NISSAN TEANA 2008 Service Manual

SRC-8
< FUNCTION DIAGNOSIS >
SRS AIR BAG SYSTEM
3. Detects and records the deployment of air bag and seat belt pre-tensioner, and turns on air bag warning
lamp.
4. Indicates malfunctioning portion with blinking times of air bag warning lamp in diagnosis mode.
5. Indicates the malfunctioning record by CONSULT-III.
Component Parts LocationINFOID:0000000003813932
Component DescriptionINFOID:0000000003813933
 Air bag diagnosis sensor units are prepared for operation while the ignition switch is in the ON or START
position.
 The operation of Supplemental Restraint System is different from collision modes application. For example,
the driver air bag module and front passenger air bag module are activated in a frontal collision but not in a
side collision.
 SRS configurations which are activated for some collision modes are as follows.
1. Front passenger air bag module M62 2. Driver air bag module M350 3. Conbination switch (Spiral cable)
M32
4. Air bag diagnosis sensor unit B14,
B228, M595. LH/RH satellite sensor
LH B37
 RH B2116. Front LH/RH seat belt pre-tensioner
LH B36
RH B213
7. Front LH/RH side air bag module
LH B16
 RH B2128. Crash zone sensor E313 9. Combination meter (Air bag warning
lamp) M34
10. LH/RH side curtain air bag module
LH B72
 RH B256
JMHIA0599ZZ
SRS configuration Frontal collision Left side collision Right side collision
Driver air bag module. Refer to SRC-122, "
Diagnosis
Procedure"×——
Front passenger air bag module. Refer to SRC-122,
"Diagnosis Procedure"×——

SRS AIR BAG SYSTEM
SRC-9
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
×: Application, —: No application
Front LH seat belt pre-tensioner. Refer to SRC-122,
"Diagnosis Procedure"×——
Front RH seat belt pre-tensioner. Refer to SRC-122,
"Diagnosis Procedure"×——
Front LH side air bag module. Refer toSRC-124, "
Di-
agnosis Procedure" —×—
Front RH side air bag module. Refer to SRC-124, "
Di-
agnosis Procedure"——×
LH side curtain air bag module. Refer to SRC-124,
"Diagnosis Procedure"—×—
RH side curtain air bag module. Refer to SRC-124,
"Diagnosis Procedure"——× SRS configuration Frontal collision Left side collision Right side collision

SRC-10
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (AIRBAG)
DIAGNOSIS SYSTEM (AIRBAG)
Diagnosis DescriptionINFOID:0000000003813934
CAUTION:
• Never use electrical test equipment on any circuit related to the SRS unless instructed in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
 Never repair, splice or modify the SRS wiring harness. If the harness is damaged, replace it with a
new one.
 Keep ground portion clean.
DIAGNOSIS FUNCTION
 The SRS self-diagnosis results can be read by using air bag warning lamp and/or CONSULT-III.
 The user mode is exclusively prepared for the customer (driver). This mode warns the driver of a system
malfunction through the operation of the air bag warning lamp.
 The diagnosis mode allows the technician to locate and inspect the malfunctioning part.
 The mode applications for the air bag warning lamp and CONSULT-III are as follows.
HOW TO PERFORM TROUBLE DIAGNOSIS FOR QUICK AND ACCURATE REPAIR
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate.
In general, each customer feels differently about a malfunction. It is important to fully understand the symp-
toms or conditions for a customer complaint.
Information from Customer.
 WHAT..... Vehicle model.
 WHEN..... Date, Frequency.
 WHERE..... Road conditions.
 HOW..... Operating conditions, Symptoms.
Preliminary Check.
Check that the following parts are in good order.
 Battery (Refer to PG-3, "
How to Handle Battery").
 Fuse (Refer to PG-82, "
Fuse").
 System component-to-harness connections.
Air Bag Warning Lamp DiagnosisINFOID:0000000003843289
SELF-DIAGNOSIS FUNCTION
 The reading of these results is accomplished by “User mode” and “Diagnosis mode”.
 After a malfunction is repaired, turn ignition switch ON. Diagnosis mode returns to the User mode. At that
time, the self-diagnosis result is cleared.
User mode Diagnosis mode Display type
Air bag warning lamp X X ON-OFF operation
CONSULT-III – X Monitoring

DIAGNOSIS SYSTEM (AIRBAG)
SRC-11
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P HOW TO CHANGE SELF-DIAGNOSIS MODE WITHOUT CONSULT-III
DIAGNOSTIC PROCEDURE (USER MODE)
Checking air bag operation according to air bag warning lamp-User mode
1. Turn the ignition switch from OFF to ON, and check that the air bag warning lamp blinks.
2. Compare the air bag warning lamp blinking pattern with the
examples.
PHIA0709E
BF-1845D

