service MITSUBISHI LANCER 2006 Workshop Manual

HOOD
BODY42-3
HOOD
ON-VEHICLE SERVICE
ADJUSTMENT OF CLEARANCE AROUND
HOOD
M1421007200129
AC005945
ADJUSTMENT OF ALIGNMENT OF HOOD
STEPPED PORTION AND HOOD
STRIKER
M14210073 0012 6
AC005947
ADJUSTMENT OF HOOD HEIGHT
M14210074 0012 3
Y0215AU
X0424CA
AC005948
AB
Section A – A A
A
Hood
Hood bumper
17 mm
Ro
t a te t he hood bu mper by using arrow mark o n the
hood bu
mpe r as a g u ide t o adju s t the hood h e ight . If
the hoo
d bumper is rot a te d just one turn, th e hood
heigh
t cha nges by approximately 3 mm.

FENDER
BODY42-7
REMOVAL SERVICE POINT
<<A>> SIDE TURN-SIGNAL LAMP
REMOVAL
AC005980AC005980
Front of vehicleSide turn-signal lamp
MB990784
AB
Use sp ecial to ol orn a men t remover (MB9907 84) to
prize out th
e t ab from the fender , and re move the
side
turn
− signal lamp .
INSTALLA T ION SER VICE POINT
>>A<< SIDE TURN-SIGNAL LAMP
INST
ALLA TION
AC005719
Fender panel Hook
Claw
Fender panel
: Front of vehicle
AE
En gage t he claw with t he fend er p anel, and inst all
the side tu
rn-signal lamp.

WINDOW GLASS
BODY42-10
WINDOW GLASS
ADHESIVEM1422000500081
ItemSpecified adhesive
Windshield3M ATD Part No.8609 Super Fast Urethane Auto Glass
Sealant or equivalent
3M ATD Part No.8608 Super Fast Urethane Primer or
equivalentRear window glass
Quarter window glass
Tailgate window glass
SPECIAL TOOLS
M1422000600293
ToolNumberNameUse
MB990480
MB990480Gl as s h o l de rRemoval and inst a llat i on of wind ow glass
MB990784
MB990784Ornament removerRemoval of rea r window lower mo ulding
WI NDOW REP A IR
M14220056 0002 7
The windshield, rear wind ow glass, q uarter window
glass an
d t a ilg ate win dow gla ss a r e att a ched by an
urethan
e-base adhe sive to the wind ow frame . This
adhesive provides improv
ed glass hold i ng a nd seal
-
ing, and also g i ve s bod y op ening s a g r eater struc-
tural strength.
ITEMS
NameRemark
Adhesive3M ATD Part No.8609 Super Fast Urethane Auto Glass Sealant or
equivalent
Primer3M ATD Part No.8608 Super Fast Urethane Primer or equivalent
SpacersAvailable as service part
DamAvailable as service part
Anti-rust solvent (or Tectyl
506T.Valvoline Oil Company)For rust prevention
Isopropyl alcoholFor grease removal from bonded surface
Steel piano wireDia. × length... 0.6mm × 1m For cutting adhesive
Glass adhesive knifeFor cutting adhesive
Adhesive gunFor pressing-out adhesive

WINDOW GLASS
BODY42-14
CAUTION•
ACX00476AB
Be careful not to remove more adhesive than is
necessary.
•Be careful also not to damage the paintwork
on the body surface with the knife. If the
paintwork is damaged, repair the damaged
area with repair paint or anti-rust agent.
6. Use a knife to cut away the remaining adhesive so
that the thickness is within 2 mm around the entire
circumference of the body flange.
7. Finish the flange surfaces so that they are smooth.
CAUTION
Allow the cleaned area to dry for at least three
minutes. Do not touch any surface that has been
cleaned.
8. When reusing the windshield, remove the adhesive still adhering to the windshield, and
clean with isopropyl alcohol.
9. Clean the body side in the same way.
INSTALLATION SERVICE POINTS
>>A<< WINDSHIELD
SPACER/SPACER/GLASS STOPPER/WIN
-
DOW DAM/WINDSHIELD MOULDING
INSTALLATION
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
1. Use isopropyl alcohol to degrease the inside and outside of the windshi eld and the body flanges.

