lock MITSUBISHI MONTERO 1991 Repair Manual

Fig. 2: Removing Bearing Case from Axle Shaft
Courtesy of Chrysler Motors.
Inspection
Inspect bearings for roughness, pitting or damage. Inspect
axle shaft for damaged splines or flange. Inspect bearing case for
cracks or damage. Measure axle shaft O.D. in bearing area. Correct O.
D. is 1.57" (39.8 mm). Axle shaft must be replaced if O.D. is not to
specification.
Reassembly
1) Apply grease to outer surface of bearing outer race and
oil seal.Install outer race in bearing case. Install oil seal in
bearing case until it is even with bearing case surface. Apply grease
to bearing rollers. Install brake assembly, bearing case and bearing
onto axle shaft.
2) Apply grease to bearing rollers. Press inner bearing onto
axle shaft. Pack bearing case with grease. Coat lock nut threads with
grease. Install washer, NEW lock washer and lock nut. Lock nut must be
installed with chamfered edge toward axle shaft flange. Tighten lock
nut to specification. See TORQUE SPECIFICATIONS table at end of
article. Bend tab on lock washer into groove on lock nut.
DIFFERENTIAL
NOTE: Check pinion and side gear backlash, ring gear backlash and
ring gear runout before disassembly.
Disassembly
1) Remove differential carrier from axle housing. Remove lock

plates and side bearing nuts. See Fig. 3. Mark bearing caps for
location. Remove bearing caps. Remove differential case assembly from
differential carrier.
CAUTION: Ensure side bearing nuts, bearing caps and side bearings
are marked for location. Components must be installed in
original location.
Fig. 3: Exploded View of Conventional Rear Differential
Courtesy of Chrysler Motors.
2) Using bearing puller, remove differential case side
bearings. Place alignment marks on ring gear and differential case for
reassembly. Loosen ring gear bolts in diagonal sequence. Remove ring
gear.
3) On conventional axles, remove drive pinion shaft lock pin
from differential case. Remove differential pinion shaft and thrust
block (if equipped). Remove pinion gears and washers. Remove side
gears and thrust spacers. Mark components for reassembly reference.
4) On limited slip units, mark differential case and
differential case cover for reassembly reference. Remove differential
case retaining screws. Separate differential case and cover. Remove
components from case. See Fig. 4. Mark components for location.

within specification. See FRICTION PLATE & DISC SPECIFICATIONS table.
FRICTION PLATE & DISC SPECIFICATIONS









\









\









\









\









\







Application In. (mm)
Warpage Limit ......................... .003 (.08)
Wear Limit ............................ .004 (.10)









\









\









\









\









\







DIFFERENTIAL OVERHAUL
CASE ASSEMBLY (CONVENTIONAL)
1) Install thrust spacers, side gears, pinion washers and
pinion gears in differential case. DO NOT install thrust block (if
equipped) at this time.
2) Install pinion shaft without lock pin. Check pinion and
side gear backlash. Install wooden wedge to lock side gears. Using
dial indicator, measure gear backlash. See Fig. 5.
3) Backlash must be within specification. See PINION & SIDE
GEAR BACKLASH SPECIFICATIONS table. Adjust backlash by using different
side gear spacers. Ensure both sides are equally shimmed.
PINION & SIDE GEAR BACKLASH SPECIFICATIONS









\









\









\









\









\









\

Application In. (mm)
4-Cylinder Engine
Standard .................. .0004-.0030 (.010-.076)
Wear Limit ............................. .008 (.20)
V6 Engine
Standard ......................... 0-.0030 (0-.076)
Wear Limit ............................. .008 (.20)









\









\









\









\









\









\

Fig. 5: Checking Pinion & Side Gear Backlash
Courtesy of Chrysler Motors.
4) Install thrust block (if equipped) once correct backlash
is obtained. Install pinion shaft lock pin from back side of ring

