display MITSUBISHI MONTERO 2000 Service Owner's Guide

GDI -Troubleshooting <A/T>13A-141
OK
Check the harness wire between the
crankanglesensor and the
engine-A/T-ECU, and repair if
necessary.
MUT-
IIData list
22 Crankanglesensor (Refer to
P.13A-198, DATA LIST
REFERENCE TABLE.)OKIntermittent malfunction
(Refer to GROUP 00 - Points to
Note for Intermittent Malfunctions.)
OK
Measure at the crankanglesensor
connector B-52.
DDisconnect the connector and
measure at the harness side.
(1) The resistance between terminal
1 and earth
OK:
2Wor less
(2) The voltage between terminal 2
and earth
(Ignition switch: ON)
OK:
4.8 - 5.2 V
(3) The voltage between terminal 3
and earth
(Ignition switch: ON)
OK:
System voltage(1) NGCheck the harness between the
crankanglesensor and earth, and
repair if necessary.
NG
Repair
NG
Check the following connector:
D-120NG
Repair
NG
Check the following connector:
B-52NG
Repair
(2) NGMeasure at engine-A/T-ECU
connector D-120.
DMeasure the voltage at the
engine-A/T-ECU terminal.
DDisconnect the connector B-52
DIgnition switch: ON
DThe voltage between terminal 45
and earth.
OK:
4.8 - 5.2 VOKCheck the following connector
:
D-120
Check the following connector:
B-25XNG
Repair
OK
Check the harness wire between the
crankanglesensor and the
engine-A/T-ECU.NG
Repair
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
(3) NG
OK
Check the harness wire between the
crankanglesensor and theengine
control relay, and repair if necessary.OK
Use an analyzer to measure the
output waveform at the crankangle
sensor connector B-52.
DUse the test harness
(MD998478) to connect the
connector, and measure at the
pickup harness side.
DEngine: Idling
DThe voltage between terminal 2
and earth
OK:
A normal waveform should
be displayed as described
on P.13A-212 (Inspection
Procedure Using an Ana-
lyzer). Its maximum value
should be 4.8 V or more,
and its minimumvalue
should be 0.6 V or less
with no noise in waveformNGCheck the crankanglesensor vaneNG
Replace
OK
Replace the crankanglesensor
OK
Check the trouble symptoms.
NG
NG
Repair
OK
Check the harness wires between
the crankanglesensor and the
engine-A/T-ECU, crankanglesensor
and the engine controlrelay, and the
crankanglesensor and earth. Then,
repair if necessary.
OK
Check the trouble symptoms.
NG
Replace the engine-A/T-ECU.
Check the following connectors:
B-25X, D-120


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-143
OK
Check the harness wire between the
intermediate connector and the
engine-A/T-ECU, and repair if
necessary.NG
Repair
NG
NG
Repair
NG
Repair
(2) NGMeasure at engine-A/T-ECU
connector D-120.
DMeasure the voltage at the
engine-A/T-ECU terminal.
DDisconnect connector B-110.
DIgnition switch: ON
DThe voltage between terminal 50
and earth
OK:
4.8 - 5.2 VOKCheck the following connector
:
D-120
Check the harness wire between the
intermediate connector and earth,
and repair if necessary.
OK
Check the harness wire between the
intermediate connector and the
engine controlrelay, and repair if
necessary.
(3) NG
OK
Measure at intermediate connector
B-110
DDisconnect the connector and
measure at the harness side.
(1) The voltage between terminal 1
and earth
(Ignition switch: ON)
OK:
System voltage
(2) The voltage between terminal 2
and earth
(Ignition switch: ON)
OK:
4.8 - 5.2 V
(3) The resistance between terminal
3 and earth
OK:
2Wor less(1) NGCheck the following connector:
B-25XNG
Repair
OK
Replace the camshaft position
sensor
Check the trouble symptoms.
OK
NG
Repair
OK
Check the harness wires between the intermediate connector and the engine-A/T-ECU,
the intermediate connector and theengine controlrelay, and the intermediate connector
and earth. Then, repair if necessary.
NG
Replace the engine-A/T-ECU.
OK
Check the harness wire between the
intermediate connector and the
engine-A/T-ECU.NG
Repair
OK
Use an analyzer to measure the
output waveform at intermediate
connector B-110.
DUse test harness (MB991658) to
connect the connector, and
measure at the pick-up harness.
DEngine: Idling
DSelector lever position: P
DThe voltage between terminal 2
and earth
OK:
A normal waveform should
be displayed as described
on P.13A-212 (Inspection
Procedure Using an Ana-
lyzer), its maximum value
should be 4.8 V or more,
and its minimumvalue
should be 0.6 V or less
with no noise in waveform.(1) NGCheck the following connector:
B-23NG
Repair
OK
Check the harness wire between the
camshaft position sensor and the
intermediate connector.NG
Repair
NG
Check the camshaft position sensing
cylinderNG
OK
Check the trouble symptoms.Intermittent malfunction
(Refer to GROUP 00 - Points to Note for Intermittent Malfunctions.)
OK
Check the trouble symptoms.NGReplace the engine-A/T-ECU.
Replace
OK
Check the following connector:
B-110
Check the following connector:
D-120
Check the following connectors:
B-25X, D-120


