NISSAN NOTE 2016 Service Repair Manual

EXT-24
< REMOVAL AND INSTALLATION >
FRONT BUMPER
TYPE 2
Removal and InstallationINFOID:0000000012432166
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
REMOVAL
1. Remove the front grille. Refer to EXT-32, "Removal and Installation".
AWKIA3151ZZ
1. Front bumper fascia side bracket
(RH) 2. Front bumper reinforcement 3. Front energy absorber
4. Front fascia side deflector (RH) 5. Front fog lamp (RH) 6. Front fog lamp finisher (RH)
7. Tow cover 8. Front license plate bracket 9. Front fog lamp finisher (LH)
10. Front bumper fascia 11. Front fog lamp (LH)12. Front fascia side deflector (LH)
13. Front under cover 14. Front bumper fascia side bracket
(LH) 15. Front bumper reinforcement
bracket (RH)
16. Front bumper reinforcement
bracket (LH) A. J nut
Pawl
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT BUMPEREXT-25
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
2. Remove the four front bumper fascia upper clips.
3. Remove the front under cover. Refer to EXT-39, "
FRONT UNDER COVER : Removal and Installation".
4. Partially remove front fender protectors (LH/RH) at the front edge to access front bumper fascia bolts.
Refer to EXT-38, "
Exploded View".
5. Remove front bumper fascia bolts (A) (LH/RH).
6. Remove the front bumper fasci a from the front bumper fascia
side brackets (LH/RH) by releasing the pawls as shown.
: Pawl
CAUTION:
When removing front bumper fascia, two people are
required to avoid damaging.
7. Disconnect the harness connectors from t he front fog lamps (LH/RH) (if equipped).
8. Remove front bumper fascia.
9. Remove the following parts after removing front bumper fascia (if necessary). • Tow cover
• Front fog lamps (LH/RH) (if equipped). Refer to EXL-104, "
Removal and Installation".
• Front license plate bracket
• Front bumper finisher (if equipped)
10. Remove the active grille shutter (if equipped) (if necessary). Refer to EXT-33, "
Removal and Installation"
(ACTIVE GRILLE SHUTTER).
11. Remove the front energy absorber (if necessary).
12. Remove nuts and front bumper reinforcement (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
Tighten the front bumper reinforcement nuts to specification. Refer to EXT-23, "
Exploded View".
NOTE:
• The following table shows the specified values for checking normal installation specifications.
• Fitting adjustment cannot be performed.
JMKIA8017ZZ
AWKIA1890ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-26
< REMOVAL AND INSTALLATION >
FRONT BUMPER
TYPE 1
AWKIA2515ZZ
SectionMeasurement MinimumTarget Value Maximum
A-A Clearance 0.0 (0.00)2.0 (0.08)4.0 (0.16)
B-B Clearance 2.4 (0.09)4.4 (0.17)6.4 (0.25)
B-B Surface height -1.5 (-0.06)0.5 (0.02)1.99 (0.08)
C-C Clearance 0.0 (0.00)2.0 (0.08)4.0 (0.16)
D-D Clearance 0.0 (0.00)1.5 (0.06)3.0 (0.12)
D-D Surface height 0.0 (0.00)1.5 (0.06)3.0 (0.12)
E-E Clearance 0.01 (0.00)2.0 (0.08)4.0 (0.16)
F-F Clearance 0.1 (0.00)0.3 (0.01)1.0 (0.04)
F-F Surface height -0.1 (0.00)0.7 (0.03)1.7 (0.07)
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT BUMPEREXT-27
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
TYPE 2
ALKIA3632ZZ
Section Measurement MinimumTarget Value Maximum
A-A Clearance -1.8 (-0.07)0.7 (0.03)3.2 (0.13)
B-B Clearance 2.4 (0.09)4.4 (0.17)6.4 (0.25)
B-B Surface height -1.5 (-0.06)0.5 (0.02)1.99 (0.08)
C-C Clearance 0.0 (0.00)2.0 (0.08)4.0 (0.16)
D-D Clearance 0.0 (0.00)1.5 (0.06)3.0 (0.12)
D-D Surface height 0.0 (0.00)1.5 (0.06)3.0 (0.12)
E-E Clearance 0.01 (0.00)2.0 (0.08)4.0 (0.16)
F-F Clearance 0.1 (0.00)0.3 (0.01)1.0 (0.04)
F-F Surface height -0.1 (0.00)0.7 (0.03)1.7 (0.07)
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-28
< REMOVAL AND INSTALLATION >
REAR BUMPER
REAR BUMPER
Exploded ViewINFOID:0000000012432167
TYPE 1
AWKIA2520ZZ
1. Rear bumper fascia side bracket (LH) 2. Rear bumper reinforcement support
(LH) 3. Rear bumper closing (LH)
4. Rear bumper fascia 5. Rear bumper finisher 6. Rear bumper fascia spacer
7. Rear bumper reinforcement 8. Rear bumper closing (RH) 9. Rear bumper reinforcement
support (RH)
10. Rear bumper fascia side bracket (RH) A. J nut
Pawl
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR BUMPEREXT-29
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
TYPE 2
Removal and InstallationINFOID:0000000012432168
CAUTION:
Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily
substances.
REMOVAL
1. Remove rear combination lamps (LH/RH). Refer to EXL-109, "Removal and Installation".
AWKIA3152ZZ
1. Rear bumper fascia side
bracket (LH) 2. Rear bumper reinforcement support
(LH) 3. Rear bumper closing (LH)
4. Rear bumper fascia 5. Rear bumper finisher 6. Rear bumper reinforcement
7. Rear bumper closing (RH) 8. Rear bumper reinforcement support (RH)9. Rear bumper fascia side
bracket (RH)
A. J nut Pawl
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-30
< REMOVAL AND INSTALLATION >
REAR BUMPER
2. Remove screws (A) and clip (B) from rear bumper closings (1)(LH/RH).
3. Remove the rear bumper fascia upper bolt (A) (LH/RH) from each side of the rear bumper fascia (1).
4. Remove rear bumper fascia lower clips.
5. Remove the rear bumper fascia from the rear bumper fascia side brackets (LH/RH) by releasing the pawls as shown.
: Pawl
CAUTION:
When removing rear bumper fascia, two people are
required to avoid damaging.
6. Remove the following parts after removing rear bumper fascia (if necessary). • Two clips each and rear bumper closings (LH/RH)
• Two screws and rear bumper finisher
• Rear bumper fascia spacers
• Two bolts each and rear bumper side brackets (LH/RH)
7. Remove rear bumper reinforcement nuts and rear bumper reinforcement (if necessary).
8. Remove rear bumper reinforcement support nuts fr om each and the rear bumper reinforcement supports
(LH/RH) (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation specifications.
• Fitting adjustment cannot be performed.
ALKIA2525ZZ
AWKIA2526ZZ
AWKIA2523ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR BUMPEREXT-31
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
TYPE 1
TYPE 2
ALKIA3207ZZ
Section Measurement MinimumTarget Value Maximum
A-A Clearance 0.1 (0.00)0.3 (0.01)1.0 (0.04)
B-B Clearance 0.0 (0.00)1.5 (0.06)3.5 (0.14)
B-B Surface height -1.5 (-0.06)0.5 (0.02)2.5 (0.10)
C-C Clearance 3.0 (0.12)5.0 (0.20)7.0 (0.28)
C-C Surface height -2.0 (-0.08) -1.5 (-0.06) 0.5 (0.02)
D-D Clearance 5.0 (0.20)7.0 (0.28)9.0 (0.35)
ALKIA3633ZZ
SectionMeasurement MinimumTarget Value Maximum
A-A Clearance 5.0 (0.20)7.0 (0.28)9.0 (0.35)
B-B Clearance 3.0 (0.12)5.0 (0.20)7.0 (0.28)
B-B Surface height -2.0 (-0.08) -1.5 (-0.06) 0.5 (0.02)
C-C Clearance 0.0 (0.00)1.5 (0.06)3.5 (0.14)
C-C Surface height -1.5 (-0.06)0.5 (0.02)2.5 (0.10)
D-D Clearance -1.5 (-0.06)-0.7 (0.03) 0.3 (0.01)
Revision: August 2015 2016 Versa Note

