sensor NISSAN NOTE 2016 Service Repair Manual

DIAGNOSIS SYSTEM (ECM)EC-65
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
CRUISE LAMP ON/OFF
Indicates [ON/OFF] cond
ition of CRUISE lamp de-
termined by the ECM according to the input signals.
SET LAMP* ON/OFFIndicates [ON/OFF] condition of SET lamp deter-
mined by the ECM according to the input signals.
ALT DUTY %Indicates the duty ratio of the power generation
command value. The ratio is calculated by ECM
based on the battery current sensor signal.
BAT CUR SEN mVThe signal voltage of battery current sensor is dis-
played.
A/F ADJ-B1 —Indicates the correction of a factor stored in ECM.
The factor is calculated from the difference between
the target air-fuel ratio stored in ECM and the air-
fuel ratio calculated from A/F sensor 1 signal.
P/N POSI SW ON/OFFIndicates [ON/OFF] condition from the park/neutral
position (PNP) signal.
INT/A TEMP SE °C or ° F The intake air temperature (determined by the sig-
nal voltage of the intake air temperature sensor) is
indicated.
AC PRESS SEN VThe signal voltage from the refrigerant pressure
sensor is displayed.
CLUTCH P/P SW ON/OFF Indicates [ON/OFF] condition clutch pedal position
switch signals. Models other than M/T models always
display OFF.
VTC DTY EX B1 %• The control value of the exhaust valve timing con-
trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.
• The advance angle becomes larger as the value
increases.
THRTL STK CNT
B1* ——
EVAP LEAK DIAG YET/CMPLT • Indicates the condition of EVAP leak diagnosis.
YET: EVAP leak diagnosis has not been per-
formed yet.
CMPLT: EVAP leak diagnosis has been per-
formed successfully.
EVAP DIAG READY ON/OFF • Indicates the ready condition of EVAP leak diag-
nosis.
ON: Diagnosis has been ready condition.
OFF: Diagnosis has not been ready condition.
A/F SEN1
DIAG1(B1) INCMP/CM-
PLT • Indicates DTC P015A or P015B self-diagnosis
condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
A/F SEN1
DIAG2(B1) INCMP/CM-
PLT • Indicates DTC P014C or P014D self-diagnosis
condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
A/F SEN1
DIAG3(B1) ABSNT/
PRSNT • Indicates DTC P014C, P014D, P015A or P015B
self-diagnosis condition.
- ABSNT: The vehicle condition is not within the di- agnosis range.
- PRSNT: The vehicle condition is within the diag-
nosis range.
HO2 S2 DIAG2(B1) INCMP/CM-
PLT • Indicates DTC P0139 self-diagnosis (slow re-
sponse) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
EOP SENSOR mV The signal voltage of EOP sensor is displayed.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-66
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
HO2 S2 DIAG1(B1)INCMP/CM-
PLT • Indicates DTC P0139 self-diagnosis (delayed re-
sponse) condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAG-
NOSIS A B1 INCMP/CM-
PLT • Indicates DTC P219A self-diagnosis condition.
- INCMP: Self-diagnosis is incomplete.
- CMPLT: Self-diagnosis is complete.
SYSTEM 1 DIAG-
NOSIS B B1 ABSNT/
PRSNT • Indicates DTC P219A self-diagnosis condition.
- ABSNT: Self-dia
gnosis standby
- PRSNT: Under self-diagnosis
A/GRLL SHTTR PO-
SITION F/CLOSE
MOVING
F/OPENUNIDTF • Indicates the status of active grille shutter.
- F/CLOSE: Active grille shutter is fully closed.
- MOVING: Active grille shutter is in motion.
- F/OPEN: Active grille shutter is fully opened.
- UNIDTF: Unable to specify the shutter position.
A/GRLL SHTTR
CALIBRATION INCMP/CM-
PLT • Indicates initial position learning status of active
grille shutter.
- CMPLT: The leaning is complete.
- INCOMP: The learning is incomplete.
A/GRLL SHTTR
CIRCUIT DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter circuit.
-OK: Normal.
- NG: Malfunction detected.
A/GRLL SHTTR
TEMP DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter actuator temperature status.
-OK: Normal
- NG: Abnormal temperature detected.
A/GRLL SHTTR
VOLT DIAG OK/NG• Indicates the diagnosis result of active grille shut-
ter voltage status.
-OK: Normal
- NG: Abnormal voltage detected.
A/GRLL SHTTR
OVER RUN OK/NG• Indicates active grille shutter moves beyond nor-
mal moving limit.
-OK: Normal
- NG: Malfunction detected.
A/GRLL SHTTR
STUCK OK/NG• Indicates the diagnosis result of active grille shut-
ter stuck or the operation range less than normal.
-OK: Normal
- NG: Malfunction detected.
A/GRLL SHTTR
CALIB DIAG OK/NG• Indicates the diagnosis result of initial position
learning of active grille shutter.
-OK: Normal
- NG: Deficiency detected.
A/F-S ATMSPHRC
CRCT B1 —Displays a determined value of atmospheric correc-
tion factor necessary for correcting an A/F sensor
signal input to ECM. The signal used for the correc-
tion is an A/F sensor signal transmitted while driving
under atmospheric pressure.
A/F-S ATMSPHRC
CRCT B2 —Displays a determined value of atmospheric correc-
tion factor necessary for correcting an A/F sensor
signal input to ECM. The signal used for the correc-
tion is an A/F sensor signal transmitted while driving
under atmospheric pressure.
A/F-S ATMSPHRC
CRCT UP B1 countDisplays the number of updates of the A/F sensor
atmospheric correction factor.
A/F-S ATMSPHRC
CR CT UP B2 coun
t Dis

