relay NISSAN GT-R 1998 User Guide

TROUBLE DIAGNOSES t i
CONSULT (Cont'd) i
FUNCTION TEST MODE
CHECK ITEM (REMEDY)
FUNCTION
TEST
ITEM JUDGEMENT
CONDITION
lgnition switch: ON
(Engine stopped)
Displays the results of on board
diagnostic system.
SELF-DIAG
RESULTS Objective
system
--
ignition switch: ON
(Engine stopped)
Throttle position sensor circuit is
tested when throttle is opened and
closed fully. ("IDLE POSITION" is
the test item name for the vehicles
in which idle is selected by throttle
position sensor.) Harness and connector
Throttle position sensor (Closed
throttle position)
Throttle position sensor (Closed
throttle position) adjustment
Throttle linkage
Venfy operation in DATA
MONITOR mode.
Throttle
valve:
opened OFF
ON
CLOSED THROTTLE
POSl Throttle valve:
closed
lgnition switch: ON
(Engine stopped)
Throttle position sensor circuit is
tested when throttle is opened and
closed fully.
Harness and connector
Throttle position sensor
Throttle position sensor
adjustment
Throttle linkage
Verify operation in DATA
MONITOR mode.
Range
(Throttle
valve fully opened
- Throttle valve
fully closed) More
than 3.0V THROTTLE POSl
SEN CKT
lgnition switch: ON
(Engine stopped)
Neutral position switch circuit is
tested when shift lever is
manipulated.
lgnition switch: ON
(Engine stopped)
Fuel pump circuit is tested by
checking the pulsation in fuel
pressure when fuel tube is
pinched. Out of
N/P
positions OFF
Harness
and connector
Neutral position switch
Linkage adjustment
PARWNEUT POSl SW CKT
In
N/P positions
Harness and connector
Fuel pump
Fuel pump relay
Fuel filter clogging
Fuel level
There
is pressure pulsation on
the fuel feed hose.
FUEL PUMP
CIRCUIT
--
The valve timing control system is
diagnosed by checking for
operating sound of the solenoid
valve.
lgnition switch: ON
(Engine stopped)
Cooling fan circuit is tested when
cooling fan is rotated.
VALVE
TIMING
SN
CKT
Harness and connector
Cooling fan motor
Cooling fan relay
COOLING
FAN
CIRCUIT RB25DE, RB25DET
The cooling fan rotates and
stops every
3 seconds.
lgnition switch: ON -+ START
Start signal circuit is tested when
engine is started by operating the
starter. Battery voltage and water
temperature before cranking, and
average battery voltage, mass air
flow sensor output voltage and
cranking speed during cranking
are displayed.
Harness and connector
lgnition switch
START
SIGNAL
CIRCUIT Start
signal: OFF 3 ON

TROUBLE DIAGNOSES
Symptom Matrix Chart
RELATION BETWEEN CONTROL ITEMS AND SENSORSfACTUATORS
@: High possibility to control damage 0: Low possibility to control damage
Sensors and actuators
1$1$1$ r I I
Crankshaft position sensor 1@1@1@
Ring gear crankshaft position sensor
[RB20DE (UB)] @
Mass air flow sensor
I Engine coolant temperature sensor I 0 I @ I 0 i I
Heated oxygen sensor 0
Knock sensor
Vehicle speed sensor
e? - 01 0
Throttle position sensor 000 C. $ Turbo pressure sensor (TIC) 0 0
Refrigerant pressure sensor
START
lgnition switch
@ 0
IGN 000
Air conditioner switch
Parklneutral position switch
Power steering oil pressure switch
Electrical load switch
Battery
voltage
0
injector @GO I
I power transistor I I I Ignition system I I I lgnition coil I I I I
AAC valve
Fuel DumD relav
. . I I I
2 o ECM & IGN coil relay I@l@l@ 1 I I % Auxiliary electric fan relay 3 - 2 Air conditioner relay
Canister purge control valve
0
Variable valve timing control solenoid valve
Variable air intake control solenoid valve
, (NA) Air jet swirl control solenoid valve
[RB20DE (UB)] 0
Turbo pressure control solenoid valve
(TW
FPCM (TIC)
%' Dropping resistor (TIC) 2. I I 5 Air regulator
Canister 0

*va r TROUBLE DIAGNOSES
Symptom Matrix Chart (Cont'd)
"- RELATION BETWEEN TROUBLE SYMPTOMS AND ACTUATORS - Actuators No
Start Hard
start Rough
idle
Poor derivability Engine
stall
Symptom
. @: High possibility 0: Low possibility
Coil Open
Open
Open
Short
I Injection port Foreign
material
Ignition signal (Power
transistor drive signal)
Ignition primary signal
(Power transistor
ground)
Primary
si'de
.- c. - k Secondary side -
2 Power supply
Fuel pump relay
Auxiliary electric fan
relay
[RB25DE,
RB25DEfl
hen
Canister purge con-
trol valve
Variable valve timing
control solenoid valve
~
Variable air intake
control solenoid valve
Air jet swirl control
solenoid valve
Turbo pressure con-
trol solenoid valve
Injector ground (Total
ground) nstantaneous
reak
I ': Fast idle