cardiagn.com

EXT-32
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Exploded ViewINFOID:0000000012432169
Removal and InstallationINFOID:0000000012432170
REMOVAL
1. Remove the front grille finisher clips.
2. Release pawls using a suitable tool and remove the front grille finisher.
3. Disconnect the harness connector from the front camera (if equipped).
4. Release the clips using a suitable tool, then pull the front grille away from vehicle to release pawls andremove.
5. Release pawls and remove front emblem from front grille (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Perform camera image calibration (if equipp ed with around view camera). Refer to AV-179, "
CALI-
BRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description".
1. Front grille finisher2. Front grille 3. Front emblem
4. Front camera (if equipped) ClipPawl
AWKIA2554ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

ACTIVE GRILLE SHUTTEREXT-33
< REMOVAL AND INSTALLATION >
C
DE
F
G H
I
J
L
M A
B
EXT
N
O P
ACTIVE GRILLE SHUTTER
Exploded ViewINFOID:0000000012432171
Removal and InstallationINFOID:0000000012432172
REMOVAL
1. Remove the front bumper fascia. Refer to EXT-24, "Removal and Installation".
2. Remove the radiator core support upper. Refer to DLK-144, "
RADIATOR CORE SUPPORT UPPER :
Removal and Installation".
3. Reposition the radiator and condenser as necessa ry to access active grille shutter bolts.
4. Remove the active grille shutter bolts.
5. Release active grille shutter harness clips using a suitable tool.
6. Disconnect the harness connector (A) from the active grille shut- ter (1).
7. Remove the active grille shutter nut (B) (LH/RH).
INSTALLATION
Installation is in the reverse order of removal.
1. Active grille shutter A. Active grille shutter harness connector
ALKIA3641ZZ
ALKIA3150ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com