plays the number of updates of the A/F sensor
atmospheric correction factor.
Monitored item Unit
DescriptionRemarks
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-68
< SYSTEM DESCRIPTION >[HR16DE]
DIAGNOSIS SYSTEM (ECM)
*: Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.TEST ITEM
CONDITION JUDGMENTCHECK ITEM (REMEDY)
FUEL INJECTION • Engine: Return to the original trouble
condition
• Change the amount of fuel injection
using CONSULT. If trouble symptom disappears, see
CHECK ITEM.
• Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1
ENG COOLANT
TEMP • Engine: Return to the original trouble
condition
• Change the engine coolant tempera-
ture using CONSULT. If trouble symptom disappears, see
CHECK ITEM.• Harness and connectors
• Engine coolant temperature
sensor
• Fuel injector
PURG VOL CONT/V • Engine: After warming up, run engine
at 1,500 rpm.
• Change the EVAP canister purge vol-
ume control solenoid valve opening
percent using CONSULT. Engine speed changes according to
the opening percent.
• Harness and connectors
• Solenoid valve
FUEL/T TEMP SEN Change the fuel tank temperature using CONSULT.
COOLING FAN* • Ignition switch: ON
• Turn the cooling fan “LOW”, “HI” and
“OFF” CONSULT. Cooling fan moves and stops.
• Harness and connectors
• IPDM E/R (Cooling fan relay)
• Cooling fan motor
ALTERNATOR
DUTY • Engine: Idle
• Change duty ratio using CONSULT.
Battery voltage changes.• Harness and connectors
• IPDM E/R
•Alternator
FUEL PUMP RELAY • Ignition switch: ON
• Turn the fuel pump relay “ON” and
“OFF” using CONSULT and listen to
operating sound. Fuel pump relay makes the operat-
ing sound.
• Harness and connectors
•Fuel pump relay
IGNITION TIMING • Engine: Return to the original trouble
condition
• Timing light: Set
• Retard the ignition timing using CON- SULT. If trouble symptom disappears, see
CHECK ITEM.
Perform Idle Air Volume Learn-
ing.
POWER BALANCE • Engine: After warming up, idle the en-
gine.
• A/C switch OFF
• Shift lever: P or N (CVT), Neutral (M/
T)
• Cut off each fuel injector signal one at
a time using CONSULT. Engine runs rough or dies.
• Harness and connectors
• Compression
• Fuel injector
• Power transistor
• Spark plug
• Ignition coil
VENT CONTROL/V • Ignition switch: ON
• Turn solenoid valve ON and OFF with
the CONSULT and listen to operating
sound. Solenoid valve makes an operating
sound.
• Harness and connectors
• EVAP canister vent control
solenoid valve
INT V/T ASSIGN
ANGLE • Engine: Return to the original non-
standard condition
• Change intake valve timing using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Harness and connectors
• Intake valve timing control
solenoid valve
EX H V/T ASSIGN
ANGLE •
E

