lock NISSAN TEANA 2003 Service Manual

WATER PUMP
CO-47
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
CO

10. Remove water drain plug (front) on water pump side of cylinder
block to drain engine coolant from engine inside.
11. Remove chain tensioner cover and water pump cover from front timing chain case.

U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] o r e q u i v a l e n t t o o l t o c u t l i q u i d g a s k e t f o r r e m o v e .
12. Remove idler pulley and bracket. Refer to EM-173, "
TIMING CHAIN" .
13. Remove timing chain tensioner (primary) as follows:
a. Remove lower mounting bolt.
b. Loosen upper mounting bolt slowly, and then turn timing chain
tensioner (primary) on the mounting bolt so that plunger is fully
expanded.
NOTE:
Even if plunger is fully expanded, it is not dropped from the body
of timing chain tensioner (primary).
c. Remove upper mounting bolt, and then remove timing chain ten-
sioner (primary).
CAUTION:
Be careful not to drop mounting bolts inside timing chain
case.
14. Remove water pump as follows:
a. Remove three water pump mounting bolts. Secure a gap
between water pump gear and timing chain, by turning crank-
shaft pulley counterclockwise until timing chain looseness on
water pump sprocket becomes maximum.
b. Screw M8 bolts [pitch: 1.25 mm (0.049 in) length: Approx. 50
mm (1.97 in)] into water pumps upper and lower mounting bolt
holes until they reach timing chain case. Then, alternately
tighten each bolt for a half turn, and pull out water pump.
CAUTION:

Pull straight out while preventing vane from contacting
socket in installation area.

Remove water pump without causing sprocket to contact
timing chain.
c. Remove M8 bolts and O-rings from water pump.
CAUTION:
Do not disassemble water pump.
INSPECTION AFTER REMOVAL

Check for badly rusted or corroded water pump body assembly.
PBIC2516E
PBIC3562E
PBIC1193E
JLC357B

WATER PUMP
CO-49
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
CO

e. Install timing chain tensioner (primary).

Remove any dirt and foreign materials completely from the
back and the mounting surfaces of timing chain tensioner (pri-
mary).
f. Pull out stopper pin after installing, and then release plunger.
g. Make sure again that timing chain and water pump sprocket are
engaged.
4. Install chain tensioner cover and water pump cover as follows:
a. Before installing, remove all traces of old liquid gasket from mat-
ing surface of water pump cover and chain tensioner cover
using scraper. Also remove traces of old liquid gasket from the
mating surface of front timing chain case.
b. Apply a continuous bead of liquid gasket with tube presser [SST:
WS39930000] to mating surface of chain tensioner cover and
water pump cover.
Use Genuine Liquid Gasket or equivalent.
CAUTION:
Attaching should be done within 5 minutes after coating.
c. Tighten mounting bolts.
5. Install water drain plug (front) on water pump side of cylinder block.

Apply liquid gasket to the thread of water drain plug (front).
Use Genuine Liquid Gasket or equivalent.
6. Install in the reverse order of removal in this step.
NOTE:
If hydraulic pressure inside timing chain tensioner drops after removal/installation, slack in guide may gen-
erate a pounding noise during and just after engine start. However, this does not indicate an unusualness.
Noise will stop after hydraulic pressure rises.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant using radiator cap tester adapter [SST: EG17650301] and radiator cap
tester (commercial service tool). Refer to CO-34, "
LEAK CHECK" .

Start and warm up engine. Visually check if there is no leaks of engine coolant.
PBIC3569E
SLC446B
PBIC2650E

CO-50
[VQ]
WATER INLET AND THERMOSTAT ASSEMBLY

WATER INLET AND THERMOSTAT ASSEMBLYPFP:21200
Removal and InstallationBBS004X7
REMOVAL
1. Drain engine coolant from radiator drain plug at the bottom of radiator, and from water drain plug at the
front of cylinder block. Refer to CO-34, "
Changing Engine Coolant" and CO-46, "WATER PUMP" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
2. Remove reservoir tank of radiator, and move it aside.
3. Disconnect radiator hose (lower) from water inlet and thermostat assembly.
4. Disconnect oil cooler water hose from water inlet and thermostat assembly. (VQ35DE)
5. Remove water inlet and thermostat assembly.
CAUTION:
Do not disassemble water inlet and thermostat assembly.
Replace them as a unit, if necessary.
1. Gasket 2. Water inlet and thermostat assembly 3. Radiator hose (lower)
4. Water hose
PBIC2517E
SLC962AB

CO-52
[VQ]
WATER OUTLET AND WATER PIPING

WATER OUTLET AND WATER PIPINGPFP:11060
Removal and InstallationBBS004X8

Refer to GI-10, "Components" for symbol marks in the figure.
REMOVAL
1. Remove engine cover. Refer to EM-133, "INTAKE MANIFOLD COLLECTOR" .
2. Drain engine coolant from radiator drain plug at the bottom of radiator, and from water drain plug at the
front of cylinder block. Refer to CO-34, "
Changing Engine Coolant" and CO-46, "WATER PUMP" .
CAUTION:

Perform this step when engine is cold.

