NISSAN TEANA 2003 Service Manual

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI

FA I L - S A F E
Solution When Communication Error Between the Unified Meter and A/C Amp. and the Com-
bination Meter
Function Specifications
SpeedometerReturn to zero when discontinuing communication or receiv-
ing irregular data.
Tachometer
Reset to zero by suspending communication.
Fuel gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
Shift indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lampLow water temperature indicator lamp
The lamp turns on by suspending communication. VDC OFF indicator (With VDC)
SLIP indicator (With VDC)
Brake warning lamp
ABS warning lamp
ASCD CRUISE indicator lamp
The lamp turns off by suspending communication. ASCD SET indicator lamp
Turn signal indicator lamp
High-beam indicator lamp
Front fog indicator lamp
Rear fog indicator lamp
Oil pressure warning lamp
Door warning lamp
High water temperature warning lamp
Malfunction indicator lamp
A/T CHECK warning lamp
CVT indicator lamp
KEY warning lamp
LOCK warning lamp

DI-6
COMBINATION METERS

HOW TO CHANGE THE DISPLAY FOR ODO/TRIP METER

The vehicle speed signal and the memory signals from the meter memory circuit are processed by the
combination meter and the mileage is displayed.

Depressing the odo/trip meter switch toggles the mode in the following order.

The odo/trip meter display mode toggling and trip display resetting can be identified by the amount of time
that elapses from pressing the odo/trip meter switch to releasing it.

When resetting with trip A displayed, only trip A display is reset (The same way for “trip B”).
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times

through 10A fuse [No. 19, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 21,

through 15A fuse [No. 17, located in the fuse block (J/B)]

to combination meter terminal 7.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 35.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 14, located in the fuse block (J/B)]

to combination meter terminal 8,

through 10A fuse [No. 12, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 22.
With the ignition switch in the ON position, power is supplied

through 15A fuse [No. 10, located in the fuse block (J/B)], and

through 15A fuse [No. 11, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 46.
Ground is supplied

to combination meter terminals 10, 11 and 12

through body grounds M71 and M72,

to unified meter and A/C amp. terminals 29 and 30

through body grounds M71 and M72.
SEL175W

COMBINATION METERS
DI-7
C
D
E
F
G
H
I
J
L
MA
B
DI

SPEEDOMETER
ABS actuator and electric unit (control unit) provides a vehicle speed signal to the unified meter and A/C amp.
with CAN communication line. After unified meter and A/C amp. received the vehicle speed signal, it changes
the signal to 8 pulse signal and provides the 8 pulse signal to the combination meter for the speedometer.
TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm).
ECM provides an engine speed signal to unified meter and A/C amp. with CAN communication line. Unified
meter and A/C amp. provides an engine speed signal to combination meter for tachometer with communica-
tion line between unified meter and A/C amp. and combination meter.
LOW WATER TEMPERATURE INDICATOR LAMP, HIGH WATER TEMPERATURE WARNING
LAMP
ECM converts water temperature signal from water temperature sensor into data and transmits the data to uni-
fied meter and A/C amp. with CAN communication line. Unified meter and A/C amp. transmit the received
water temperature signal to the combination meter with communication line between unified meter and A/C
amp. and combination meter. Combination meter turns on/off low water temperature indicator lamp or high
water temperature warning lamp through the received water temperature signal.
FUEL GAUGE
The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by a variable ground signal supplied

from unified meter and A/C amp. terminal 36

through the fuel level sensor unit and fuel pump terminals 5 and 2

to unified meter and A/C amp. terminal 28 for the fuel gauge.
Unified meter and A/C amp. provides a fuel level signal to combination meter for fuel gauge with communica-
tion line between unified meter and A/C amp. and combination meter.
Component Parts and Harness Connector LocationBKS001RY
SKIB0770E