ngine: Return to the original non-
standard condition
• Change exhaust valve timing using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM.
• Harness and connectors
• Exhaust valve timing control
solenoid valve
ACTIVE GRILLE
SHUTTER NOTE:
Initial position learning is required every
time when the ignition switch is turned
OFF.
1. Engine: Idle speed
2. Touch “CALIBRTN” to perform ini-
tial position learning.
3. Touch “OPEN” or “CLOSE” to op- erate active grille shutter. Active grille shutter fully opens or
fully closes.
• Harness or connector
• Active grille shutter actuator
• Active grille shutter
Revision: August 2015
2016 Versa Note

cardiagn.com

DIAGNOSIS SYSTEM (ECM)EC-69
< SYSTEM DESCRIPTION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
DTC WORK SUPPORT MODE
Test Item
SRT & P-DTC MODE
SRT STATUS Mode
• For items whose SRT codes are set, “CMPLT” is di
splayed on the CONSULT screen; for items whose SRT
codes are not set, “INCMP” is displayed.
• “SRT STATUS” provides the presence or absenc e of permanent DTCs stored in ECM memory.
PERMANENT DTC STATUS Mode
How to display permanent DTC status1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
4. Turn ignition switch ON.
5. Select “PERMANENT DTC STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT.
NOTE:
Permanent DTCs stored in ECM memory are displayed on the CONSULT screen to show if a driving pat-
tern required for erasing permanent DTCs is complete (CMPLT) or incomplete (INCMP).
CAUTION:
Since the “PERMANENT DTC STATUS ” screen displays the previous trip information, repeat the
following twice to update the in formation: “Ignition switch OFF”, “Wait for more than 10 seconds”
and “Ignition switch ON”.
NOTE:
This mode is not used in regions that permanent DTCs are not regulated by law.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
PERMANENT DTC WORK SUPPORT Mode
Test modeTest itemCorresponding DTC No. Reference page
A/F SEN1 A/F SEN1 (B1) P1276
P0130EC-213, "
DTC Logic"
A/F SENSOR1 (B1) P014C/P014D P014C/P014DEC-243, "DTC Logic"
A/F SENSOR1 (B1) P015A/P015BP015A/P015B EC-243, "DTC Logic"
EVAPORATIVE SYSTEM PURG FLOW P0441 P0441
EC-290, "DTC Logic"
PURG VOL CN/V P1444P0443EC-295, "DTC Logic"
HO2S2 HO2S2 (B1) P1146
P0138EC-229, "
DTC Logic"
HO2S2 (B1) P1147 P0137EC-223, "DTC Logic"
HO2S2 (B1) P0139 P0139EC-237, "DTC Logic"
JSBIA0062GB
Revision: August 2015 2016 Versa Note

