MITSUBISHI SHOGUN 2008 Owner's Manual (in English)

Instruments and controls
3-27
3
Resetting the outside temperature Press the “RESET” function button to reset the graph of the outside temperature.NOTE●
Depending on factors such as the driving conditions, the displayed temperature may vary from the actual outside temperature.
●
It is possible to set the display unit to °C or °F. Refer to “User customization” on page 3-46.
Frozen road warning This shows the temperat
ure outside the vehicle.
When the outside air temperature drops below about 3 °C (37 °F), the alarm sounds and th
e outside air temperature warn-
ing symbol (A) flashes for about 10 seconds.
CAUTION
!●
There is a danger the road might be icy, even when this symbol is not flashing
, so please take care when
driving.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
27 Wednesday, January 9, 2008 4:32 PM

3-28 Instruments and controls
3
Altimeter
E00518600027
The current elevation in units of 50 m (200 ft) is shown in (A). The elevation is graphed every
5 minutes and the data for up to
4 hours are shown in (B). To adjust the elevation It is possible to adjust the cu
rrently indicated elevation using
the following function buttons:
NOTE●
The elevation is determined
from changes in atmospheric
pressure. Depending on weather conditions, the indicated elevation may differ from th
e actual elevation. Variations
in atmospheric pressure can
cause different elevations to
be shown even in the same location. This behavior does not indicate a fault. Use the
indication as a guide only.
“+”- Adjustment of elevation
The elevation increases by 50 m (200 ft) every time youlightly push the “+” button.If you continue pressing the button for about 2 seconds ormore, the elevation indication is fast-forwarded. Then thesetting is changed to the elevation selected.
“-”- Adjustment of elevation
The elevation decreases by 50 m (200 ft) every time youlightly push the “-” button.If you continue pressing the button for about 2 seconds ormore, the elevation indication is fast-forwarded. Then thesetting is changed to the elevation selected.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
28 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-29
3
Resetting th
e elevation
Press the “RESET” function button to reset the elevation plot- ted in graph.NOTE●
Pressing the “RESET” function button will not reset the indication (C).
●
It is possible to set the display unit to m or ft. Refer to “User customization” on page 3-46.
Barometer
E00518700015
This display shows the atmosphe
ric pressure at the present
location in (A). The atmospheri
c pressure values are graphed
every 5 minutes and the data for up to 4 hours are shown in (B).
BK-BK2008E1ENUK.en-uk-Section6.fm Page
29 Wednesday, January 9, 2008 4:32 PM

3-30 Instruments and controls
3
Resetting the atmospheric pressure Press the “RESET” function button to reset the atmospheric pressure plotted in the graph.NOTE●
Pressing the “RESET” function button will not reset the indication (C).
●
It is possible to set the display unit to hPa, mb, kPa or inHg. Refer to “User customization” on page 3-46.
Calendar
E00518800016
The date is shown. The calendar pattern can be changed to your desired setting. Refer to “Changing the calendar setting” on page 3-42.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
30 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-31
3
Clock-only
E00518900017
Only the clock is shown. The time notation can be changed to the setting you desire. (12 hour / 24 hour) Refer to “User customization” on page 3-46.
Blank
E00519000015
The whole display can be turned into blank. In this case, but- tons remain illuminated.NOTE●
If you operate the audio sy
stem, the audio display pops
up.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
31 Wednesday, January 9, 2008 4:32 PM

3-32 Instruments and controls
3
Selecting settings displays
E00519100045
Every time the “ADJ” button is pressed lightly, the display can be changed to the following:
CAUTION
!●
The driver should not opera
te the display while the
vehicle is in motion.
●
When operating the system,
stop the vehicle in a safe
area.
1- Changing the clock settings
→ p. 3-33
2- Adjusting the display brightness
→ p. 3-35
3- Correcting the compass*
→ p. 3-37
4- Changing the calendar setting
→ p. 3-42
5- User customization
→ p. 3-46
6- Adjusting the barometer
→ p. 3-54
BK-BK2008E1ENUK.en-uk-Section6.fm Page
32 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-33
3
Changing the clock settings
E00519200017
1. Press the “ADJ” butto
n to select the clock setting display.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
33 Wednesday, January 9, 2008 4:32 PM

3-34 Instruments and controls
3
2. It is possible to adjust the clock using the function buttons
3. After making the adjustment, press the “INFO” button to
select the information display.
NOTE●
Vehicles equipped with the Mitsubishi Multi Communica- tion System (MMCS) also have a clock indication, but the time shown by the MMCS may differ from that shown by the centre information disp
lay because different sources
of data are used for automatic adjustment.
“H”- Adjust “hour”.
The indication increases by one hour, every time youlightly press the “H” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the hour selected.
“M”- Adjust “minute”.
The indication increases by one minute, every time youlightly press the “M” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded, and then the setting ischanged to the minute selected.
“SET”- To reset the minutes to zero.
The time is adjusted as described below by pressing thefunction button “SET”.●
10:30-11:29 · · · · Change to 11:00
●
11:30-12:29 · · · · Change to 12:00
In this occasion, the display flashes twice before the set-ting is changed.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
34 Wednesday, January 9, 2008 4:32 PM

Instruments and controls
3-35
3
Adjusting the display brightness
E00519300018
The display brightness can be adjusted at 13 levels for both daytime and nighttime. ●
BRIGHTNESS FOR DAYTIME The display brightness is adjusted when the light switch is in the “OFF” position.
●
BRIGHTNESS FOR NIGHTTIME The display brightness is adjusted when the light switch is in the “ ” or “ ” position.
1. Press the “ADJ” button to sh
ow the brightness adjusting
display.
2. Press the “
←” or “
→” function button to select the setting
you wish to adjust (daytime or nighttime). Then press the “SELECT” function button.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
35 Wednesday, January 9, 2008 4:32 PM

3-36 Instruments and controls
3
3. Use the function buttons to adjust the brightness.
NOTE●
If you next wish to adjust the other adjustment setting (daytime or nighttime), press the “ADJ” button or “BACK” function button.
4. After adjustment, press the
“INFO” button to select the
information display.
NOTE●
As the display brightness can
be adjusted in the center
information display only, the brightness inside the meter cannot be changed.
“+”- To make the display brighter
The display becomes brighter by one step, every timeyou lightly press the “+” function button. If you con-tinue pressing the button for about 2 seconds or more,the indication is fast-forwarded.
“-”- To make the display darker
The display becomes darker by one step, every time youlightly press the “-” function button. If you continuepressing the button for about 2 seconds or more, theindication is fast-forwarded.
“SET”- To set the brightness
Press function button “SET” to set the new brightness.The display will flash twice.
BK-BK2008E1ENUK.en-uk-Section6.fm Page
36 Wednesday, January 9, 2008 4:32 PM