DI-8
COMBINATION METERS

Arrangement of Combination MeterBKS001RZ
PKIC9724E

COMBINATION METERS
DI-9
C
D
E
F
G
H
I
J
L
MA
B
DI

Internal CircuitBKS001S0
TKWM4624E

DI-10
COMBINATION METERS

Wiring Diagram — METER —BKS001S1
TKWM4625E

COMBINATION METERS
DI-11
C
D
E
F
G
H
I
J
L
MA
B
DI

TKWM4832E

DI-12
COMBINATION METERS

Terminals and Reference Value for Combination MeterBKS001S2
TerminalWire
colorItemCondition
Reference value
Ignition
switchOperation or condition
7 Y/R Battery power supply OFF — Battery voltage
8 P Ignition switch ON or START ON — Battery voltage
10
B Ground ON — Approx. 0V 11
12
17 V Ignition switch ACC or ON ACC — Battery voltage
18 G/BTX communication line (To
unified meter and A/C amp.)ON —
19 RRX communication line (From
unified meter and A/C amp.)ON —
20 V/WVehicle speed signal
(8-pulse)ONSpeedometer operated
[When vehicle speed is
approx. 40 km/h (25 MPH)]NOTE:
Maximum voltage may be 12V
due to specifications (connected
units).
SKIA3361E
SKIA3362E
SKIA6649J

COMBINATION METERS
DI-13
C
D
E
F
G
H
I
J
L
MA
B
DI

Terminals and Reference Value for Unified Meter and A/C Amp.BKS001S3
Self-Diagnosis Mode of Combination MeterBKS001S4
SELF-DIAGNOSIS MODE FUNCTION

Odo/trip meter segment and shift indicator segment operation can be checked in self-diagnosis mode.

Meter/gauge can be checked in self-diagnosis mode.
OPERATION PROCEDURE
1. Turn the ignition switch ON, and switch the odo/trip meter to “trip A” or “trip B”.
NOTE:
If the diagnosis function is activated with the “trip A” displayed, the mileage on the “trip A” will indicate
0000.0, but the actual trip mileage will be retained. (Trip same way for “trip B”.)
2. Turn ignition switch OFF.
3. While pushing the odo/trip meter switch, turn ignition switch ON again.
4. Make sure that the trip meter displays “0000.0”.
TerminalWire
colorItemCondition
Reference value
Ignition
switchOperation or condition
1 L CAN- H — — —
9RTX communication line (To
combination meter)ON —
11 P C A N - L — — —
19 G/BRX communication line
(From combination meter)ON —
21 Y/R Battery power supply OFF — Battery voltage
22 GIgnition switch ON or
STARTON — Battery voltage
26 V/WVehicle speed signal
(8-pulse)ONSpeedometer operated
[When vehicle speed is
approx. 40 km/h (25 MPH)]NOTE:
Maximum voltage may be 12V due to
specifications (connected units).
28 G/O Fuel level sensor signal — —Refer to DI-24, "
CHECK FUEL LEVEL
SENSOR UNIT" .
29 B Ground (for power) ON — Approx. 0V
30 B Ground ON — Approx. 0V
35 V Ignition switch ACC or ON ACC — Battery voltage
36 B/W Fuel level sensor ground ON — Approx. 0V
46 W/L Ignition switch ON ON — Battery voltage
SKIA3362E
SKIA3361E
SKIA6649J

DI-14
COMBINATION METERS

5. Press the odo/trip meter switch at least 3 times (within 7 seconds after the ignition switch is turned ON).
6. All the segments on the odo/trip meter and shift indicator illuminate, and simultaneously the low-fuel warn-
ing lamp indicator illuminates. At this time, the unified meter control unit is turned to diagnosis mode.
NOTE:

A/T MODELS (1)

CVT MODELS (2)
7. Each meter activates during pressing odo/trip meter switch. (At this time, the low-fuel warning lamp goes
off, low water temperature indicator lamp and high water temperature warning lamp goes on.)
NOTE:
The figure is reference.
CONSULT-II FunctionBKS001S5
Refer to DI-29, "CONSULT-II Function (METER A/C AMP)" in “UNIFIED METER AND A/C AMP”.
Trouble DiagnosisBKS001S6
HOW TO PROCEED WITH TROUBLE DIAGNOSIS
1. Confirm the symptom or customer complaint.
2. Perform preliminary check. Refer to DI-15, "
PRELIMINARY CHECK" .
3. According to the symptom chart, repair or replace the cause of the symptom.
4. Does the meter operate normally? If so, GO TO 5. If not, GO TO 3.
5. INSPECTION END
PKIC8364J
SKIB0773E