SRC-12
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (AIRBAG)
Air bag warning lamp examples (User mode)
DIAGNOSTIC PROCEDURE (DIAGNOSIS MODE)
1. Turn the ignition switch ON, and check that the air bag warning lamp blinks.
2. There are 2 blinking patterns for the air bag warning lamp. One is a 3-second blink followed by a 0.5- sec-
ond blink repeat. The other is two 1.5-second blinks followed by a 0.5-second blink repeat.
Air bag warning lamp operation -User mode SRS condition Reference item
 No malfunction is detected
 No further action is necessary—
The system is malfunctioning and
needs to be repaired as indicatedGo to SRC-10, "
Air Bag Warning
Lamp Diagnosis"
 Air bag is deployed
 Seat belt pre-tensioner is deployedGo to SRC-122, "Diagnosis Proce-
dure" or SRC-124, "Diagnosis Pro-
cedure"
 Air bag diagnosis sensor unit is mal-
functioning
 Air bag power supply circuit is mal-
functioning
 Air bag warning lamp circuit is mal-
functioningGo to SRC-145, "
Diagnosis Proce-
dure"
 Air bag diagnosis sensor unit is mal-
functioning
 Air bag warning lamp circuit is mal-
functioningGo to SRC-146, "
Diagnosis Proce-
dure"
SHIA0011E
SHIA0012E
SHIA0013E
SHIA0014E

DIAGNOSIS SYSTEM (AIRBAG)
SRC-13
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P An Example of a 3-second Blink Followed by a 0.5-second Blink Repeat
a through b are repeated.
b: Seven 0.5-second blinks indicate that the air bag diagnosis sensor unit circuit is malfunctioning.
Number of 0.5-second Blinks After a 3-second Blink Indicates Malfunctioning Items
JMHIA0640GB
Number of 0.5-second blinks Malfunctioning items Blinking pattern
0 Self-diagnosis result is not deleted —
1 Front LH seat belt pre-tensionerRefer to the following
SRC-60, "
DTC Logic"
SRC-62, "DTC Logic"
SRC-64, "DTC Logic"
SRC-66, "DTC Logic"
2 Driver air bag moduleRefer to the following
SRC-32, "
DTC Logic"
SRC-34, "DTC Logic"
SRC-36, "DTC Logic"
SRC-38, "DTC Logic"
3 Front RH seat belt pre-tensionerRefer to the following
SRC-52, "
DTC Logic"
SRC-54, "DTC Logic"
SRC-56, "DTC Logic"
SRC-58, "DTC Logic"
6 Crash zone sensorRefer to the following
SRC-24, "DTC Logic"
SRC-26, "DTC Logic"
SRC-28, "DTC Logic"
7 Air bag diagnosis sensor unitRefer to the following
SRC-16, "
DTC Logic"
SRC-18, "DTC Logic"
SRC-20, "DTC Logic"
SRC-22, "DTC Logic"
SRC-30, "DTC Logic"
SRC-40, "DTC Logic"
SRC-50, "DTC Logic"
SRC-70, "DTC Logic"
SRC-80, "DTC Logic"
SRC-98, "DTC Logic"
SRC-120, "DTC Logic"
SRC-68, "DTC Logic"
SRC-118, "DTC Logic"
SRC-130, "DTC Logic"

SRC-14
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (AIRBAG)
An Example of Two 1.5-second Blinks Followed by a 0.5-second Blink Repeat
a through b are repeated.
b: Six 0.5-second blinks indicate that the LH side curtain air bag module circuit is malfunctioning.
Number of 0.5-second Blinks After Two 1.5-second Blinks Indicates Malfunctioning Items
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
8 Front passenger air bag moduleRefer to the following
SRC-42, "
DTC Logic"
SRC-44, "DTC Logic"
SRC-46, "DTC Logic"
SRC-48, "DTC Logic"
17 Air bag diagnosis sensor unitRefer to the following
SRC-100, "DTC Logic"
Number of 0.5-second blinks Malfunctioning items Blinking pattern
JMHIA0641GB
Number of 0.5-second blinks Malfunctioning items Blinking pattern
1 Front LH side air bag moduleRefer to the following
SRC-90, "
DTC Logic"
SRC-92, "DTC Logic"
SRC-94, "DTC Logic"
SRC-96, "DTC Logic"
2 Front RH side air bag moduleRefer to the following
SRC-82, "
DTC Logic"
SRC-84, "DTC Logic"
SRC-86, "DTC Logic"
SRC-88, "DTC Logic"
3 RH satellite sensorRefer to the following
SRC-72, "DTC Logic"
SRC-74, "DTC Logic"
SRC-126, "DTC Logic"
4 LH satellite sensorRefer to the following
SRC-76, "DTC Logic"
SRC-78, "DTC Logic"
SRC-128, "DTC Logic"
5 RH side curtain air bag moduleRefer to the following
SRC-102, "
DTC Logic"
SRC-104, "DTC Logic"
SRC-106, "DTC Logic"
SRC-108, "DTC Logic"
6 LH side curtain air bag moduleRefer to the following
SRC-110, "
DTC Logic"
SRC-112, "DTC Logic"
SRC-114, "DTC Logic"
SRC-116, "DTC Logic"