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-144
Code No.24 Vehicle speed sensor systemProbable cause
Range of Check
DEngine: Two seconds after theengine wasstarted
DIdle switch: OFF
DEngine speed: 2,500 r/min or more
DDuring high engine load
Set Conditions
DThe sensor output voltage does not change for 4 seconds (no pulse signal
input).DMalfunction of the vehicle speed sensor
DOpen or short circuit in the vehicle speed sensor
circuit or loose connector contact
DMalfunction of engine-A/T-ECU
NOCheck the vehicle speed sensor
(Refer to GROUP 54 - Combination Meter.)
YES
Use an analyzer to measure the output waveform of the
vehicle speed sensor at engine-A/T-ECU connector C-09.
DDriving the vehicle
DSelector lever position: P
DThe voltage between terminal 80 and earth
OK:
A normal waveform should be displayed as described
in OSCILLOSCOPE INSPECTION PROCEDURE,
and noise should not be displayed in the waveform.
(Refer to GROUP 23 - Troubleshooting.)NGCheck the following connectors:
C-09, E-13
NG
Repair
OK
Check the harness wire between intermediate connector E-13
and the engine-A/T-ECU, and repair if necessary.
OK
Check the following connector:
C-09NG
Repair
OK
Check the trouble symptoms.
NG
Replace the engine-A/T-ECU.
Does the speedometer operate normally?


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-148
OK
Use an analyzer to measure the
signal waveform at engine-A/T-ECU
connectors D-119 and D-120.
DEngine: Idling
DSelector lever position: P
DVoltage between terminal 1 and
earth
OK:
A normal waveform should
be displayed as described
on P.13A-214 (INSPEC-
TION PROCEDURE US-
ING AN ANALYZER).NGCheck the following connector:
B-61
OK
Check the following connectors:
B-117 <No.1 injector>, B-114 <No.2
injector>, B-118 <No.3 injector>,
B-115 <No.4 injector>, B-103 <No.5
injector>, B-104 <No.6 injector>NG
RepairNG
OK
OK
Check the harness wire between the
injector and the intermediate
connector.NG
Replace the engine-A/T-ECU.
Repair
Repair
From the previouspage
OK
Check the harness wire between
injector and the intermediate
connector.NG
Repair
OK
Replace the injector.
Check the trouble symptoms.NGReplace the injector driver.
Code No.44, 52, 53 Ignition coil (incorporating power
transistor) systemProbable cause
Range of Check
DEngine speed is approx. 50 - 4,000 r/min.
DEngine is not cranking.
Set Conditions
DThe ignition failure sensor does not send a signal about a certain cylinder for
four seconds. However, except that the ignition failure sensor does not send
a signal about all of cylinders.DMalfunction of the ignition coil
DMalfunction of the ignition failure sensor
DMalfunction of sparkplug
DOpen or short circuit in the primary ignition circuit
or loose connector contact
DMalfunction of engine-A/T-ECU