WINDOW GLASS
BODY42-18
REMOVAL SERVICE POINTS
<<A>> REAR WINDOW LOWER MOULD-
ING REMOVAL
CAUTION
If the drip moulding has become warped, it
should not be reused.
AC006073AB
MB990784
Use special tool ornament remover (MB990784) to
lever out the moulding.
<<B>> REAR WINDOW GLASS REMOVAL
Removal the rear window glass using the same pro-
cedure as for the windshield. (Refer to P.42-12.)
INSTALLATION SERVICE POINTS
>>A<< GLASS STOPPER/WINDOW
DAM/REAR WINDOW UPPER MOULD
-
ING/REAR WINDOW GLASS INSTALLA-
TION
1. When replacing the rear window glass,
temporarily set the rear window glass against the
body, and place a mating mark on the rear
window glass and body.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and outside of the rear window glass and the body
flanges.
CAUTION
•The primer strengthens the adhesive, so be
sure to apply it evenly around the entire cir
-
cumference. However, a too thick application
will weaken the adhesive.
•Do not touch the coated surface.
3. Soak a sponge in the primer, and apply evenly to the rear window glass and the body in the
specified places.
4. Allow the rear window glass to dry for at least 3 minutes after applying primer.
>>A<<9.Window dam
>>A<<10.Glass stopper
Removal steps (Continued)

WINDOW GLASS
BODY42-21
REMOVAL SERVICE POINT
<<A>> QUARTER WINDOW GLASS
REMOVAL
AC103600ADCloth tape
1.App l y cloth t a pe to p r otect the q uarter win dow
glass.
AC002060
2.Use gla ss adhesive knife to cut a w a y adh esive.
AC301614AB
Glass adhesive knife
CAUTION
Inserting the adhesive knife too deeply into wind-
shield adhesive may damage quarter window
glass.
3. Keep the glass adhesive knife at right angles with
body flange (from inside the vehicle), and put the
blade at body flange. Then cut away adhesive
along the body flange.
AC103605 AD
MB990480
4. Make mating marks on the quarter window glass
and body.
5. Use special tool glass holder (MB990480) to
remove the quarter window glass.
ACX00476 AB
CAUTION
•Be careful not to remove more adhesive than
is necessary.
•Be careful also not to damage the paintwork
on the body surface with the knife. If the
paintwork is damaged, repair the damaged
area with repair paint or anti-rust agent.
6. Use a knife to cut away the remaining adhesive so
that the thickness is within 2 mm around the entire
circumference of the body flange.
7. Finish the flange surfaces so that they are smooth.
CAUTION
Allow the cleaned area to dry for at least three
minutes. Do not touch any surface that has been
cleaned.
8. When reusing the quarter window glass, remove
the adhesive still adhering to the quarter window
glass, and clean with isopropyl alcohol.
9. Clean the body side in the same way.

WINDOW GLASS
BODY42-22
INSTALLATION SERVICE POINTS
>>A<< GASKET/CLIP/DUAL LOCK FAS-
TENER INSTALLATION
1. Carry out the following procedure to re-install quarter window glass.
CAUTION
Do not forget gasket.
(1) Fit clips into body.
AC103606 AC
Cut off these convex parts
(2) Cut away clip fitting convex on quarter window
glass.
NOTE: Convex gets broken when quarter win-
dow glass is removed.
CAUTION
Leave the degreased parts for 3 or more minutes
to dry well, before starting on the next step. Do
not touch the degreased parts.
2. Use isopropyl alcohol to degrease the inside and
outside of the quarter window glass and the body
flanges.
AC304793AB
Dual lock fastener
Install the dual lock fastener
with aligning it onto the bumps
of the body flange.
3. Assemble the dual lock fastener according to the standard location of the body flange.
4. Assemble the dual lock fastener to the quarter window glass relative to the body flange dual lock
fastener.
>>B<< QUARTER WINDOW GLASS
INSTALLATION
Remove the quarter window glass using the same
procedure as for the windshield removal (Refer to
P.42-12).