1) Install drive pinion in differential carrier. Install
spacer, pinion front shim(s) and front pinion bearing. DO NOT install
oil seal. Install pinion flange, washer and retaining nut. Tighten nut
to specification. See TORQUE SPECIFICATIONS table.
2) Check pinion rotating torque. Rotating torque must be
within specification. Correct specification is 3.5-4.3 INCH lbs. (.40-
.48 N.m) without oil seal. Adjust rotating torque by replacing drive
pinion front shims or spacer.
3) Once correct rotating torque is obtained, install oil
seal. Coat seal lip with grease. Install pinion flange so alignment
marks are correct. Apply light coat of grease to contact area of
pinion flange washer.
4) Install new retaining nut. Recheck pinion rotating torque.
Rotating torque must be within specification.
SIDE BEARING
1) Press side bearings onto differential case. Install outer
races. Install differential case into differential carrier. Align
bearing cap index marks, and snug carrier cap bolts. Ensure outer
races and bearing caps are installed in original location. Tighten
bearing cap bolts finger tight.
2) Install side bearing nuts. Tighten bearing cap bolts. See
TORQUE SPECIFICATIONS table. Rotate bearing nuts in and out until
rotation is smooth. Temporarily tighten side bearing nuts to preload
side bearings. See TORQUE SPECIFICATIONS table. Adjust ring gear
backlash.
RING GEAR BACKLASH
1) Lock drive pinion in place. Using dial indicator, check
ring gear backlash at heel of ring gear tooth. Measure at 4 locations
of ring gear. Gear backlash must be within specification. See RING
GEAR BACKLASH SPECIFICATIONS table.
RING GEAR BACKLASH SPECIFICATIONS









\









\









\









\









\









Application In. (mm)
2.4L ....................... .0043-.0063 (.109-.160)
3.0L ....................... .0051-.0071 (.130-.180)









\









\









\









\









\









2) If backlash is less than specification, loosen side
bearing nut at back of ring gear and tighten side bearing nut on tooth
side of ring gear by same amount. If backlash is beyond specification,
loosen side bearing nut at tooth side of ring gear and tighten side
bearing nut at back of ring gear by same amount.
3) After adjusting backlash, tighten both side bearing nuts
half the distance between center of 2 neighboring holes on side
bearing nut. Recheck backlash. Ensure bearing cap bolts are tightened
to specification. See TORQUE SPECIFICATIONS table.
4) Lock plates are of 2 designs for hole location of side
bearing nuts. Install proper type lock plate. Tighten lock plate bolt
to specification. See TORQUE SPECIFICATIONS table. Check gear tooth
contact using paint impression method. See GEAR TOOTH CONTACT PATTERNS
in this article.
RING GEAR RUNOUT
Using dial indicator, measure runout at back side of ring
gear. Runout must be within .002" (.05 mm). If runout is excessive,
change ring gear-to-differential case mounting position. Recheck

runout.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS








\









\









\









\









\









\









\







Application Ft. Lbs. (N.m)\
Axle Bearing Lock Nut (Montero) .................. 130-159 (176-216\
)
Bearing Cap Bolt ..................................... 40-47 (54-64)\
Bearing Case-To-Axle Housing Bolt .................... 36-43 (49-58)\
Brake Tube Flare Nut ................................. 10-12 (14-16)\
Differential Carrier-To-Axle Housing Nut
2.4L (2WD) ......................................... 18-22 (24-30\
)
3.0L (4WD) ......................................... 29-40 (39-54\
)
Drain Plug ........................................... 43-50 (58-68)\
Filler Plug .......................................... 29-43 (39-58)\
Lock Plate Bolt ...................................... 11-16 (15-22)\
Pinion Flange Nut ................................ 137-181 (186-245)\
Drive Shaft-To-Flange Bolt ........................... 36-43 (49-58)\
Ring Gear Bolt ....................................... 58-65 (79-88)\
Side Bearing Lock Plate Bolts ........................ 11-16 (15-22)\
Wheel Lug Nut
Montero ........................................... 72-87 (98-118)\
Pickup .......................................... 87-101 (118-137)\









