height NISSAN NOTE 2016 Service Repair Manual

ACC-4
< REMOVAL AND INSTALLATION >
ACCELERATOR CONTROL SYSTEM
• Check that the accelerator pedal moves smoothly within the speci-fied range.
• Check the accelerator pedal height.
CAUTION:
• Whenever the harness connector of the accelerator pedal position sensor has been disconnected,
perform “ACCELERATOR PEDAL RELEASED POSITION LEARNING”. Refer to EC-128, "
Work Proce-
dure".
• The accelerator pedal should return sm oothly to the fully released position.
Accelerator pedal stroke (A) : Refer to
ACC-5, "
Accel-
erator Control".
ALBIA1151ZZ
Accelerator pedal height : Refer to ACC-5, "Acceler-
ator Control".
Revision: August 2015 2016 Versa Note

cardiagn.com

SERVICE DATA AND SPECIFICATIONS (SDS)ACC-5
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
DE
F
G H
I
J
K L
M A
ACC
NP
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Accelerator ControlINFOID:0000000012432479
Unit: mm (in)
Accelerator pedal stroke (A)
49.8 - 52.6 (1.96 - 2.07)
Accelerator pedal height 113.0 - 123.0 (4.45 - 4.84)
ALBIA1151ZZ
Revision: August 20152016 Versa Note

cardiagn.com

C1142 PRESS SENSORBRC-97
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
Check the brake fluid leakage. Refer to BR-12, "Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace brake fluid leakage part.
3.CHECK BRAKE PIPING
Check the brake piping. Refer to BR-12, "
Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace brake piping. • Front: Refer to BR-23, "
FRONT : Removal and Installation".
• Rear: Refer to BR-26, "
REAR : Removal and Installation".
4.CHECK BRAKE PEDAL
Check the brake pedal.
• Brake pedal height: Refer to BR-9, "
Inspection and Adjustment".
• Brake pedal assembly: Refer to BR-20, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Adjust the brake pedal height or replace brake pedal assembly. • Adjust the brake pedal: Refer to BR-9, "
Inspection and Adjustment".
• Replace the brake pedal: Refer to BR-20, "
Removal and Installation".
5.CHECK BRAKE MASTER CYLINDER
Check the brake master cylinder. Refer to BR-14, "
Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace brake master cylinder. Refer to BR-28, "
Removal and Installation".
6.CHECK BRAKE BOOSTER
Check the brake booster. Refer to BR-15, "
Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace brake booster. Refer to BR-31, "
Removal and installation".
7.CHECK VACUUM PIPING
Check the vacuum piping. Refer to BR-33, "
Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace vacuum piping. Refer to BR-33, "
Removal and Installation".
8.CHECK FRONT DISC BRAKE
Check the front disc brake caliper. Refer to BR-36, "
BRAKE CALIPER ASSEMBLY : Exploded View".
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace front disc brake caliper. Refer to BR-37, "
BRAKE CALIPER ASSEMBLY :
Removal and Installation".
9.CHECK REAR BRAKE
Check the rear brake. Refer to BR-41, "
Exploded View".
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair or replace rear brake. Refer to BR-41, "
Removal and Installation".
10.CHECK ABS ACTUATOR AND ELECTRIC UNIT (C ONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Revision: August 2015 2016 Versa Note