Do not spill engine coolant on drive belts.
3. Remove air duct (inlet), air cleaner case (upper) with mass air flow sensor and air duct assembly. Refer to
EM-131, "
AIR CLEANER AND AIR DUCT" .
4. Remove radiator hose (upper).
5. Remove water hoses and heater hoses.
6. Disconnect harness connectors, and move harness to aside.
1. Radiator hose (upper) 2. Washer 3. Engine coolant temperature sensor
4. Heater hose 5. Water outlet 6. Water hose
7. Gasket 8. Water hose 9. Gasket
10. Water connector 11. O-ring 12. Heater pipe
13. Heater hose 14. Water bypass pipe 15. Water hose
A. To heater core B. To intake manifold collector (upper) C. To intake manifold collector (upper)
D.To heater core (VQ23DE)
To CVT fluid cooler valve (VQ35DE)E. To radiator
PBIC4583J

CVT-1
CVT
C TRANSMISSION/TRANSAXLE
CONTENTS
D
E
F
G
H
I
J
K
L
M
SECTION CVT
A
B
CVT

CVT
INDEX FOR DTC ........................................................ 6
Alphabetical Index .................................................... 6
DTC No. Index ......................................................... 7
PRECAUTIONS .......................................................... 8
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 8
Precautions Necessary for Steering Wheel Rotation
After Battery Disconnect .......................................... 8
OPERATION PROCEDURE ................................. 8
Precautions for TCM and CVT Assembly Replace-
ment ......................................................................... 9
EEPROM ERASING PATTERNS .......................... 9
METHOD FOR ERASING THE EEPROM IN THE
TCM ...................................................................... 9
METHOD FOR WRITING DATA FROM THE
ROM ASSEMBLY IN THE TRANSAXLE .............. 9
CHECK METHOD ................................................. 9
Removal and Installation Procedure for CVT Unit
Connector ............................................................... 10
REMOVAL ........................................................... 10
INSTALLATION ................................................... 10
Precautions ............................................................. 11
PREPARATION ......................................................... 12
Special Service Tools ............................................. 12
Commercial Service Tools ...................................... 12
CVT FLUID ............................................................... 13
Checking CVT Fluid ............................................... 13
Changing CVT Fluid ............................................... 14
CVT SYSTEM ........................................................... 15
Cross-Sectional View - RE0F09A .......................... 15
Control System ....................................................... 16
Hydraulic Control System ....................................... 17
TCM Function ......................................................... 18
CONTROL SYSTEM OUTLINE .......................... 18
CONTROL SYSTEM DIAGRAM ......................... 18
CAN Communication .............................................. 19
SYSTEM DESCRIPTION .................................... 19
Input/Output Signal of TCM .................................... 19Line Pressure and Secondary Pressure Control .... 20
NORMAL CONTROL .......................................... 20
FEEDBACK CONTROL ...................................... 20
Shift Control ............................................................ 20
“D” POSITION ..................................................... 21
“M” POSITION ..................................................... 21
DOWNHILL ENGINE BRAKE CONTROL (AUTO
ENGINE BRAKE CONTROL) .............................. 21
ACCELERATION CONTROL .............................. 21
Lock-up and Select Control .................................... 21
TORQUE CONVERTER CLUTCH AND SELECT
CONTROL VALVE CONTROL ............................ 22
Control Valve .......................................................... 23
FUNCTION OF CONTROL VALVE ..................... 23
TROUBLE DIAGNOSIS ............................................ 24
DTC Inspection Priority Chart ................................. 24
Fail-safe .................................................................. 24
FAIL-SAFE FUNCTION ....................................... 24
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 25
INTRODUCTION ................................................. 25
WORK FLOW ...................................................... 26
DIAGNOSTIC WORKSHEET .............................. 27
CVT Electrical Parts Location ................................. 30
Circuit Diagram ....................................................... 31
Inspections Before Trouble Diagnosis .................... 32
CVT FLUID CHECK ............................................ 32
STALL TEST ........................................................ 32
LINE PRESSURE TEST ..................................... 33
Road Test ............................................................... 35
DESCRIPTION .................................................... 35
CONSULT-II OPERATION PROCEDURE ........... 35
Check Before Engine Is Started ............................. 37
Check at Idle ........................................................... 37
Cruise Test .............................................................. 38
Vehicle Speed at Which Gear Shifting Occurs ....... 40
TCM Input/Output Signal Reference Values ........... 40
TCM TERMINAL CONNECTOR LAYOUT .......... 40