cardiagn.com

ECM
EC-71
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000012431342
VALUES ON THE DIAGNOSIS TOOL
NOTE:
• The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
ble to this vehicle, refer to CONSULT display items.
• Numerical values in the following table are reference values.
• These values are input/output values that ECM receiv es/transmits and may differ from actual operations.
Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the
data monitor.
This occurs because the timing light shows a value calculated by ECM according to signals received from
the camshaft position sensor and other sensors related to ignition timing.
• For outlines of following items, refer to EC-60, "
CONSULT Function".
Monitor Item Condition Values/Status
IDLE REQUEST NOTE:
The item is indicated, but not used.
MIL ON REQUEST NOTE:
The item is indicated, but not used.
ENGINE NO-LOAD NOTE:
The item is indicated, but not used.
READY STATE NOTE:
The item is indicated, but not used.
ENG SPEED • Run engine and compare CONSULT value with the tachometer indication.Almost the same speed as
the tachometer indication.
MAS A/F SE-B1 See EC-151, "
Description".
B/FUEL SCHDL See EC-151, "
Description".
A/F ALPHA-B1 See EC-151, "
Description".
COOLAN TEMP/S • Engine: After warming up More than 70°C (158F)
A/F SEN1 (B1) • Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
HO2S2 (B1) • Revving engine from idle up to 3,000 rpm quickly after the following conditions
are met.
- Engine: After warming up
- After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 MNTR (B1) LEAN ←→ RICH
VHCL SPEED SE • Turn drive wheels and compare CONSULT value with the speedometer indi-
cation. Almost the same speed as
speedometer indication
BATTERY VOLT • Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1 • Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released
0.6 - 0.9 V
Accelerator pedal: Fully depressed 4.0 - 4.8 V
ACCEL SEN 2 • Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released
0.6 - 0.9 V
Accelerator pedal: Fully depressed 3.9 - 4.8 V
TP SEN 1-B1 • Ignition switch: ON
(Engine stopped)
• Shift lever: 1st Accelerator pedal: Fully re
leasedMore than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1 • Ignition switch: ON
(Engine stopped)
• Shift lever:1st Accelerator pedal: Fully re
leasedMore than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE • Ignition switch: ON Indicates fuel tank tempera-
ture
Revision: August 2015
2016 Versa Note

cardiagn.com

ECM
EC-75
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
A/F SEN1
DIAG3(B1)
• The vehicle condition is not within the diagnosis range of DTC P014C, P014D,
P015A or P015B. ABSNT
• The vehicle condition is within the diagnosis range of DTC P014C, P014D, P015A or P015B. PRSNT
HO2 S2 DIAG2(B1) • DTC P0139 self-diagnosis (slow response) is incomplete.
INCMP
• DTC P0139 self-diagnosis (slow response) is complete. CMPLT
SYSTEM 1 DIAG-
NOSIS A B1 DTC P219A self-diagnosis is incomplete.
INCMP
DTC P219A self-diagnosis is complete. CMPLT
SYSTEM 1 DIAG-
NOSIS B B1 DTC P219A self-diagnosis
is on standby. ABSENT
DTC P219A self-diagnosis is under diagnosis. PRSENT
EOP SENSOR • Engine: After warming up
• Selector lever position: P or N
(CVT) or Neutral (M/T)
• Air conditioner switch: OFF
•No load Idle
Approx 1,000 - 2,000 mV
2,000 rpm Approx 1,500 - 3,500 mV
HO2 S2 DIAG1(B1) • DTC P0139 self-diagnosis (delayed response) is incomplete.
INCMP
• DTC P0139 self-diagnosis (delayed response) is complete. CMPLT
A/GRLL SHTTR PO-
SITION • Engine RPM: idle speed.
• Vehicle speed: 0 km/h (0 MPH).
F/OPEN
• Vehicle speed: 30 km/h (19 MPH) or faster. (Comply the condition of active grille shutter operation). F/OPEN
→MOVING →F/
CLOSE
A/GRLL SHTTR
CALIBRATION • Turn ignition switch OFF→ ON
• Drive the vehicle at a speed more than 6 km/h (4 MPH) for the first time.
CMPLT
• Turn ignition switch OFF → ON.
• When the vehicle speed does not reach 6 km/h (4 MPH). INCMP
A/GRLL SHTTR
CIRCUIT DIAG • Malfunction of active grill shutter power supply is detected.
NG
• Malfunction of active grill shutter power supply is not detected. OK
A/GRLL SHTTR
TEMP DIAG • Abnormal temperature of active grill shutter actuator is detected.
NG
• Abnormal temperature of active grill shutter actuator is not detected. OK
A/GRLL SHTTR
VOLT DIAG • Abnormal voltage of active grill shutter circuit is detected.
NG
• Abnormal voltage of active grill shutter circuit is not detected. OK
A/GRLL SHTTR
OVERRUN • Active grill shutter does not stop within normal moving limit.
NG
• Active grill shutter stops within normal moving limit OK
A/GRLL SHTTR
STUCK • Detecting the active grille shutter stuck or the operation range less than nor-
mal. NG
• Not detecting the active grille shutter stuck or the operation range less than normal. OK
A/GRLL SHTTR
CALIB DIAG • Malfunction of active grill shutter initial position learning is detected.
NG
• Malfunction of active grill shutter initial position learning is not detected. OK
A/F-S ATMSPHRC
CRCT B1 Engine: After warming up, idle the engine
Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT B2 Engine: After warming up, idle the engine Varies depending on vehicle
environment.
A/F-S ATMSPHRC
CRCT UP B1 Engine: Running Varies depending on the
number of updates.
A/F-S ATMSPHRC
CRCT UP B2 Engine: Running
Varies depending on the
nu
mber of up
dat