DOOR
BODY42-27
ON-VEHICLE SERVICE
DOOR FIT ADJUSTMENT
M1423001100175
CAUTION
•Attach protection tape to the fender and door
edges where the hinge is installed.
•Do not rotate special tool door adjusting
wrench (MB991164) with a torque of over 98
N
⋅m
AC000592
MB990900
or
MB991164
AB
1. Use the special tool door adjusting Wrench (MB990900 or MB991164) to loosen the hinge
mounting bolts on the body side, and then adjust
the clearance around the door so that it is uniform
on all sides.
2. If a door is not flush with its surrounding panels,
loosen the door-side d oor hinge mounting bolts
and obtain the flushness by moving the door.
NOTE:
AC206498
Washer Bolts
Washer
Door hinge
AF
Weld point
Weld point
If the door hinge mounting bolt washers are
welded, grind off the welding according to the pro
-
cedure below beforehand.
.
1. Remove the door hinge (Refer to P.42-31).
2. Use a chisel or grinder to release the door
hinge mounting bolt washers, which are
welded to the door hinge.
3. On completion, paint the affected area with a suitable touch-in brush to prevent corrosion.
4. Install the door hinge (Refer to P.42-31).
3. When the door is stiff to lock and unlock
AC006109AB
Temporary
bolts Striker
MB990939
(1) Adjustment by using the striker (toward the
inside of the vehicle and vertical direction)
Install a temporary bolt instead of the striker
mounting bolts, and use special tool brass bar
(MB990939) and a hammer to tap the bolt to
the desired direction.
AC006110
Striker MB990211
MB990243
AB
(2) Adjustment by using the striker (toward the
outside of the vehicle)
Use special tools slide hammer (MB990211)
and body puller (MB990243) to pull the striker
toward the outside of the vehicle.
AC006111AB
Shim
Striker
(3) Adjustment by using shims (forward and rearward)
Increase or decrease the number of shims so
that the striker engages with the door latch
properly.

DOOR
BODY42-32
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
AC305098AB
Striker centreStriker Latch centre
Latch
+1.5 mm
-1.5 mm
Align the centre o f the striker and latch within ±1.5
mm,
and inst
all.
INSPECTION
M1423 0060 0032 2
DOOR SWITCH CHECK
AC211414
123
AC
Switch
positionTester
connectionSpecified
condition
Released (ON)1 − switch body,
2
− switch body,
3
− switch body
Less than 2
ohms
Depressed
(OFF)1 − switch body,
2
− switch body,
3
− switch body
Open circuit
DOOR GLASS AND REGULA T O R
REMOVA L AND INST ALLA TIONM14290013 0031 5
Post-installation Operation
•Door Window Glass Adjustment (Refer to P.42-28).
AC212124AB
<FRONT DOOR> <REAR DOOR>
1
23
12
3
4
5
6

DOOR
BODY42-34
REMOVAL SERVICE POINTS
<<A>> WINDOW REGULATOR ASSEM-
BLY/POWER WINDOW REGULATOR
MOTOR ASSEMBLY REMOVAL
1. Remove the door window glass installation bolts.
CAUTION
If film or others are adhered to the door window
glass, attach special tool window glass holder
(MB990480) to the outside of the glass to prevent
the film from peeling off.
AC100009AB
MB990480
2. Lift the door window glass, and attach special tool
window glass holder (MB990480) to the glass as
shown to prevent the glass from falling.
3. Remove the window regulator assembly and power window motor assembly
<<B>> CENTRE SASH UPPER REMOVAL
AC000602
Door outer
opening
weatherstrip
Door centre
sash
AB
1. Remove the door outer opening weatherstrip from the centre sash upper only.
2. Remove the centre sash upper mounting screws, and then remove the centre sash upper from the
door panel.
INSTALLATION SERVICE POINTS
>>A<< CENTRE SASH UPPER INSTALLA-
TION
Securely insert the centre sash upper into the win-
dow rear sash (door).
>>B<< WINDOW REGULATOR
ASSEMBLY/POWER WINDOW
REGULATOR MOTOR ASSEMBLY
INSTALLATION
Y1536AU
Y1476AUAC100010 AB
<FRONT DOOR>
<REAR DOOR>
1 2
3 4
5
6 7
1 2
3 4
56
When installing the window regulator assembly,
tighten the bolts to the specified torque in the order
shown.
INSPECTION
M1429001400282
How to make the power window switch
learn the fully clo
sed position of the
power window
How to make the power window switch
learn the fully closed position when the
power window switch is removed, or the
power window regula tor assembly is
removed or replaced
1. If the anti-trap function (safety mechanism) is activated consecutively three times or more, the
fully closed position that the power window switch
has learned will be er ased (initialised).
2. Operate the power window switch and fully open
the door window glass.