CVT-2 TCM INSPECTION TABLE .................................. 40
CONSULT-II Function (TRANSMISSION) .............. 43
FUNCTION .......................................................... 43
CONSULT-II REFERENCE VALUE ..................... 43
CONSULT-II SETTING PROCEDURE ................ 45
WORK SUPPORT MODE ................................... 45
SELF-DIAGNOSTIC RESULT MODE ................. 47
DATA MONITOR MODE ...................................... 50
CAN DIAGNOSTIC SUPPORT MONITOR
MODE .................................................................. 52
DTC U1000 CAN COMMUNICATION LINE .............. 53
Description .............................................................. 53
On Board Diagnosis Logic ...................................... 53
Possible Cause ....................................................... 53
DTC Confirmation Procedure ................................. 53
WITH CONSULT-II .............................................. 53
Wiring Diagram — CVT — CAN ............................. 54
Diagnostic Procedure ............................................. 55
DTC P0615 START SIGNAL CIRCUIT ..................... 56
Description .............................................................. 56
CONSULT-II Reference Value ................................ 56
On Board Diagnosis Logic ...................................... 56
Possible Cause ....................................................... 56
DTC Confirmation Procedure ................................. 56
WITH CONSULT-II .............................................. 56
Wiring Diagram — CVT — STSIG .......................... 57
Diagnostic Procedure ............................................. 58
DTC P0703 STOP LAMP SWITCH CIRCUIT ........... 60
Description .............................................................. 60
CONSULT-II Reference Value ................................ 60
On Board Diagnosis Logic ...................................... 60
Possible Cause ....................................................... 60
DTC Confirmation Procedure ................................. 60
WITH CONSULT-II .............................................. 60
Diagnostic Procedure ............................................. 61
DTC P0705 PARK/NEUTRAL POSITION SWITCH ... 62
Description .............................................................. 62
CONSULT-II Reference Value ................................ 62
On Board Diagnosis Logic ...................................... 62
Possible Cause ....................................................... 62
DTC Confirmation Procedure ................................. 62
WITH CONSULT-II .............................................. 63
Wiring Diagram — CVT — PNP/SW ...................... 64
Diagnostic Procedure ............................................. 66
Component Inspection ............................................ 68
PNP SWITCH ...................................................... 68
DTC P0710 CVT FLUID TEMPERATURE SENSOR
CIRCUIT .................................................................... 69
Description .............................................................. 69
CONSULT-II Reference Value ................................ 69
On Board Diagnosis Logic ...................................... 69
Possible Cause ....................................................... 69
DTC Confirmation Procedure ................................. 69
WITH CONSULT-II .............................................. 69
Wiring Diagram — CVT — FTS .............................. 70
Diagnostic Procedure ............................................. 71
Component Inspection ............................................ 73
CVT FLUID TEMPERATURE SENSOR .............. 73
DTC P0715 INPUT SPEED SENSOR CIRCUIT (PRI SPEED SENSOR) ..................................................... 74
Description .............................................................. 74
CONSULT-II Reference Value ................................. 74
On Board Diagnosis Logic ...................................... 74
Possible Cause ....................................................... 74
DTC Confirmation Procedure .................................. 74
WITH CONSULT-II ............................................... 74
Wiring Diagram — CVT — PRSCVT ...................... 75
Diagnostic Procedure .............................................. 76
DTC P0720 VEHICLE SPEED SENSOR CVT (SEC-
ONDARY SPEED SENSOR) ..................................... 79
Description .............................................................. 79
CONSULT-II Reference Value ................................. 79
On Board Diagnosis Logic ...................................... 79
Possible Cause ....................................................... 79
DTC Confirmation Procedure .................................. 79
WITH CONSULT-II ............................................... 79
Wiring Diagram — CVT — SESCVT ...................... 80
Diagnostic Procedure .............................................. 81
DTC P0725 ENGINE SPEED SIGNAL ...................... 85
Description .............................................................. 85
CONSULT-II Reference Value ................................. 85
On Board Diagnosis Logic ...................................... 85
Possible Cause ....................................................... 85
DTC Confirmation Procedure .................................. 85
WITH CONSULT-II ............................................... 85
Diagnostic Procedure .............................................. 85
DTC P0730 BELT DAMAGE ..................................... 87
Description .............................................................. 87
CONSULT-II Reference Value ................................. 87
On Board Diagnosis Logic ...................................... 87
Possible Cause ....................................................... 87
DTC Confirmation Procedure .................................. 87
WITH CONSULT-II ............................................... 87
Diagnostic Procedure .............................................. 88
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................... 89
Description .............................................................. 89
CONSULT-II Reference Value ................................. 89
On Board Diagnosis Logic ...................................... 89
Possible Cause ....................................................... 89
DTC Confirmation Procedure .................................. 89
WITH CONSULT-II ............................................... 89
Wiring Diagram — CVT — TCV .............................. 90
Diagnostic Procedure .............................................. 91
Component Inspection ............................................ 93
TORQUE CONVERTER CLUTCH SOLENOID
VALVE .................................................................. 93
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) ... 94
Description .............................................................. 94
CONSULT-II Reference Value ................................. 94
On Board Diagnosis Logic ...................................... 94
Possible Cause ....................................................... 94
DTC Confirmation Procedure .................................. 94
WITH CONSULT-II ............................................... 94
Diagnostic Procedure .............................................. 95
DTC P0745 LINE PRESSURE SOLENOID VALVE ... 97
Description .............................................................. 97
CONSULT-II Reference Value ................................. 97