cardiagn.com

CLUTCH PEDALCL-5
< PERIODIC MAINTENANCE >
CEF
G H
I
J
K L
M A
B
CL
N
O P
PERIODIC MAINTENANCE
CLUTCH PEDAL
Inspection and AdjustmentINFOID:0000000012432215
INSPECTION
The Height of Clutch Pedal
1. Turn the floor carpet.
2. Check that the clutch pedal height (H
1) from the dash lower
panel (1) is within the reference value.
3. Replace clutch pedal if the height is outside the reference value.
Clutch Pedal Height When Disengaging The Clutch
1. Securely engage the parking brake.
2. Turn the floor carpet.
3. Start the engine and run at idle.
4. Fully depress clutch pedal and shift to the 1st gear. CAUTION:
Securely depress the brake pedal with shifter lever in 1st gear.
5. Gradually release the clutch pedal and check that the clutch pedal height (H
2) from the dash lower panel (1) is within the ref-
erence value with a scale immediately before the clutch is
engaged.
NOTE:
Although the clutch pedal height differs according to whether the
clutch gets disengaged or engaged, clutch-engaged case is
regarded as clutch-disengaged case for easier inspection.
6. Replace clutch pedal if the height is outside the reference value.
Clutch Pedal Play
1. Push the pedal pad by hand until a resistance can be felt and check that the play (A) on the upper surface of the pedal pad is
within the reference value.
2. Replace clutch pedal if the play is outside the reference value.
Position of Clutch Interlock Switch
Clutch pedal height
(H
1) : Refer to
CL-22, "
Clutch Pedal".
JPFIA0065ZZ
Clutch pedal height at clutch
disengagement (H
2) : Refer to CL-22, "
Clutch
Pedal".
JPFIA0068ZZ
Clutch pedal play (A) : Refer to
CL-22, "Clutch Pedal".
JPFIA0121ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CLUTCH DISC AND CLUTCH COVERCL-21
< UNIT REMOVAL AND INSTALLATION >
CEF
G H
I
J
K L
M A
B
CL
N
O P
Check diaphragm spring levers for unevenness with the clutch cover
installed on the engine. If they exceed the tolerance, adjust dia-
phragm spring lever height, using Tool (A). Tool number (A) : ST20050240 ( — )
Tolerance for diaphragm spring
lever unevenness : Refer to
CL-22,
"Clutch Cover".
JPDIB0160ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

CL-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationsINFOID:0000000012432236
Unit: mm (in)
Clutch PedalINFOID:0000000012432237
Unit: mm (in)
Clutch DiscINFOID:0000000012432238
Unit: mm (in)
Clutch CoverINFOID:0000000012432239
Unit: mm (in)
Type of clutch controlHydraulic
Clutch disc Facing size (Outer dia. × Inner dia. × Thickness) 200 × 140 × 3.1 (7.87 × 5.51 × 0.122)
Recommended clutch fluid Refer to MA-11, "
Fluids and Lubricants".
Clutch pedal height 158.8 – 168.8 (6.25 – 6.65)
Clutch pedal height at clutch disengagement 73 (2.87) or more
Clutch pedal play
[Looseness at clutch pedal pin] 2 – 8 (0.08 – 0.31)
[0 – 1.3 (0 – 0.051)]
Clearance between clutch pedal and clutch interlock switch
threaded end while clutch pedal is fully depressed 0.2 – 1.96 (0.0079 – 0.0772)
Clearance between clutch pedal and clutch pedal position switch
threaded end while clutch pedal is fully released (if equipped) 0.2 – 1.96 (0.0079 – 0.0772)
Clutch facing runout limit / diameter of the area to be measured
1.0 (0.039) / 190 (7.48) dia.
Maximum allowable spline backlash (at outer edge of disc) 0.8 (0.031)
Clutch facing wear limit (depth to the rivet head) 0.3 (0.012)
Tolerance for diaphragm spring lever unevenness0.7 (0.028) or less
Revision: August 2015 2016 Versa Note