es.
A/F IMBALNC DIAG-
CPS STAT The vehicle condition is not within the diagnosis range of DTC P219C – P219F.
ABSNT
The vehicle condition is within the diagnosis range of DTC P219C – P219F. PRSNT
Monitor Item
Condition Values/Status
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-76
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
*: Accelerator pedal position sensor 2 signal and throttle
position sensor 2 signal are converted by ECM inter-
nally. Thus, they differ from ECM terminals voltage signal.
TERMINAL LAYOUT
PHYSICAL VALUES
NOTE:
• Connect a break-out box and harness adapter between the ECM and ECM harness connector.
- Use extreme care not to touch 2 pins at one time.
- Data is for comparison and may not be exact.
• Specification data are reference values and are measured between each terminals.
• Pulse signal is measured by CONSULT.
A/F IMBLNC DIAG-
CPS CMPLT Self-diagnosis of DTC P219C – P219F is incomplete.
INCMP
Self-diagnosis of DTC P219C – P219F is complete. CMPLT
Monitor Item
Condition Values/Status
PBIA9221J
Terminal No.Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
1
(L) 108
(B) Throttle control motor
(Open)
Output[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully de-
pressed 2.6 V
2
(L/W) 108
(B) Throttle control motor power
supply
Input [Ignition switch: ON] BATTERY VOLTAGE
(11 - 14 V)
3
(G/W) 108
(B) A/F sensor 1 heater Output [Engine is running]
• Warm-up condition
• Idle speed
(More than 140 seconds after
starting engine) 2.9 - 8.8 V
4
(P) 108
(B) Throttle control motor
(Close)
Output[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released 1.8 V
JMBIA0213GB
JSBIA0714GB
JMBIA0215GB
Revision: August 2015
2016 Versa Note

cardiagn.com

ECM
EC-77
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
5
(BR/W) 59
(L/Y) Heated oxygen sensor 2
heater
Output[Engine is running]
• Engine speed: Below 3,600 rpm
after the following conditions are
met
- Engine: after warming up
- Keeping the engine speed be- tween 3,500 and 4,000 rpm for 1
minute and at idle for 1 minute
under no load 10 V
[Ignition switch: ON]
• Engine stopped
[Engine is running]
• Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
9
(SB) 108
(B) EVAP canister purge vol-
ume control solenoid valve
Output[Engine is running]
• Idle speed
BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Engine speed: About 2,000 rpm (More than 100 seconds after
starting engine.) BATTERY VOLTAGE
(11 - 14 V)
10
(B) — ECM ground — — —
11
(B/Y) — ECM ground
—— —
12
(L/W)
108(B) Fuel injector No. 1 (Rear)
Output[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle BATTERY VOLTAGE
(11 - 14 V)
16
(G) Fuel injector No. 3 (Rear)
20
(O/W) Fuel injector No. 2 (Rear)
24
(R) Fuel injector No. 4 (Rear)
25
(R) Fuel injector No. 4 (Front)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpmBATTERY VOLTAGE
(11 - 14 V)
29
(G) Fuel injector No. 3 (Front)
30
(O) Fuel injector No. 2 (Front)
31
(L) Fuel injector No. 1 (Front)
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA0214GB
JMBIA0039GB
JMBIA0216GB
JMBIA0221GB
JMBIA0222GB
Revision: August 2015 2016 Versa Note