\









\









\









\









\









\









\

FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES

INTERMEDIATE SHAFT SUPPORT BEARINGS
INTERMEDIATE SHAFT SUPPORT BEARING INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bearing rollers, balls or
races are worn, pitted,
noisy, or feel rough when
rotated as an assembly . A .. Require replacement of bearing
assembly.
Bracket bent, affecting
performance ............ A .. Require repair or replacement.
Bracket bent, not
affecting performance .. .. ........ No service suggested or
required.
Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performances) .......... .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Cracked ................. .. ........... Require replacement.
Rough (brinelling,
spalling) .............. A ............ Require replacement.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Seized .................. A ............ Require replacement.









\









\









\









\









\









\









\


KEY INTERLOCK SYSTEMS
See
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS) .
LIMITED SLIPS

See DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES .
LINES
See HOSES, LINES AND TUBES .
LINKAGES (EXTERNAL)
LINKAGE (EXTERNAL) INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Components missing ...... C .. Require replacement of missing
components.
Linkage bent, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage bent, not
affecting performance .. 2 ... Suggest repair or replacement
of linkage.
Linkage binding, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage binding, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage broken .......... A ... Require repair or replacement
of linkage.
Linkage loose, affecting
performance ............ A ... Require repair or replacement
of linkage.
Linkage loose, not
affecting performance .. 1 ... Suggest repair or replacement
of linkage.
Linkage missing ......... C ............ Require replacement.
Linkage noisy ........... 2 .. Suggest repair or replacement.
Out of adjustment ....... B .. Require repair or replacement.
Worn to the extent that it
no longer performs its
intended function ...... A .. Require repair or replacement.









\









\









\









\









\









\









\


LOCKING HUB ASSEMBLIES
LOCKING HUB ASSEMBLY INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Inoperative ............. A ........... ( 1) Require repair or
replacement.
Loose ................... A .. Require repair or replacement.
Seized in any position .. A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation.









\









\









\









\









\









\









\


LOCKING HUB CONTROL KNOBS
LOCKING HUB CONTROL KNOB INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure

vent may force fluid past the seal.








\









\









\









\









\









\









\


SEALS (METAL-CLAD)
See SEALS.
SELECTOR INTERLOCK SYSTEMS
See
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS) .
SERVOS
See ACTUATORS (VACUUM) .
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
See:
ACTUATORS (ELECTRICAL)
CABLES
LINKAGES (EXTERNAL)
SWITCHES
SENSORS
SENSOR INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........... ( 2) Require repair or
replacement.
Leaking
(vacuum/fluid/air) ..... A ............ Require replacement.
Out of adjustment ....... B .......... ( 3) Further inspection
required.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting

incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.









\









\









\









\









\









\









\


TORQUE CONVERTERS
TORQUE CONVERTER INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Converter clutch lock-up
operation is faulty .... A ............ Require replacement.
Cover shell damaged,
affecting performance .. A ............ Require replacement.
Does not meet stall speed
specification .......... B ............ Require replacement.
End play exceeds
specifications ......... B ............ Require replacement.
Hub broken .............. A ............ Require replacement.
Hub cracked ............. A ............ Require replacement.
Internal component
failure ................ A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Pilot broken ............ A ............ Require replacement.
Pilot worn, affecting
performance ............ A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Weights missing ......... C ............ Require replacement.









\









\









\









\









\









\









\


TRANSAXLE MOUNTS
See MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION) .
TRANSDUCERS (TRANSMISSION)
See SENSORS.
TRANSMISSION COOLERS
TRANSMISSION COOLER INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Air flow obstruction .... A ................. Require repair.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Connection leaking ...... A .. Require repair or replacement.
Contaminated ............ A .. Require repair or replacement.
Corroded ................ 1 .. Suggest repair or replacement.
Fins damaged, affecting