cardiagn.com

HOOD
DLK-141
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Installation is in the reverse order of removal.
CAUTION:
• Before installing hood assembl y, apply anticorrosive agent to the surface of hood hinge.
• After installation, perform the hood assembly adjustment procedure. Refer to DLK-141, "
HOOD
ASSEMBLY : Adjustment".
• After installation, ap ply touch-up paint (body color) to the head of hood hinge nuts.
HOOD ASSEMBLY : AdjustmentINFOID:0000000012430087
Check the clearance and the surface height between hood and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Hood assembly 2. Bumper rubber (body side) 3. Hood hinge (LH)
4. Hood lock 5. Front grille finisher6. Front combination lamp
7. Front fender
AWKIA2565ZZ
Section Item Measurement StandardParallelism Equality
A – A D
Clearance 4.4 ± 2.0 (0.17 ± 0.08) 2.0 (0.08) —
E Surface height -0.5 +2.0, -1.5 (0.02 +0.08, -0.06) 2.0 (0.08) —
B – B F
Clearance 4.0 ± 2.0 (0.16 ± 0.08) 2.0 (0.08) 3.0 (0.12)
G Surface height ———
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-142
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
HOOD
CLEARANCE ADJUSTMENT
1. Loosen hood hinge nuts and bolts.
2. Loosen hood lock assembly bolts.
3. Adjust the hood lock assembly so the clearance m
easurements are within the specifications provided.
4. Tighten hood hinge nuts and bolts to specified torque.
5. Tighten hood lock assembly bolts to specified torque.
HEIGHT ADJUSTMENT
1. Loosen hood lock assembly bolts.
2. Adjust the surface height of hood assembly to front upper grille, front fender and front combination lamp to
the specified values by rotating hood bumper rubber.
3. Temporarily tighten hood lock assembly bolts.
4. Adjust (A) as shown to the following value with hood’s own weight by dropping it from approximately 200 mm (7.87 in) height or by pressing hood lightly [approximately 29 N (3.0 kg, 6.5 lb)].
5. After adjustment, tighten hood lock assembly bolts to specified torque.
HOOD HINGE
HOOD HINGE : Removal and InstallationINFOID:0000000012430088
REMOVAL
1. Remove hood assembly. Refer to DLK-140, "HOOD ASSEMBLY : Removal and Installation".
2. Remove front fender. Refer to DLK-147, "
Removal and Installation".
3. Remove cowl top side cover. Refer to EXT-36, "
Exploded View".
4. Remove hood hinge bolts and hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.
C – CH Clearance 3.5
± 1.0 (0.14 ± 0.04) 1.5 (0.06) 1.5 (0.06)
J Surface height 0.0 ± 1.5 (0.0 ± 0.06) 1.5 (0.06) 1.5 (0.06)
Section Item Measurement
StandardParallelism Equality
1. Hood striker 2. Secondary latch3. Primary latch
A. 20.0 mm (0.79 in)
ALKIA3162ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FRONT DOORDLK-151
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Check the clearance and surface height between front door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Remove front fender. Refer to DLK-147, "Removal and Installation".
2. Loosen front door hinge nuts (door side).
3. Adjust the surface height of front door according to the specifications provided.
4. Temporarily tighten front door hinge nuts (door side).
5. Loosen front door hinge bolts (body side).
6. Raise or lower the front door at rear end to adjust clearance of the front door according to the specifica-
tions provided.
7. After adjustment tighten bolts and nuts to the specified torque. CAUTION:
Check door hinge rotating po int for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
8. Install front fender. Refer to refer to DLK-147, "
Removal and Installation".
DOOR STRIKER
DOOR STRIKER : Removal and InstallationINFOID:0000000012430098
REMOVAL
Remove bolts and door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door striker bolts.
• Tighten bolts to specification. Refer to DLK-149, "
Exploded View".
• After installation, check front door open/close operation. If necessary, perform the door striker
adjustment procedure. Refer to DLK-151, "
DOOR STRIKER : Adjustment".
DOOR STRIKER : AdjustmentINFOID:0000000012430099
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
4. Body side outer 5. Door striker 6. Striker bolt
7. Front door hinge 8. Rear door upper hinge9. Rear door lower hinge
Section Measurement Standard
A – A Clearance
4.6 ± 1.0 (0.18 ± 0.04)
Surface height 0.0 ± 1.0 (0.0 ± 0.04)
B – B Clearance
4.6 ± 2.0 (0.18 ± 0.08)
Surface height 0.0 ± 1.5 (0.0 ± 0.06)
C – C Clearance
4.6 ± 1.0 (0.18 ± 0.04)
Surface height 0.0 ± 1.0 (0.0 ± 0.04)
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-156
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000012430104
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specific ation, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Remove center pillar lower finisher. Refer to INT-25, "CENTER PILLAR LOWER FINISHER : Removal
and Installation".
1. Front fender2. Front door 3. Rear door
4. Body side outer 5. Door striker 6. Striker bolt
7. Front door hinge 8. Rear door upper hinge 9. Rear door lower hinge
AWKIA2493ZZ
SectionMeasurement Standard
A – A Clearance
4.6 ± 1.0 (0.18 ± 0.04)
Surface height 0.0 ± 1.0 (0.0 ± 0.04)
B – B Clearance
4.6 ± 2.0 (0.18 ± 0.08)
Surface height 0.0 ± 1.5 (0.0 ± 0.06)
C – C Clearance
4.6 ± 1.0 (0.18 ± 0.04)
Surface height 0.0 ± 1.0 (0.0 ± 0.04)
Revision: August 2015 2016 Versa Note

cardiagn.com