CVT-4 On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ...............................143
WITH CONSULT-II ............................................143
Diagnostic Procedure ...........................................144
DTC P1726 ELECTRIC THROTTLE CONTROL
SYSTEM ..................................................................145
Description ............................................................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ...............................145
WITH CONSULT-II ............................................145
Diagnostic Procedure ...........................................146
DTC P1740 LOCK-UP SELECT SOLENOID VALVE
CIRCUIT ..................................................................147
Description ............................................................147
CONSULT-II Reference Value ..............................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ...............................147
WITH CONSULT-II ............................................147
Wiring Diagram — CVT — L/USSV ......................148
Diagnostic Procedure ...........................................149
Component Inspection ..........................................151
LOCK-UP SELECT SOLENOID VALVE ............151
DTC P1745 LINE PRESSURE CONTROL .............152
Description ............................................................152
On Board Diagnosis Logic ....................................152
Possible Cause .....................................................152
DTC Confirmation Procedure ...............................152
WITH CONSULT-II ............................................152
Diagnostic Procedure ...........................................152
DTC P1777 STEP MOTOR - CIRCUIT ...................153
Description ............................................................153
CONSULT-II Reference Value ..............................153
On Board Diagnosis Logic ....................................153
Possible Cause .....................................................153
DTC Confirmation Procedure ...............................153
WITH CONSULT-II ............................................153
Wiring Diagram — CVT — STM ...........................154
Diagnostic Procedure ...........................................155
Component Inspection ..........................................156
STEP MOTOR ...................................................156
DTC P1778 STEP MOTOR - FUNCTION ...............157
Description ............................................................157
CONSULT-II Reference Value ..............................157
On Board Diagnosis Logic ....................................157
Possible Cause .....................................................157
DTC Confirmation Procedure ...............................157
WITH CONSULT-II ............................................157
Diagnostic Procedure ...........................................158
CVT INDICATOR CIRCUIT .....................................159
Description ............................................................159
CONSULT-II Reference Value ..............................159
Diagnostic Procedure ...........................................159
CVT INDICATOR SYMPTOM CHART ...............159
TROUBLE DIAGNOSIS FOR SYMPTOMS ............160Wiring Diagram — CVT — NONDTC ...................160
CVT Indicator Lamp Does Not Come On ..............164
SYMPTOM: ........................................................164
DIAGNOSTIC PROCEDURE .............................164
Engine Cannot Be Started in “P” or “N” Position ...165
SYMPTOM: ........................................................165
DIAGNOSTIC PROCEDURE .............................165
In “P” Position, Vehicle Moves Forward or Backward
When Pushed .......................................................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
In “N” Position, Vehicle Moves ..............................166
SYMPTOM: ........................................................166
DIAGNOSTIC PROCEDURE .............................166
Large Shock “N” → “R” Position ...........................167
SYMPTOM: ........................................................167
DIAGNOSTIC PROCEDURE .............................167
Vehicle Does Not Creep Backward in “R” Position .168
SYMPTOM: ........................................................168
DIAGNOSTIC PROCEDURE .............................168
Vehicle Does Not Creep Forward in “D” Position ..169
SYMPTOM: ........................................................169
DIAGNOSTIC PROCEDURE .............................169
CVT Does Not Shift ...............................................170
SYMPTOM: ........................................................170
DIAGNOSTIC PROCEDURE .............................170
Cannot Be Changed to Manual Mode ...................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
CVT Does Not Shift in Manual Mode ....................171
SYMPTOM: ........................................................171
DIAGNOSTIC PROCEDURE .............................171
Vehicle Does Not Decelerate by Engine Brake .....172
SYMPTOM: ........................................................172
DIAGNOSTIC PROCEDURE .............................172
TRANSMISSION CONTROL MODULE ..................174
Removal and Installation .......................................174
COMPONENTS .................................................174
REMOVAL ..........................................................174
INSTALLATION ..................................................175
SHIFT CONTROL SYSTEM ....................................176
Removal and Installation .......................................176
CONTROL DEVICE COMPONENTS ................176
CONTROL CABLE COMPONENTS ..................177
REMOVAL ..........................................................177
INSTALLATION ..................................................178
Adjustment of CVT Position ..................................178
Checking of CVT Position .....................................179
CVT SHIFT LOCK SYSTEM ...................................180
Description ............................................................180
Shift Lock System Electrical Parts Location ..........180
Wiring Diagram — CVT — SHIFT ........................181
Shift Lock Control Unit Reference Values .............183
SHIFT LOCK HARNESS CONNECTOR TERMI-
NALS LAYOUT ..................................................183
SHIFT LOCK CONTROL UNIT INSPECTION