cardiagn.com

EC-78
< ECU DIAGNOSIS INFORMATION >[HR16DE]
ECM
15
(G/W) 108
(B) Throttle control motor relay Output [Ignition switch: OFF]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: ON] 0 - 1.0 V
17
(V)
108(B) Ignition signal No. 1
Output[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 0 - 0.3 V
18
(Y/B) Ignition signal No. 2
21
(W) Ignition signal No. 4
[Engine is running]
• Warm-up condition
• Engine speed: 2,500 rpm0.2 - 0.5 V
22
(BR) Ignition signal No. 3
23
(GR) 108
(B) Fuel pump relay
Output[Ignition switch: ON]
• For 1 second after turning ignition
switch ON
[Engine is running] 0 - 1.0 V
[Ignition switch: ON]
• More than 1 second after turning ignition switch ON BATTERY VOLTAGE
(11 - 14 V)
26
(P) 108
(B) EVAP canister vent control
valve
Output [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
32
(P) 108
(B) ECM relay
(Self shut-off)
Output[Engine is running]
[Ignition switch: OFF]
• A few seconds after turning igni-
tion switch OFF 0 - 1.0 V
[Ignition switch: OFF]
• More than a few seconds after turning ignition switch OFF BATTERY VOLTAGE
(11 - 14 V)
33
(W) 36
(R) Throttle position sensor 1 Input [Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released
More than 0.36 V
[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully de- pressed Less than 4.75 V
34
(B) 36
(R) Throttle position sensor 2 Input [Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Accelerator pedal: Fully released
Less than 4.75 V
[Ignition switch: ON]
• Engine stopped
• Shift lever: D (CVT), 1st (M/T)
• Acce
l

erator pedal: Fully de-
pressed More than 0.36 V
36
(R) —Sensor ground
(Throttle position sensor) ——
—
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JMBIA0219GB
JMBIA0220GB
Revision: August 2015 2016 Versa Note

cardiagn.com

ECM
EC-79
< ECU DIAGNOSIS INFORMATION > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O37
(W) 40
(L) Knock sensor
Input[Engine is running]
• Idle speed
2.5 V
38
(LG/B) 44
(P) Engine coolant temperature
sensor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
39
(L) 68
(R) Battery temperature sensor Input [Engine is running]
• Battery temperature: 25
°C ( °F)
• Idle speed 3.5 V
40
(L) —Sensor ground
(Knock sensor shield circuit) ——
—
42
(L) 51
(P) Fuel tank temperature sen-
sor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel
tank temperature.
43
(SB) 68
(R) EVAP control system pres-
sure sensor
Input [Ignition switch: ON]
0.5 - 4.6 V
44
(P) —Sensor ground
(Engine coolant tempera-
ture sensor) ——
—
45
(G/B) 52
(LG) Mass air flow sensor
Input[Ignition switch ON]
• Engine stopped
0.4 V
[Engine is running]
• Warm-up condition
• Idle speed 0.8 - 1.3 V
[Engine is running]
• Warm-up condition
• Engine is revving from idle to about 4,000 rpm 0.8 - 1.3 to 2.4 V
(Check for linear voltage rise in
response to engine being in-
creased to about 4,000 rpm.)
46
(V) 55
(G/L) Intake air temperature sen-
sor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with intake
air temperature.
47
(Y) 60
(L) Engine oil pressure sensor Input [Engine is running]
• Warm-up condition
• Idle speed
1.0 - 2.0 V
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 1.5 - 3.5 V
48
(W/R) 63
(W) Ex
haus
t v
alve timing control
position sensor Input[Engine is running]
• Warm-up condition
• Idle speed
NOTE:
The pulse cycle changes de-
pending on rpm at idle 4.3 V
[Engine is running]
• Engine speed: 2,000 rpm 4.3 V
49
(G) 108
(B) A/F sensor 1
Input [Ignition switch: ON] 2.2 V
Terminal No.
Description
ConditionVa l u e
(Approx.)
+ – Signal nameInput/
Output
JSBIA0716GB
JSBIA0717GB
Revision: August 2015 2016 Versa Note

cardiagn.com