TROUBLE DIAGNOSES
Symptom Matrix Chart (Cont'd)
An open circuit causes no fuel injection to the corresponding cylinder, and the heated oxygen sensor output becomes lean. When the open circuits are
observed at all cylinders, the engine will not start.
Actuator-related malfunction
Injector Symptom
characteristics and inspection hints
Drive
circuit
lgnition signal
(POW&
transistor
drive
siqnal)
(open
Injection Open
Short
Fuel pump relay
1 Open 1 Engine will not start. In case of instantaneous break, surging may occur.
A
short circuit causes continuous fuel injection to the corresponding cylinder, and
over-rich airlfuel ratio and misfire will be noted. When the short circuits are
observed at all cylinders, the engine will not start.
Foreign
material
Clogs
L
Foreign
material causes continuous fuel injection to the corresponding cylinder.
Symptoms vary with the condition how the injection port is clogged.
Aidfuel ratio
compensation factor becomes larger.
(1 10 to 125%)
Canister purge control valve Ignition primary
signal (Power
transistor ground)
Auxiliary electric fan relay
[RB25DE, RB25DETI
1 Short
Open
Open -
Open
Open
Leaks
Open
Open
lgnition coil
AAC valve
The valve purges constantly. In summertime, engine may stall at idle speed due
i to rich aidfuel ratio. In wintertime, various malfunctions may occur due to lean
airlfuel ratio.
An open circuit causes no fuel injection to the corresponding cylinder, and the '
heated oxygen sensor output becomes lean. When the open circuits are observed at all cylinders, the engine will not start. In case of instantaneous break, symptoms vary with the break time and the
vehicle's driving conditions. Light shock or surging will occur while the vehicle
is being driven.
The engine will stall when break time is long.
AAC valve is fully closed. Symptoms vary with the base engine speed. When it is
too low, engine may stall while the vehicle is decelerating or when the power
steering load or electrical load is applied.
Power
supply
s~de
primary
Second-
arY side
Power
supply
Drive
circuit
Open Open Auxiliary
electric fan will not operate even after warm-up is completed.
The valve
will not purge. Gasoline smell may be noted when the weather is hot.
Variable valve timing control
solenoid valve
Variable air intake control sole-
noid valve (NA)
Air jet swirl control solenoid
valve
[RB20DE
(UB)]
Injector ground (Total ground) lnstanta- Symptoms vary
with the break time and the vehicle's driving conditions. Surging neous break or engine stall may occur when the instantaneous break occurred during fuel
I I injection. I
Open
, Open
Short
Turbo pressure control solenoid
valve (TIC) Valve
timing not switched.
Variable air intake valve opens, and torque in low speed range is reduced.
Variable air intake valve closes, and torque in high speed range is reduced.
Open
Short Air jet
swirl control valve remains closed.
Air jet swirl control valve remains open.
Open
Open Swing valve opens earlier, and
maximum turbo pressure is reduced.
Engine will not start
because the injectors do not operate.

TROUBLE DIAGNOSES
P ECM (aTCM) InputDutput Signal Reference
Value
SIGNAL VOLTAGES MEASURED WITH OSCILLOSCOPE AND CIRCUIT TESTER
- Signal voltages measured at ECM (-TCM) terminals (terminals for engine control) with a circuit tester and
example of waveforms displayed on an oscilloscope are shown below.
For signal terminals for A/T control, refer to "AIT Trouble Diagnosis" in AT section.
Measured data are affected by many factors such as irregularity of parts, vehicle history, operating
conditions, environment, service status, and measuring instruments and methods.
Terminal
No.
RX / TX
Signal name
I nition signal 8 ower transistor
drive signal)
CH~~"N
ECM & IGN coil
relay control signal (Data
link connector for CONSULT)
Tachometer drive
signal
NOTE: Above
At idle
When cranking: Approx. 0.1 2V
At idle: Approx. 0.1 V
?pprox. 1V
,During approx. 1.5
sec. after ignition switch turned OFF: 4pprox. 1 V 1.5 sec. after ignition switch turned OFF: Battery voltage)
:RB20DE
(UB),
RB25DEJ
Approx.
1.2V
:RB25DET]
Approx.
7.2V At
approx. 2,000 rpm
Approx. 0.15
- 0.25V
Approx. 3V
voltages are measured values obtained by analog circuit tester.
EC-39