CVT-5
D
E
F
G
H
I
J
K
L
MA
B
CVT
TABLE ............................................................... 183
Component Inspection ......................................... 184
SHIFT LOCK SOLENOID ................................. 184
DETENTION SWITCH (FOR KEY) ................... 184
DETENTION SWITCH (FOR SHIFT) ................ 184
KEY LOCK SOLENOID ..................................... 184
IGNITION KNOB SWITCH ................................ 185
STOP LAMP SWITCH ...................................... 185
AIR BREATHER HOSE .......................................... 186
Removal and Installation ...................................... 186
COMPONENTS ................................................ 186
REMOVAL ......................................................... 186
INSTALLATION ................................................. 186
DIFFERENTIAL SIDE OIL SEAL ........................... 187
Removal and Installation ...................................... 187
COMPONENTS ................................................ 187
REMOVAL ......................................................... 187
INSTALLATION ................................................. 188CVT FLUID COOLER SYSTEM ..............................189
CVT Fluid Cooler Removal and Installation ..........189
COMPONENTS .................................................189
REMOVAL .........................................................190
INSTALLATION .................................................192
COMPONENT INSPECTION ............................192
TRANSAXLE ASSEMBLY ......................................193
Removal and Installation ......................................193
COMPONENTS .................................................193
REMOVAL .........................................................194
INSPECTION ....................................................196
INSTALLATION .................................................196
SERVICE DATA AND SPECIFICATIONS (SDS) ....198
General Specifications ..........................................198
Vehicle Speed at Which Gear Shifting Occurs .....198
Stall Speed ...........................................................198
Line Pressure .......................................................198
Solenoid Valves ....................................................198
CVT Fluid Temperature Sensor ............................199
Primary Speed Sensor .........................................199
Secondary Speed Sensor .....................................199
Removal and Installation ......................................199

CVT-8
PRECAUTIONS

PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BCS001NA
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectBCS001NB
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-II to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-II.

CVT-10
PRECAUTIONS

Removal and Installation Procedure for CVT Unit ConnectorBCS001FS
REMOVAL
Rotate bayonet ring counterclockwise, pull out CVT unit harness
connector upward and remove it.
INSTALLATION
1. Align ∆ marking on CVT unit harness connector terminal body
with
❏ marking on bayonet ring, insert CVT unit harness con-
nector, and then rotate bayonet ring clockwise.
2. Rotate bayonet ring clockwise until ∆ marking on CVT unit har-
ness connector terminal body is aligned with the slit on bayonet
ring as shown in the figure (correctly fitting condition), install
CVT unit harness connector to CVT unit harness connector ter-
minal body.
CAUTION:

Securely align ∆ marking on CVT unit harness connector
terminal body with bayonet ring slit. Then, be careful not
to make a half fit condition as shown in the figure.

Do not mistake the slit of bayonet ring for other dent por-
tion.
SCIA2096E
SCIA2097E
SCIA2098E
SCIA2099E