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-150
Code No.54 Immobilizer systemProbable cause
Range of Check
DIgnition switch: ON
Set Conditions
DImproper communication between the engine-A/T-ECU and the
immobilizer-ECUDOpen or short circuit, or loose connector contact
DMalfunction of the immobilizer-ECU
DMalfunction of the engine-A/T-ECU
NOTE
(1) If the registered ignition keys are close each other when starting the engine, radio interference may
cause this code to be displayed.
(2) This code may be displayed when registering the key encrypted code.
NG
Replace the engine-A/T-ECU.
Check the trouble symptoms.
NG
Replace the immobilizer-ECU
OK
Check the trouble symptoms.
OK
Check the harness wire between the
immobilizer-ECU and the
engine-A/T-ECU, and repair if
necessary.NG
Replace
Check the following connectors:
D-122, D-202, E-13NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-169
INSPECTION PROCEDURE FOR TROUBLE SYMPTOMS
Inspection procedure 1
Communication with all systems is not possible.
Probable cause
The cause is probably a defect in the power supply system (including earth) for
the diagnosis line.DMalfunction of the diagnosis connector
DOpen circuit or short-circuited between
engine-A/T-ECU and diagnosis connector circuit
DMalfunction of the MUT-II
Check the earth line, and repair if
necessary.
(2) NG
Replace the MUT-II.
NG
Check the harness wire between the
power supply and diagnosis
connector, and repair if necessary.
OK
Check the trouble symptoms.NG
Repair
(1) NGCheck the following connectors:
D-27, D-210, D-211
OK
NG
RepairOK
Check the harness wire between
diagnosis connector and the
engine-A/T-ECU.
Measure at the diagnosis connecter
D-23.
(1) The voltage between terminal 16
and earth
OK:
Battery voltage
(2) Continuity between 4 and earth
Continuity between 5 and earth
OK:
Continuity
Inspection procedure 2
Communication with engine-A/T-ECU is not possible.
Probable cause
The cause is probably a defect in the engine-A/T-ECU power supply circuit
(including earth).DOpen circuit or short-circuited harness wire in the
engine-A/T-ECU power supply circuit.
DOpen circuit between engine-A/T-ECU and
diagnosis connector
DMalfunction of the engine-A/T-ECU
NG
Check the harness wire between engine-A/T-ECU and
diagnosis connector.OKCheck the engine-A/T-ECU power supply and earth circuit.
(Refer to P. 13A-189, Inspection procedure 24.)
OK
Check the trouble symptoms.
Check the following connectors:
D-06, D-23, D-122, D - 128,
D-222, E-13NG
Repair
NOTE
On vehicles with multi communication system (MMCS) or RV meter, if a malfunctioncannot be resolved
after the procedure above, check the multi center display unit or RV meter and replace if necessary.
(Refer to GROUP 54 - Clock, multi center display and RV meter.)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-182
Inspection procedure 13
Hesitation, sag, stumble, poor acceleration or surge
Probable cause
The cause is probably a malfunction of the ignition system, air/fuel ratio control
system, electronic controlled throttle valve system, compression pressure, etc.DMalfunction of the ignition system
DMalfunction of the air/fuel ratio control system
DMalfunction of the electronic-controlled throttle
valve system
DImproper compression pressure
DAir stuck in the air intake system
NO
NG
Check that the crankanglesensor andtiming beltcover are
properly installed.
OK
Check that air is sucked in the air intake system.
DBroken intake manifold gasket
DDamaged vacuum hose
DDamaged air intake hose
OK
To the nextpage
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
0 - 400 mV and 600 - 1,000 mV alternates when
the engine is idling(wait for 2 minutes after the en-
gine is started).NGMeasure fuel high-pressure between the fuel pump (high
pressure) and injector. (Refer to P.13A-222.)
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
600 - 1,000 mV when theengine is suddenlyracedNGCheck the oxygen sensor system. (Refer to P.13A-131, code
No.11.)
OK
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system (Refer to
P.13A-162, code No.92.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system (Refer
to P.13A-138, code No.21.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-198.)NGCheck the barometric pressure sensor system (Refer to
P.13A-145, code No.25.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-198.)NGCheck the intake air temperature sensor system (Refer to
P.13A-135, code No.13.)
OK
MUT-
IIData list
26 Acceleratorpedal positionswitch
(Refer to P.13A-198.)NGCheck the acceleratorpedal positionswitch system.
(Refer to P.13A-192, Inspection procedure 28.)
Check the ignition timing. (Refer to GROUP11A - Engine
Adjustment)
MUT-
IISelf-Diag Code
Is a diagnosis code displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
OK