TROUBLE DIAGNOSES
ECM (-TCM) InputlOutput Signal Reference
Value (Cont'd)
d
voltages are
Terminal No. Signal name
At idle At
approx. 2,000 rpm
Approx.
12V Approx. 8V
AAC valve control
signal
[RB20DE
(UB), RB25DEl
During 5 sec. after ignition switch tumed ON: Approx. 0.25V 5 sec. after ignition switch turned ON: Battery voltage
When cranking: Approx. 0.25V At idle: Approx. 0.25V Fuel pump relay
control signal - - [RB25DETJ
During 3 sec. after ignition switch tumed ON: Approx.
0.9V
3 sec. after ignition switch tumed ON: Battery voltage
When cranking: Approx. 0.9V At idle: Approx. 0.9V
Approx. 0.9V
Air conditioner
relay control signal Air conditioner
OFF: Battery voltage
Air conditioner ON: Approx. 0.25V
MIL OFF: Battery voltage
MIL ON
RBZODE
(UB), RB25DE: Approx. 0.85V RB25DET Approx. 0.1 V
Malfunction indica-
tor lamp
lgnition switch
(START) signal
Air conditioner
switch signal Approx.
OV (Ignition
switch at START Battery voltage)
Air conditioner OFF: Approx.
4.7V Air conditioner ON: Approx. 0.1 V -
22 (CHK) Check
(Diagnosis
start)
Throttle position
sensor signal
lgnition switch
(IGN) signal CONSULT
connected: Approx. OV CONSULT not connected: Approx. OV
Accelerator pedal released: Approx. OSV Accelerator pedal fully depressed: Approx. 4.2V
(Ignition switch ON, engine not running)
lgnition switch
OFF: Approx. OV lgnition switch ON: Battery voltage Approx.
0.6 - 0.7V
24
(IGN)
Ground Approx.
OV
Power
steering oil
pressure switch
signal Steering
wheel not tumed: Approx. 4.N Steering wheel turned: Approx. OV
26
NOTE: I bove measured values obtained by analog ircuit
tester.

TROUBLE DIAGNOS
ECM (.TCM) lnpu
:s
3utput Signal Reference
Value (Cont'd)
.. No.
Fluctuates between approx. 0.1 to
0.4V and approx.
0.7 to
0.9V At
idle
- I I - I I -
I
I
- are measured
At approx. 2,000 rpm
:v: i .5 I .O 0.5 0
ECL 1 8645 11jllllllll ECL 1 8630
Throttle motor sensor
signal
[RB25DET'J Approx. 3.4V
I (Voltage becomes lower when TCS operates.)
Motor throttle switch
signal
[RB25DET]
Approx.
4.7V
Mass air flow sensor
signal
t
(When TCS is operating: Approx. OV)
Ignition switch ON: Approx.
0.2V
At idle: Approx.
1
.I - 1.2V Approx.
1.6 - 1.7V
Mass air flow sensor
ground Approx.
OV
I
Coolant temperature approx. 20°C: Approx. 3.5V
Coolant temperature approx.
80°C: Approx. 1.2V
Approx. 0.36V min.
(Voltage increases as the air conditioner refrigerant
pressure increases.)
Approx. 0.4
- 2V (') ': Voltage varies with measuring range (internal resis-
tame) of a circuit tester.
Battery voltage
C
+
+
+
56
-
62 1 Knock sensor signal 1
Engine coolant tem-
perature sensor signal
57
- -- -
63 1 Knock sensor signal 2
Refrigerant pressure
sensor
67 Control unit power
sup-
72
I PIY Receive (Data input to
control unit) 1
Transmit (Data output
from control unit) CONSULT
connected: Approx. 0.25V
CONSULT
not connected: Battery voltage
CONSULT connected: Approx.
9V max. CONSULT not connected: Approx. OV
C
Fan stopped: Battery voltage
Fan operating: Approx. 0.2 - 0.3V 78
NOTE: Above
Auxiliary electric fan
relay control signal
[RB25DE, RB25Dm
voltages values obtained
analog circuit
tester.

TROUBLE DIAGNOSES
Component Parts Location
[M-AT (Except TCS)]
Control valve uppe:
Line pressure
solenoid Shift solenoid A
Shift solenoid B Overrun clutch
solenoid
Steering switch relay I Ql Shift control unit (Except RB20DE) ?
ATN 1 985D
AT-?

TROUBLE DIAGNOSES
Circuit Diagram (Cont'd)
Data link connector for C0NS;ILT
Engine speed signal -
i? Throttle ~otal controi port&-2 s-2 33 7'' ELM I E - , 10
AT mode SW & '' 19
(2WD)
1- 1 I I Throttle msition sensor
I I Vehicle speed sensor 1
Turbine sensor 38 -
Throttle position SW 2 r I- 16
L TO IGN SW I PNPSW
To starter relay 4-1 34 - 27
A i 26
n I IGN IOA ID OFF 1ND.L AT> I T 22 I Shift CIU
ATN 1 987D

ANTI-LOCK BRAKE SYSTEM
Fail-safe Function
If any malfunction is detected in the system, the ABS warning lamp
in the instrument panel is turned on with the ABS deactivated and
the vehicle's brake system reverts to normal operation.
System Diagram
ABS control uni: Actuator
Front lefl wheel sensor
Rear wheel Sensor Front
right inlet solenoid valve 1 I -
L ' Data ltnk connector
for CONSULT
Front right outlet solenold valve
Front lett rnlet solenoid vJve
Front left cutlet solenoid valve
r i Rear inlet solenold valve
Contrd
circuit I
Rear outlet solenoid valve
-A Motor (motor relay)
-- Actuator relay
Faii-safe
circuit
TrO~ble
diagnos~s
circuit ABS
warning lamp