DIAGNOSIS SYSTEM (AIRBAG)
SRC-15
< FUNCTION DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
After a malfunction is repaired, turn the ignition switch OFF for at least one second, then turn ignition switch
ON. Diagnosis mode returns to the user mode. At that time the self-diagnosis result is cleared.
CONSULT-III FunctionINFOID:0000000003813935
HOW TO CHANGE SELF-DIAGNOSIS MODE WITH CONSULT-III
From User Mode to Diagnosis Mode
After selecting “AIR BAG” on the “SELECT SYSTEM” screen, User mode automatically changes to Diagnosis
mode.
From Diagnosis Mode to User Mode
To return to User mode from Diagnosis mode, touch “BACK” key of CONSULT-III until “SELECT SYSTEM”
appears, then Diagnosis mode automatically changes to User mode.
DIAGNOSIS MODE FOR CONSULT-III
 “SELF-DIAG [CURRENT]”
Current self-diagnosis results (also indicated with the number of air bag warning lamp blinks in Diagnosis
mode) are displayed on CONSULT-III screen in real time. This refers to a malfunctioning part requiring
repairs.
 “SELF-DIAG [PAST]”
Diagnosis results previously stored in the memory are displayed on CONSULT-III screen. The stored results
are not erased until memory erasing is executed.
 “TROUBLE DIAG RECORD”
With TROUBLE DIAG RECORD, diagnosis results previously erased by a reset operation can be displayed
on CONSULT-III screen.
 “DISCRIMINATED NO.”
The air bag diagnosis sensor unit for each vehicle model has its own individual classification number. This
number is displayed on CONSULT-III screen. When replacing the air bag diagnosis sensor unit, refer to the
part number for the compatibility. After installation, replacement with a correct unit can be checked by con-
firming this classification number on CONSULT-III screen.
After repair, check that the discriminated number of air bag diagnosis sensor unit installed to vehicle is the
same. Refer to SR-22, "
Exploded View".
HOW TO ERASE SELF-DIAGNOSTIC RESULTS
 “SELF-DIAG [CURRENT]”
A current self-diagnosis result is displayed on CONSULT-III screen in real time.
After the malfunction is repaired completely, no malfunction is detected on “SELF-DIAG [CURRENT]”.
 “SELF-DIAG [PAST]”
Return to “SELF-DIAG [CURRENT]” CONSULT-III screen by touching “BACK” key of CONSULT-III and
select “SELF-DIAG [CURRENT]” in SELECT DIAG MODE. Touch “ERASE” in “SELF-DIAG [CURRENT]”
mode.
NOTE:
If the memory of the malfunction in “SELF-DIAG [PAST]” is not erased, the user mode shows the system
malfunction by illuminating the warning lamp even if the malfunction is repaired completely.
 “TROUBLE DIAG RECORD”
The memory of “TROUBLE DIAG RECORD” cannot be erased.

SRC-16
< COMPONENT DIAGNOSIS >
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
COMPONENT DIAGNOSIS
B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
DescriptionINFOID:0000000003813936
Check the whole SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
in the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.
OPERATION
It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally.
STRUCTURE
It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.
INSTALLATION
Air bag diagnosis sensor unit is installed under the center console with fixed bolts.
DTC LogicINFOID:0000000003813937
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAG RESULT
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “AIR BAG” Self Diagnostic Result.
Without CONSULT-III
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to SRC-10, "
Air Bag Warning Lamp Diagnosis".
NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.
Is malfunctioning part detected?
YES >> Refer to SRC-16, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003813938
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
 Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace harness connectors.
2.CHECK WIRING HARNESS
Check the wiring harness externals.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B1001
B1002
B1003
B1004
B1005CONTROL UNIT Air bag diagnosis sensor unit is mal-
functioning or out of the specification Malfunction in air bag diagnosis sen-
sor unit
 Configuration in air bag diagnosis
sensor unit dose not match to the ve-
hicles specification

B1001, B1002, B1003, B1004, B1005 DIAGNOSIS SENSOR UNIT
SRC-17
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
MA
B
SRC
N
O
P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace wiring harness.
3.REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to SR-22, "
Exploded View".
2. Perform DTC confirmation procedure. Refer to SRC-16, "
DTC Logic".
Is DTC detected?
YES >> GO TO 1.
NO >> INSPECTION END