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-183
OK
Check the following items in that order.
DCheck the sparkplug
DCheck the EGR control system
DCheck the compression pressure
DCheck the fuel filter or fuelline for clogging
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is
applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine is
cranked.NGReplace the ignition coil.
OK
Measure fuel high-pressure between the fuel pump (high
pressure) and injector. (Refer to P.13A-222.)NGRepair
From the previouspage
Check the trouble symptoms.Replace the injector. NG
OK
MUT-
IIActuator Test
08 Purge control solenoid valve
(Refer to P.13A-203.)NGCheck the purge control solenoid valve system
(Refer to P.13A-197, Inspection procedure 36.)
Inspection procedure 14
The feeling of impact or vibration when accelerating
Probable cause
In cases such as the above, the cause is probably that there is an ignition leak
accompanying the increase in the sparkplug demand voltage during
acceleration.DMalfunction of the ignition system
Replace the ignition coil.
NG
OK
Check the trouble symptoms.
OK
Check the sparkplugNGReplace
NO
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system
(Refer to P.13A-162, code No.92.)
MUT-
IISelf-Diag Code
Is a diagnosis code displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-184
Inspection procedure 15
The feeling of impact or vibration when decelerating
Probable cause
The cause is probably insufficient intake air due to a faulty electronic-controlled
throttle valve system.DMalfunction of the electronic - controlled throttle
valve system
OK
Clean around the throttle valve. (Refer to P.13A-220.)
OK
MUT-
IIData list
26 Acceleratorpedal positionswitch
(Refer to P.13A-198.)NGCheck the acceleratorpedal positionswitch system (Refer to
P.13A-192, Inspection procedure 28.)
NO
MUT-
IIData list
79 Throttle position sensor (1st channel) (Refer to P.13A-198.)NGCheck the throttle valve position feedback system
(Refer to P.13A-162, code No.92.)
MUT-
IISelf-Diag Code
Are diagnosis codes displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
Inspection procedure 16
Knocking
Probable cause
In case as the above, the cause is probably that the heat value of the spark
plug is inappropriate.DMalfunction of the detonation sensor
DImproper heat range of the spark plugs.
MUT-
IISelf-Diag Code
Is a diagnosis code set?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.
NO
Does knocking occur when the vehicle is driven with the
detonation sensor disconnected?
(At this time, use the MUT-IIto check whether the ignition
timing is retarded fromwhen the detonation sensor connector
is connected.)NOCheck the detonation sensor system. (Refer to P.13A-146,
code No.31.)
YES
Check the following items in that order.
DSpark plugs
DCheck if foreign materials (water, kerosine,etc.) got into
fuel.
Inspection procedure 17
Run-on (Dieseling)
Probable cause
Fuel leakage from injectors is suspected.DMalfunction of the injector
Replace the injector.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

GDI -Troubleshooting <A/T>13A-185
Inspection procedure 18
Too high CO and HC concentration when idling
Probable cause
Abnormal air-fuel ratio is suspected.DMalfunction of the air/fuel ratio control system
DDeteriorated catalyst
OK
To the nextpage
NG
Replace the ignition coil.
OK
Check ignition coil spark for each cylinder.
1. Remove the ignition coil.
2. Install a new sparkplug to the removed ignitioncoil.
3. Disconnect the injector intermediate connector.
Caution
Never touch the connector terminal as approx. 100 V is applied to the injector, or you are seriously injured.
4. Earth the sparkplug electrodesecurely.
5. Check that the sparkplug igniteswhen theengine iscranked.NG
NG
Measure fuel high -pressure between the fuelpump (high
pressure) and injector. (Refer to P.13A-223.)
Check the trouble symptoms.
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
Repeat 0 - 400 mV and 600 - 1,000 mV alternately
during idling(wait for at least 2 minutes after the
enginestarted to run at idle).OKReplace the oxygen sensor.
OK
MUT-
IIData list
11 Oxygen sensor (Refer to P.13A-198.)
OK:
600 - 1,000 mV when theengine is suddenlyracedNGCheck the oxygen sensor system. (Refer to P.13A-131, code
No.11.)
OK
MUT-
IIActuator Test
08 Purge control solenoid valve
(Refer to P.13A-203.)NGCheck the purge control solenoid valve system
(Refer to P.13A-197, Inspection procedure 36.)
OK
MUT-
IIData list
68 EGR valve (Refer to P.13A-198.)NGCheck the EGR valve system (Refer to P.13A-196, Inspection
procedure 35.)
OK
MUT-
IIData list
25 Barometric pressure sensor (Refer to P.13A-198.)NGCheck the barometric pressure sensor system (Refer to
P.13A-145, code No.25.)
OK
MUT-
IIData list
13 Intake air temperature sensor (Refer to P.13A-198.)NGCheck the intake air temperature sensor system (Refer to
P.13A-135, code No.13.)
OK
MUT-
IIData list
21 Engine coolant temperature sensor (Refer to P.13A-198.)NGCheck theengine coolant temperaturesensor system (Refer
to P.13A-138, code No.21.)
NO
Check the ignition timing. (Refer to GROUP 11A - Engine
Adjustment.)NGCheck that the crankanglesensor andtiming beltcover are
properly installed.
MUT-
IISelf-Diag Code
Are diagnosis codes displayed?YESRefer to P.13A-130, INSPECTION CHART FOR DIAGNOSIS
CODES.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk