTRICAL54A-28
REMOVAL SERVICE POINT
<<A>> STEERING LOCK CYLINDER
REMOVAL
1. Insert the key in the steering lock cylinder and turn
it to the "ACC" position.
2. Using a small Phillips head screwdriver, pull the
steering lock cylinder toward you.
INSPECTIONM1544009700203
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-201 without
removing the ignition switch. Then check the
continuity.
KEY REMINDER SWITCH CONTINUITY
CHECK
Disconnect key reminder switch connector C-202
without removing the ignition switch and key
reminder switch. Then check the continuity.
AC304831AB
Locking pin
AC304833AB
Switch
position Tester
connectionSpecified
condition
"LOCK" (OFF) 1 − 2, 1 − 3,
1 − 4, 1− 5,
1 − 6, 2 − 3,
2 − 4, 2− 5,
2 − 6, 3 − 4,
3 − 5, 3 − 6,
4 − 5, 4 − 6,
5 − 6Open circuit
"ACC" 1 − 6 Less than 2
ohms
"ON" 1 − 2, 1 − 4,
1 − 6, 2 − 4,
2 − 6, 4 − 6Less than 2
ohms
"START" 1 − 2, 1 − 5,
2 − 5Less than 2
ohms
Status of
ignition keyTester
connectionSpecified
condition
Removed 4 − 6 Less than 2
ohms
Inserted 4 − 6 Open circuit
AC304834AB